The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity
by

1 Answer

Answer :

Ans: a
by
selected by

Related questions

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Description : A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Last Answer : Ans: b

A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Description : A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Last Answer : ANSWER : A

In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke

Description : In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke

Last Answer : ANSWER : B

In a two stage reciprocating air compressor with a suction pressure of 2 bar and delivery pressure of 8 bar the ideal intercooler pressure will be A. 10 bar B. 6 bar C. 4 bar D. 3 bar

Description : In a two stage reciprocating air compressor with a suction pressure of 2 bar and delivery pressure of 8 bar the ideal intercooler pressure will be A. 10 bar B. 6 bar C. 4 bar D. 3 bar

Last Answer : ANSWER : C

In a single stage reciprocating air compressor, the work done on air to compressor is from suction pressure to delivery pressure will be minimum when the compression is A. Isothermal process B. Adiabatic process C. Polytropic process D. Constant pressure process.

Description : In a single stage reciprocating air compressor, the work done on air to compressor is from suction pressure to delivery pressure will be minimum when the compression is A. Isothermal process B. Adiabatic process C. Polytropic process D. Constant pressure process.

Last Answer : ANSWER : A

In a two stage reciprocating air compressor, the suction and delivery pressure are 1 and 4 bar respectively. For maximum efficiency the intercooler pressure is A. 1.5 bar B. 2 bar C. 2.5 bar D. 3 bar

Description : In a two stage reciprocating air compressor, the suction and delivery pressure are 1 and 4 bar respectively. For maximum efficiency the intercooler pressure is A. 1.5 bar B. 2 bar C. 2.5 bar D. 3 bar

Last Answer : ANSWER : B

A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Description : A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Last Answer : ANSWER : A

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

The volume of air delivered by the compressor is called A. Free air delivery B. Compressor capacity C. Swept volume D. Mean effective pressure

Description : The volume of air delivered by the compressor is called A. Free air delivery B. Compressor capacity C. Swept volume D. Mean effective pressure

Last Answer : ANSWER : B

In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Last Answer : Ans: a

With suction pressure being atmospheric, increase in delivery pressure with fixed clearance volume A. increase volumetric efficiency B. decrease volumetric efficiency C. does not change volumetric efficiency D. First increase volumetric efficiency and then decrease it

Description : With suction pressure being atmospheric, increase in delivery pressure with fixed clearance volume A. increase volumetric efficiency B. decrease volumetric efficiency C. does not change volumetric efficiency D. First increase volumetric efficiency and then decrease it

Last Answer : ANSWER : B

The COP of a vapour compression plant in comparison to vapour absorption plant is (a) more (b) less (c) same (d) more/less depending on size of plant

Description : The COP of a vapour compression plant in comparison to vapour absorption plant is (a) more (b) less (c) same (d) more/less depending on size of plant

Last Answer : Ans: a

For a two stage compressor, the ratio of diameter of low pressure cylinder to high pressure cylinder is equal to A. Square of the ratio of final pressure to initial pressure B. The ratio of final pressure to initial pressure C. The square root of the ratio of final pressure to initial pressure D. Cube root of the ratio of final pressure to initial pressure

Description : For a two stage compressor, the ratio of diameter of low pressure cylinder to high pressure cylinder is equal to A. Square of the ratio of final pressure to initial pressure B. The ratio of ... final pressure to initial pressure D. Cube root of the ratio of final pressure to initial pressure

Last Answer : ANSWER : C

For ammonia refrigerating systems, the tubes of a shell and tube condenser are made of (a) copper (b) aluminium (c) steel (d) brass

Description : For ammonia refrigerating systems, the tubes of a shell and tube condenser are made of (a) copper (b) aluminium (c) steel (d) brass

Last Answer : Ans: c

The maximum delivery pressure in a rotary air compressor is A. 10 bar B. 20 bar C. 30 bar D. 50 bar

Description : The maximum delivery pressure in a rotary air compressor is A. 10 bar B. 20 bar C. 30 bar D. 50 bar

Last Answer : ANSWER : A

In a four stage compressor, if the pressure at the first and third stage are 1 bar and 16 bar, then the delivery pressure at the fourth stage will be A. 1 bar B. 16 bar C. 64 bar D. 256 bar

Description : In a four stage compressor, if the pressure at the first and third stage are 1 bar and 16 bar, then the delivery pressure at the fourth stage will be A. 1 bar B. 16 bar C. 64 bar D. 256 bar

Last Answer : ANSWER : C

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

The air requirement of a petrol engine during starting compared to theoretical air required for complete combustion is a. more b. less c. same d. may be more or less depending on engine capacity

Description : The air requirement of a petrol engine during starting compared to theoretical air required for complete combustion is a. more b. less c. same d. may be more or less depending on engine capacity

Last Answer : ANSWER b. less

For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should be used (c) perfectly tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Last Answer : Ans: c

In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Description : In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Last Answer : Ans: b

The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Description : The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Last Answer : ANSWER : D

The capacity of a compressor is expressed in A. B. C. D.

Description : The capacity of a compressor is expressed in A. B. C. D.

Last Answer : ANSWER : C

The capacity of the compressor will be highest when its intake temperature is A. Lowest B. highest C. Atmospheric D. Unpredictable

Description : The capacity of the compressor will be highest when its intake temperature is A. Lowest B. highest C. Atmospheric D. Unpredictable

Last Answer : ANSWER : C

The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Description : The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Last Answer : Ans: d

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Description : The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Last Answer : ANSWER : A

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

Fuel is injected into the cylinder at the end of ______________ stroke. a) suction b) compression c) expansion d) exhaust

Description : Fuel is injected into the cylinder at the end of ______________ stroke. a) suction b) compression c) expansion d) exhaust

Last Answer : Answer: b Explanation: Fuel is injected into the cylinder at the end of compression stroke and not at suction or expansion stroke.

For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Description : For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Last Answer : ANSWER : C

The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6%

Description : The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6% 

Last Answer : d) 1.6%

The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Description : The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Last Answer : Ans: a

The refrigeration effect in a dry evaporator compared to flooded evaporator in a similar plant is (a) same (b) more (c) less (d) more or less depending on ambient conditions

Description : The refrigeration effect in a dry evaporator compared to flooded evaporator in a similar plant is (a) same (b) more (c) less (d) more or less depending on ambient conditions

Last Answer : Ans: c

The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Description : The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Last Answer : Ans: a

If the evaporator temperature of a plant is lowered, keeping the condenser temperature constant, the h.p. of compressorrequired will be (a) same (b) more (c) less (d) more/less depending on rating

Description : If the evaporator temperature of a plant is lowered, keeping the condenser temperature constant, the h.p. of compressorrequired will be (a) same (b) more (c) less (d) more/less depending on rating

Last Answer : Ans: b

The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be lower (c) will remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Description : The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be ... remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Last Answer : Ans: a

The thermal efficiency of a diesel cycle having fixed compression ratio with increase in cut-off ratio will a. increase b. decrease c. independent d. increase or decrease depending upon other factors

Description : The thermal efficiency of a diesel cycle having fixed compression ratio with increase in cut-off ratio will a. increase b. decrease c. independent d. increase or decrease depending upon other factors

Last Answer : ANSWER b. decrease

The C.O.P. of a domestic refrigerator in comparison to domestic air conditioner will be (a) same (b) more (c) less (d) dependent on weather conditions

Description : The C.O.P. of a domestic refrigerator in comparison to domestic air conditioner will be (a) same (b) more (c) less (d) dependent on weather conditions

Last Answer : Ans: c

Mass flow ratio of NH3 in comparison to Freon-12 for same refrigeration load and same temperature limits is of the orderof (a) 1 : 1 (b) 1 : 9 (c) 9 : 1 (d) 1 : 3

Description : Mass flow ratio of NH3 in comparison to Freon-12 for same refrigeration load and same temperature limits is of the orderof (a) 1 : 1 (b) 1 : 9 (c) 9 : 1 (d) 1 : 3

Last Answer : Ans: b

Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium bromide plant to remove the unwanted water vapour by condensing (d) concentration of solution coming out of lithium bromide generator is more in comparison to that entering the generator

Description : Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium ... of solution coming out of lithium bromide generator is more in comparison to that entering the generator

Last Answer : Ans: c

The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Last Answer : ANSWER : B

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

Classification of air compressor

Description : Classification Of Air Compressor

Last Answer : Air compressors are classified in several different ways, depending on the specific characteristics and features of the compressor. Here are a few common ways that air compressors are classified: ... range of sizes and capacities, from small, portable units to large, industrial-sized compressors.

The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Last Answer : Ans: d

For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Description : For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Last Answer : Ans: b

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Description : In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Last Answer : Ans: d

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Description : Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Last Answer : Ans: a

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d