Description : A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature ... difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24
Last Answer : (B) 12
Description : A mixture of 10% C6H6 vapour in air at 25°C and 750 mm Hg has a dew point of 20°C. Its dew point at 30°C and 700 mm Hg will be around __________ °C. (A) 21.7 (B) 20 (C) 27.3 (D) 18.7
Last Answer : (D) 18.7
Description : Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205
Last Answer : (B) 135
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : There are five concentric layers within the atmosphere which is differentiated on the basis of temperature. The atmospheric layer which lies close to the earth's surface in which human being along with other organisms live is called ... is about __________ °C/km. (A) 0.05 (B) 1 (C) 6.5 (D) 15
Last Answer : (C) 6.5
Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at __________ °C. (A) < 0 (B) 10-30 (C) 250-280 (D) 500-600
Last Answer : (B) 10-30
Description : Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450
Last Answer : (B) 150
Description : While the fuel fired furnace can be used upto a maximum temperature of about 1700°C, the electric furnace can be used upto a temperature of about __________ °C. (A) 2000 (B) 3000 (C) 4500 (D) 6000
Last Answer : (C) 4500
Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C
Last Answer : (A) 7 kgf/cm2 and 70 °C
Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280
Last Answer : (D) 250-280
Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C. (A) -5 (B) 10-30 (C) 250-280 (D) 500-600
Last Answer : (C) 250-280
Description : Nitrobenzene (boiling point = 210.6°C) is steam distilled at 1 atm pressure. Nitrobenzene will distil off __________ °C. (A) At < 100 (B) At > 210.6 (C) Between 100 and 210 (D) None of these
Last Answer : (A) At < 100
Description : Very dilute solutions are generally used in fermentation reactions for which the optimum temperature range is __________ °C. (A) -5 to 0 (B) 5 to 10 (C) 30 to 50 (D) 75 to 80
Last Answer : (C) 30 to 50
Description : Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0
Last Answer : (A) 15-30
Description : Sublimation temperature of dry ice (solid CO2) is __________ °C. (A) -273 (B) 0 (C) -78 (D) 5
Last Answer : (C) -78
Description : Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99
Last Answer : (C) 0.95
Description : As the temperature of ice rises, the ice melts and its density _____. A. Decreases B. Remains constant C. Increases D. Increases upto 10 °C
Last Answer : ANSWER: C
Description : Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into ... °C b. 8.9°C c. 9.9°C d. 10.9°C formula: ΔQ = m c ΔT
Last Answer : 7.9 °C
Description : A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C. (A) 370 (B) 340 (C) 320 (D) 300
Last Answer : (A) 370
Description : The magnetic field intensity of an infinite sheet of charge with charge density 36.5 units in air will be a) 18.25 b) 11.25 c) 73 d) 1/36.5
Last Answer : a) 18.25
Description : A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0 ... that of the un-insulated steam pipe (D) Less than the steam pipe with 5 cms insulation
Last Answer : (B) Less than that of the un-insulated steam pipe
Description : Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150
Last Answer : (B) 45
Description : Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150
Last Answer : (B) 70
Description : Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140
Last Answer : (C) 90
Description : . Sodium melts (at atmospheric pressure) at a temperature of __________ °C. (A) 58 (B) 98 (C) 348 (D) 588
Last Answer : (B) 98
Description : Nitriding of steel is done (in electric furnace) at __________ °C. (A) 510 (B) 1720 (C) 2210 (D) 910
Last Answer : (A) 510
Description : Alpha iron is stable __________ °C. (A) Above 1403 (B) Upto 910 (C) Above 1800 (D) Between 910 & 1403
Last Answer : (B) Upto 910
Description : High speed steel tools retain their hardness upto a temperature of __________ °C. (A) 500 (B) 750 (C) 900 (D) 1100
Last Answer : (C) 900
Description : The wet and 'dry bulb temperature for a vapour-gas mixture are 25°C and 30°C respectively. If the mixture is heated to 45°C at constant pressure, the wet bulb temperature will be __________ °C. (A) 25 (B) > 25 (C) < 25 (D) - 25
Last Answer : (B) > 25
Description : Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000
Last Answer : (B) 200-330
Description : 1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these
Last Answer : (A) 1.49
Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50
Last Answer : (C) 70
Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250
Last Answer : (B) 750
Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250
Last Answer : (B) 130
Description : Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000
Last Answer : (B) 650
Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150
Last Answer : (C) 150
Description : Coal is heated in presence of air to a temperature of about __________ °C, while determining its ash content for proximate analysis. (A) 500 (B) 750 (C) 950 (D) 1100
Description : Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270
Last Answer : (A) 80-170
Description : Temperature of coke oven gas just before entering into saturator (for recovery of NH3 ) is about __________ °C. (A) 30 (B) 65 (C) 120
Last Answer : (B) 65
Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850
Last Answer : (B) 350 to 450
Description : Low temperature carbonisation of coal takes place at __________ °C. (A) 300 (B) 1100 (C) 700
Last Answer : (C) 700
Description : Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400
Last Answer : (A) 1100
Description : High temperature carbonisation of coal takes place at __________ °C. (A) 2000 (B) 600 (C) 1100 (D) 1600
Last Answer : (C) 1100
Description : Coal is heated in absence of air for 7 minutes at a temperature of about __________ °C, during its volatile matter determination for proximateanalysis. (A) 550 (B) 750 (C) 950 (D) 1150
Last Answer : (C) 950
Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800
Last Answer : (B) 900-1000
Description : Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450
Last Answer : (D) 1400-1450
Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200
Last Answer : (A) 700 - 1000
Description : Conversion of yellow phosphorous to red phosphorous is done by heating it in covered retorts at __________ °C in absence of air. (A) 50-80 (B) 250-400 (C) 1000-1200 (D) 800-900
Last Answer : (B) 250-400