The speech coding rate in D-AMPS is ____. A. 8 kbps B. 13 kbps C. 15 kbps D. 20 kbps

The speech coding rate in D-AMPS is ____.
A. 8 kbps
B. 13 kbps
C. 15 kbps
D. 20 kbps
by

1 Answer

Answer :

A. 8 kbps
by

Related questions

In GSM cellular system, the speech coding rate is ____. A. 13 kbps B. 8 kbps C. 15 kbps D. 20 kbps

Description : In GSM cellular system, the speech coding rate is ____. A. 13 kbps B. 8 kbps C. 15 kbps D. 20 kbps

Last Answer : A. 13 kbps

12 voice channels are sampled at 8000 sampling rate and encoded into 8 bit PCM word. Determine the rate of the data stream. a. 354 kbps b. 750 kbps c. 768 kbps d. 640 kbps

Description : 12 voice channels are sampled at 8000 sampling rate and encoded into 8 bit PCM word. Determine the rate of the data stream. a. 354 kbps b. 750 kbps c. 768 kbps d. 640 kbps

Last Answer : c. 768 kbps

In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Description : In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Last Answer : B. 64 kbps

Basic speed rate of digital system. A. 144 kbps B. 1,544 kbps C. 64 kbps D. 2,048 kbps

Description : Basic speed rate of digital system. A. 144 kbps B. 1,544 kbps C. 64 kbps D. 2,048 kbps

Last Answer : C. 64 kbps

What is the transmission rate of a GSM cellular systemA. 64 kbps B. 240 kbps C. 128 kbps D. 270 kbps

Description : What is the transmission rate of a GSM cellular system? A. 64 kbps B. 240 kbps C. 128 kbps D. 270 kbps

Last Answer : D. 270 kbps

What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Description : What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Last Answer : C. 64 kbps

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Description : The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Last Answer : 10 – 1000 microwatts

Calculate the reverberation time of a living room 8 ft high, 13 ft wide and 20 ft long. The total absorption of the building structure inside the room is 180.7 sabines with four persons present in the room. A. 0.5 ms B. 0.05 s C. 0.5 s D. 5 ms

Description : Calculate the reverberation time of a living room 8 ft high, 13 ft wide and 20 ft long. The total absorption of the building structure inside the room is 180.7 sabines with four persons present in the room. A. 0.5 ms B. 0.05 s C. 0.5 s D. 5 ms

Last Answer : C. 0.5 s

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Last Answer : c. 32 Kbps

Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Description : Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Last Answer : a. 2 sec

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ................ (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Description : Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ... ...... (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Last Answer : Answer: Marks given to all

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Last Answer : (C) 32 Kbps

In the illustrated circuit, what is the total resistance if the voltage is 10 VDC, the resistance of R2 is 40 ohms and the total current is .75 amps? EL-0019 A. 13 1/3 ohms B. 20 ohms C. 60 ohms D. the answer can not be determined from the information given

Description : In the illustrated circuit, what is the total resistance if the voltage is 10 VDC, the resistance of R2 is 40 ohms and the total current is .75 amps? EL-0019 A. 13 1/3 ohms B. 20 ohms C. 60 ohms D. the answer can not be determined from the information given

Last Answer : Answer: A

Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Description : Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Last Answer : B. NTT

How frequency to voltage converted on OP-AMPS.

Description : How frequency to voltage converted on OP-AMPS.

Last Answer : A Frequency to voltage converter produces an output voltage, whose amplitude is a function of frequency of the input signal. The input signal may be a sinewave, a square wave or a pulse train. The F/V converter is essentially an FM detector or discriminator.

Mention some of the non – linear applications of op-amps

Description : Mention some of the non – linear applications of op-amps

Last Answer : Rectifier, peak detector, clipper, clamper, sample and hold circuit, log amplifier, anti –log amplifier, multiplier are some of the non – linear op-amp circuits. 

Mention some of the linear applications of op – amps.

Description : Mention some of the linear applications of op – amps.

Last Answer : Adder, subtractor, voltage –to- current converter, current –to- voltage converters, instrumentation amplifier, analog computation ,power amplifier, etc are some of the linear opamp circuits.

What is the need for frequency compensation in practical op-amps?

Description : What is the need for frequency compensation in practical op-amps?

Last Answer : Frequency compensation is needed when large bandwidth and lower closed loop gain is desired. Compensating networks are used to control the phase shift and hence to improve the stability.

In practical op-amps, what is the effect of high frequency on its performance?

Description : In practical op-amps, what is the effect of high frequency on its performance?

Last Answer : The open-loop gain of op-amp decreases at higher frequencies due to the presence of parasitic capacitance. The closed-loop gain increases at higher frequencies and leads to instability.

For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Description : For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Last Answer : A. 1

What is the optimum volume per person of rooms for speech? A. 2.8 B. 3.1 C. 4.2 D. 5.1

Description : What is the optimum volume per person of rooms for speech? A. 2.8 B. 3.1 C. 4.2 D. 5.1

Last Answer : A. 2.8

Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Description : Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Last Answer : C. 2400

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Description : Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Last Answer : B. Sampling, quantizing, and coding

The transformer signal coding method for T1 carrier is A. Binary B. NRZ C. Manchester D. Bipolar

Description : The transformer signal coding method for T1 carrier is A. Binary B. NRZ C. Manchester D. Bipolar

Last Answer : D. Bipolar

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW

Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B is 128 kbps. What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Description : Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B ... What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Last Answer : b. 40

Station A uses 32 byte packets to transmit messages to station B using sliding window protocol. The round trip delay between A and B is 40 milli seconds and the bottleneck bandwidth on the path between A and B is 64 kbps. The optimal window size of A is (1) 20 (2) 10 (3) 30 (4) 40

Description : Station A uses 32 byte packets to transmit messages to station B using sliding window protocol. The round trip delay between A and B is 40 milli seconds and the bottleneck bandwidth on the path between A and B is 64 kbps. The optimal window size of A is (1) 20 (2) 10 (3) 30 (4) 40

Last Answer : (2) 10

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Description : A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Last Answer : 6 Kbps

Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Description : Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Last Answer : c. 1000 Mbps

Broad Band ISDN handles data rate of about (A) 64 kbps (B) 100 mbps (C) 5.4 mbps (D) 2.048 mbps

Description : Broad Band ISDN handles data rate of about (A) 64 kbps (B) 100 mbps (C) 5.4 mbps (D) 2.048 mbps

Last Answer : (A) 64 kbps

How much packet data rate per user is supported by W-CDMA if the user is stationary? a) 2.048 Kbps b) 100 Mbps c) 2.048 Mbps d) 1 Gbps

Description : How much packet data rate per user is supported by W-CDMA if the user is stationary? a) 2.048 Kbps b) 100 Mbps c) 2.048 Mbps d) 1 Gbps

Last Answer : c) 2.048 Mbps

What is the channel symbol rate in Bluetooth for each user? a) 270.833 Kbps b) 1 Gbps c) 100 Mbps d) 1 Mbps

Description : What is the channel symbol rate in Bluetooth for each user? a) 270.833 Kbps b) 1 Gbps c) 100 Mbps d) 1 Mbps

Last Answer : d) 1 Mbps

A multiplexer combines four 100-Kbps channels using a time slot of 2 bits. What is the bit rate? (A) 100 Kbps (B) 200 Kbps (C) 400 kbps (D) 1000 Kbps

Description : A multiplexer combines four 100-Kbps channels using a time slot of 2 bits. What is the bit rate? (A) 100 Kbps (B) 200 Kbps (C) 400 kbps (D) 1000 Kbps

Last Answer : (C) 400 kbps

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

Find the equivalent inductance per foot of the above cable? A. 13.5 nF/ft B. 13.5 pF/ft C. 116.8 nH/ft D. 116.8 pF/ft

Description : Find the equivalent inductance per foot of the above cable? A. 13.5 nF/ft B. 13.5 pF/ft C. 116.8 nH/ft D. 116.8 pF/ft

Last Answer : C. 116.8 nH/ft

In the illustrated circuit, what is the total current if the voltage is 12 VDC, the resistance of R1 is 15 ohms, and the resistance of R2 is 10 ohms? EL-0019 A. .8 amps B. 1.5 amps C. .55 amps D. 2 amps

Description : In the illustrated circuit, what is the total current if the voltage is 12 VDC, the resistance of R1 is 15 ohms, and the resistance of R2 is 10 ohms? EL-0019 A. .8 amps B. 1.5 amps C. .55 amps D. 2 amps

Last Answer : Answer: D

What is considered the most obvious conveyor of information? A. Sound B. Speech C. Music D. Noise

Description : What is considered the most obvious conveyor of information? A. Sound B. Speech C. Music D. Noise

Last Answer : B. Speech

A method of expressing the amplitude of complex non-periodic signals such as speech. A. Frequency B. Wavelength C. Volume D. Pitch

Description : A method of expressing the amplitude of complex non-periodic signals such as speech. A. Frequency B. Wavelength C. Volume D. Pitch

Last Answer : C. Volume

______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Description : ______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Last Answer : C. Volume unit meter

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be________. EL-0018 A. 0.887 amps B. 1.127 amps C. 234 m amps D. 2.13 amps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be________. EL-0018 A. 0.887 amps B. 1.127 amps C. 234 m amps D. 2.13 amps

Last Answer : Answer: B