Description : The prime mover of an AC two pole main propulsion generator drives the generator at 3600 RPM. If the main propulsion motor has 80 poles, what will be the propeller speed? A. 45 RPM B. 80 RPM C. 90 RPM D. 180 RPM
Last Answer : Answer: C
Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor
Last Answer : Answer: A
Description : In an AC synchronous motor electric propulsion plant, propeller speed is controlled by varying the _____________. A. prime mover speed B. electric coupling field strength C. number of energized main motor poles D. propulsion generator field strength
Description : In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds
Description : The direction of propeller shaft rotation in a turbo-electric synchronous propulsion drive motor is changed by reversing the _____________. A. polarity of the propulsion motor B. polarity of the propulsion generator C. phase sequence of power to the motor D. phase sequence of power to the generator
Description : A four-pole 60-hertz induction motor has a synchronous speed of 1800 RPM and a slip of 4 percent at full load. What will be its full load speed? A. 1728.0 RPM B. 1730.7 RPM C. 1800.0 RPM D. 1872.0 RPM
Description : A four-pole, 60 cycle, squirrel-cage motor has a full load speed of 1725 RPM. What will be the percent of slip at full load? A. 4.16 B. 4.34 C. 95.66 D. 95.84
Description : What is the rotor speed of a four pole, 60 cycle, induction motor operating at full load with 3% slip? A. 270 RPM B. 540 RPM C. 873 RPM D. 1746 RPM
Last Answer : Answer: D
Description : A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately ___________. A. 850 RPM B. 1,150 RPM C. 1,750 RPM D. 3,550 RPM
Description : If the synchronous speed of a 12 pole, polyphase, induction motor operating at 60 Hz were 600 RPM, how many poles will be required in a similar motor operating at the same frequency but having a synchronous speed of 900 RPM? A. 4 B. 6 C. 8 D. 18
Description : A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized? A. 0 B. 1.1 C. 2.2 D. 3.3
Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits
Last Answer : Answer: B
Description : A 3-phase, 400 votts, 50 Hz, 100 KW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm
Last Answer : Ans: B N = NS (1-S) and NS =120 f / p =120 x 50 /4 = 1500 rpm ∴N= 1500 (1-0.02) =1470 rpm
Description : A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.
Last Answer : Ans: D Given N = 1500 rpm, Φ = 0.4 mWb, Z = 1000, P = 4, & A= 4 Therefore, Eb = NΦPZ / 60 A = 1500 x 0.4 x 4 x 1000 x 10^-3 / 60 x 4 = 60/6 = 10 volts
Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above
Last Answer : a.100-120 rpm
Description : Uneven wear of the commutator surface on a direct current propulsion motor can be caused by _____________. A. rapid change in load B. excessive operation at light load C. incorrect brush staggering D. unequal pole spacing
Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.
Last Answer : (C) less than 800 rpm.
Description : A 1.8°step, 4-phase stepper motor has a total of 40 teeth on 8 pole of stator. The number of rotor teeth for their rotor will be (A) 40 (B) 50 (C) 100 (D) 80
Last Answer : (B) 50
Description : On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush ... B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation
Description : The synchronous speed for a 3 phase 6-pole induction motor is 1200 rpm. If the number of poles is now reduced to 4 with the frequency remaining constant, the rotor speed with a slip of 5% will be _________. (A) 1690 rpm (B) 1750 rpm (C) 1500 rpm (D) 1710 rpm
Last Answer : (D) 1710 rpm
Description : Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency? A. A four-pole synchronous motor under normal load. B. A four-pole induction motor under ... A six-pole synchronous motor under normal load. D. A six-pole induction motor under full load.
Description : A turbogenerator has a rated output of 1200 KW at 60 Hertz, with a no load frequency of 61.5 Hertz. What is its speed droop? A. 1.03% B. 1.50% C. 2.44% D. 2.50%
Description : What is the limit of MG/DL, of blood sugar in the normal person at the time of fast? (1) 40-60 (2) 120-150 (3) 70-100 (4) 160-200
Last Answer : (3) 70-100 Explanation: The mean normal blood glucose level in humans is about 4 mM (4 mmol/L, or 72 mg/dL, i.e. milligrams/deciliter); however, this level fluctuates throughout the day. Glucose ... day (termed "the fasting level"), and rise after meals for an hour or two by a few millimolar.
Description : What is the limit of MG/DL of blood sugar in the normal person at the time of fast ? (1) 40-60 (2) 120-150 (3) 70-100 (4) 160-200
Last Answer : 70-100
Description : An AC generator produces 60 Hz at 1800 RPM. If the generator speed is increased to 1830 RPM, the cycles will _____________. A. remain at 60 Hz B. increase to 61 Hz C. decrease to 59 Hz D. increase to 63 Hz
Description : The source of emergency lighting and power at loss of normal ship's power on a cargo vessel should be obtained from the ______________. A. emergency generator supply to the emergency ... switchboard C. battery supply to the main switchboard D. turbogenerator supply to the emergency switchboard
Description : The voltage of an operating AC turbogenerator is raised or lowered by adjusting the _____________. A. exciter generator governor controls B. synchronizing switch C. phase sequence switch D. generator field exciter
Description : On a vessel with turbo-electric drive, which of the following conditions would indicate that the propulsion motor had dropped out of synchronization with the propulsion generator? A. Excessive ... Tripped main motor interlocks C. Overheated crosstie busses D. Closed contact in the field circuits
Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)
Last Answer : (A) Produces mainly axial flow
Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes
Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM
Description : The rotor frequency for a 3 phase 1000 RPM 6 pole induction motor with a slip of 0.04 is________Hz (A) 8 (B) 4 (C) 6 (D) 2
Last Answer : Ans: D Given: N=1000 rpm ; P= 6; s= 0.04; and f = NP/ 120 = 10006/120 = 50 Hz Rotor frequency fr=sf = 0.0450 = 2.0 Hz
Description : 4725,1050,300,120,80,? 1 : 40 2 : 160 3 : 120 4 : 110 5 : 60
Last Answer : Answer-2 (160) Explanation- 4725 / 4.5=1050 1050/3.5=300 300/2.5=120 120/1.5=80 80/0.5=160
Description : Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.
Description : Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.
Description : A 3-phase, 4-pole, 50Hz induction motor runs at a speed of 1440 rpm. The rotating field produced by the rotor rotates at a speed of ________ rpm with respect to stator field. (A) 1500 (B) 0 (C) 1440 (D) 60
Last Answer : 0
Description : The blood cholesterol level in 100ml of blood in a normal person varies between (1) 150 and 200 mg (2) 120 and 200 mg (3) 100 and 180 mg (4) 80 and 160 mg
Last Answer : (1) 150 and 200 mg Explanation: Cholesterol is defined as a waxy alcohol, fat-like substance that occurs naturally in all areas of the human body. Cholesterol is measured in milligrams per 100 ... to be normal blood cholesterol; 200-239 mg/dL borderlinehigh; and > 240 mg/dl high cholesterol.
Description : The blood cholesterol level in 100 ml of blood in a normal person varies between— (1) 150 and 200 mg (2) 120 and 200 mg (3) 100 and 180 mg (4) 80 and 160 mg
Last Answer : 150 and 200 mg
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : The synchronous speed of an induction motor is the ________. A. speed at which the rotor turns B. speed of the rotating field C. frequency of the rotor current D. slip in per cent of rotor RPM
Description : Which of the following will happen to the alternator frequency if the load is removed from a turbogenerator, whose governor has a 3% speed droop? A. It will remain unchanged. B. It will decrease by approximately 3%. C. It will become variable. D. It will increase.
Description : When starting a DC propulsion motor the variable rheostat must FIRST be turned ____________. A. all the way to the run position then quickly back to slow B. to the slow position then gradually moved to full speed C. to the mid position D. quickly to the run position
Description : The fasting blood glucose level in adults in mg/100 ml is – (1) 200 (2) 160 (3) 100 (4) 60
Last Answer : (3) 100 Explanation: The normal range of concentration of fasting blood sugar is 80 to 120 mg/ml; in the testing of true blood sugar, the normal range of concentration is 70 to 100 ... normal glucose levels fall between 70 and 150 mg. Higher levels may indicate diseases such as diabetes mellitus.
Description : The fasting blood glucose level in adults in mg/100 ml is (1) 200 (2) 160 (3) 100 (4) 60
Last Answer : 100
Description : A toothed type Tacho-generator has 60 teeth. A magnetic pickup is used in conjunction with it. The number of pulses generated per second in the magnetic pick up is : - a) 3000 b) 1500 c) 1800 d) 1200
Last Answer : 1500
Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'
Description : Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. ... is held below the rated current. D. The field winding is energized for starting purposes only.
Description : What will be the frequency of a three-phase, six pole, AC generator operating at 1800 revolutions per minute? A. 60 hertz B. 90 hertz C. 120 hertz D. 180 hertz
Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is
Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm
Description : A 60 Hz, 4 pole turbo generator rated 100 MVA, 13.8 KV has an inertia constant of 10 MJ/MVA. Find the stored energy in the rotor at synchronous speed. (A) 10 MJ (B) 100 J (C) 1000 J (D) 1000 MJ
Last Answer : c
Description : An 8-pole alternator runs at 750 rpm and supplies power to a 6-pole induction motor which has a full load slip of 3 percent. The full load speed of the induction motor will be: A) 1000 rpm B) 920 rpm C) 950 rpm D) 970 rpm
Last Answer : An 8-pole alternator runs at 750 rpm and supplies power to a 6-pole induction motor which has a full load slip of 3 percent. The full load speed of the induction motor will be: 970 rpm