Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm
Last Answer : (D) 200 mesh screen has 200 openings per linear cm
Description : The opening of a 200 mesh screen (Taylor series) is (A) 0.0074 cm (B) 0.0074 mm (C) 0.0047 cm (D) 74 milli-micron
Last Answer : (A) 0.0074 cm
Description : Higher is the mesh number, smaller will be the aperture size of the screen. It means that the aperture size of a 200 mesh screen will be smaller than that of 20 mesh screen. This is valid for (A) British ... (C) American standard screens (ASTM and Tyler standard screens) (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Pick out the correct statement. (A) Plastic chips are called non-cohesive solids (B) Kick's crushing law is, P/m = K . ln (D̅sa /Ds̅b ) (C) Communition is a generic term for size enlargement ... per ton of product, such that 80% of it passes through a 200 mesh screen, is called 'Work index'
Last Answer : (B) Kick's crushing law is, P/m = K . ln (D̅sa /Ds̅b )
Description : Mesh indicates the number of holes per (A) Square inch (B) Linear inch (C) Square foot (D) Linear foot
Last Answer : (B) Linear inch
Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014
Last Answer : (B) 0.30
Description : Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush ... of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns
Last Answer : (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen
Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Last Answer : Answer: Option B
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Last Answer : Answer: Option C
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Last Answer : Answer: Option D
Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2
Description : The ratio of the area of openings in one screen (Taylor series) to that of the openings in the next smaller screen is (A) 1.5 (B) 1 (C) √2 (D) None of these
Last Answer : (D) None of these
Description : Screen capacity is not a function of (A) Its openings size (B) Screening mechanism (C) Screening surface (D) Atmospheric humidity
Last Answer : (D) Atmospheric humidity
Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2
Description : Bottom openings 15 cm × 15 cm in the standing baffle wall are provided A. 15 cm c/c B. 22.5 cm c/c C. 30 cm c/c D. 50 cm c/c
Last Answer : ANS: B
Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these
Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg
Last Answer : (B) 250 kg
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm
Description : The unit of pressure in S.I. units is (a) kg/cm2 (b) mm of water column (c) pascal (d) dynes per square cm (e) bars
Last Answer : Answer : c
Description : Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these
Last Answer : (A) Rittinger's law
Description : 200 mesh sieve size corresponds to __________ microns. (A) 24 (B) 74 (C) 154 (D) 200
Last Answer : (B) 74
Description : Bucket elevators are not suitable for the vertical lifting of __________ materials. (A) Fine (e.g. - 200 mesh size coal) (B) Sticky (e.g. clay paste) (C) Small lumpy (e.g. grains and sand) (D) Free flowing
Last Answer : (B) Sticky (e.g. clay paste
Description : The most suitable equipment for the transportation of 200 mesh size particles is a (A) Bucket elevator (B) Pneumatic conveyor (C) Screw conveyor (D) Belt conveyor
Last Answer : (B) Pneumatic conveyor
Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Last Answer : (B) Ball mill
Description : 80% less than 200 mesh size particles are called (A) Smoke (B) Powder (C) Grit (D) Aggregates
Last Answer : (B) Powder
Description : or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000
Last Answer : (C) 500
Description : A sand mixture was screened through a standard 10-mesh screen. The mass fraction of the oversize material in feed, overflow and underflow were found to be 0.38, 0.79 and 0.22 respectively. The screen effectiveness based on the oversize is (A) 0.50 (B) 0.58 (C) 0.68 (D) 0.62
Last Answer : (A) 0.50
Description : The ratio of the actual mesh dimension of Taylor series to that of the next smaller screen is (A) 2 (B) √2 (C) 1.5 (D) √3
Last Answer : (B) √2
Description : Pick out the correct statement. (A) The capacity and the effectiveness of a screen are the same (B) The capacity and the effectiveness of screen are opposing factors (C) The screening surface of a 'reel' (a ... flour mills) is made of silk bolting cloth supported by wire mesh (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C
Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300
Last Answer : (B) 1 and 200
Description : Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm
Last Answer : (A) 5°C and 1 kgf/cm
Description : Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm
Last Answer : (A) 50°C and 3 - 4 kg/cm
Description : Absorption/scattering cross-section of an element is expressed in "barn", which is equivalent to (A) 10 -24 cm2 (B) 10 -12 cm (C) 1 Angstrom (D) 10 -24 cm
Last Answer : (A) 10 -24 cm
Description : The unit of specific cake resistance is (A) gm/cm2 (B) cm/gm (C) cm/gm2 (D) gm/gm
Last Answer : (A) gm/cm2 (
Description : The binary diffusivity in gases at atmospheric conditions is about (A) 10 -9 cm/sec (B) 10 -1 cm2 /sec (C) 10 -3 sec/cm (D) 10 -4 cm2 /sec
Last Answer : (B) 10 -1 cm2 /sec
Description : The unit of volumetric diffusivity is (A) cm2 /sec (B) cm/sec (C) cm3 /sec (D) cm2 /sec
Last Answer : (A) cm2 /sec
Description : . One stoke (unit of kinematic viscosity) is equivalent to (A) 1 cm2 /second (B) 1 m2 /second (C) 1 gm/cm. second (D) 1 kg. m/second
Last Answer : (A) 1 cm2 /second
Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630
Last Answer : (A) 7
Description : One poise (unit of absolute/dynamic viscosity) is equivalent to one (A) gm/cm2 . sec (B) gm/cm. sec (C) cm2 /sec (D) m2 /sec
Last Answer : (B) gm/cm. sec
Description : Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric ... (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these
Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞
Last Answer : (B) 1/[L√(K/D1 )]
Description : Unit of viscosity in CGS system is (A) gm .cm-1 sec-1 (B) gm . cm2 . sec-2 (C) gm .cm-2, sec-1 (D) gm . cm . sec-1
Last Answer : Option A
Description : In welded wire mesh, the longitudinal wire is placed at (A) 10 cm centres (B) 15 cm centres (C) 20 cm centres (D) 25 cm centres
Description : Shatter index of metallurgical coke on 2 inches and 0.5 inch screen should be respectively around __________ percent. (A) 80 and 97 (B) 95 and 100 (C) 40 and 70 (D) 25 and 97
Last Answer : (A) 80 and 97
Description : Steam pressures usually used in thermal power plants are (A) 5 kg/cm2 to 10 kg / cm2 (B) 50 kg/cm2 to 100 kg / cm2 (C) 110 kg/cm2 to 170 kg / cm2 (D) 200 kg/cm2 to 215 kg / cm2
Last Answer : Ans: C
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Description : The live load to be considered for an inaccessible roof, is (A) Nil (B) 75 kg/m2 (C) 150 kg/cm2 (D) 200 kg/m
Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Last Answer : (C) 200 kg/cm2