The capacity of the compressor will be highest when its intake temperature is A. Lowest B. highest C. Atmospheric D. Unpredictable

The capacity of the compressor will be highest when its intake temperature is A. Lowest B. highest C. Atmospheric D. Unpredictable  
by

1 Answer

Answer :

ANSWER : C
by
selected by

Related questions

If the intake air temperature of Internal combustion engine increases, its efficiency will a. increase b. decrease c.remains same d unpredictable

Description : If the intake air temperature of Internal combustion engine increases, its efficiency will a. increase b. decrease c.remains same d unpredictable

Last Answer : ANSWER b. decrease

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

The compressor performance at higher altitude compare to sea level will be A. Same B. Higher C. Lower D. Unpredictable

Description : The compressor performance at higher altitude compare to sea level will be A. Same B. Higher C. Lower D. Unpredictable

Last Answer : ANSWER : C

The area of actual indicator diagram on an air compressor as compared to area of ideal indicator diagram is A. Less B. More C. Same D. Unpredictable

Description : The area of actual indicator diagram on an air compressor as compared to area of ideal indicator diagram is A. Less B. More C. Same D. Unpredictable

Last Answer : ANSWER : B

Compressor at high altitude will draw A. More power B. Less power C. Same power D. Unpredictable

Description : Compressor at high altitude will draw A. More power B. Less power C. Same power D. Unpredictable

Last Answer : ANSWER : B

Volumetric efficiency of a compressor without clearance volume A. Increases with increase in compression ratio B. Decreases wit increase in compression ratio C. Not dependent upon compression ratio D. Unpredictable

Description : Volumetric efficiency of a compressor without clearance volume A. Increases with increase in compression ratio B. Decreases wit increase in compression ratio C. Not dependent upon compression ratio D. Unpredictable

Last Answer : ANSWER : C

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Description : Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Last Answer : ANSWER : A

The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Description : The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Last Answer : Ans: a

The volume of air delivered by the compressor is called A. Free air delivery B. Compressor capacity C. Swept volume D. Mean effective pressure

Description : The volume of air delivered by the compressor is called A. Free air delivery B. Compressor capacity C. Swept volume D. Mean effective pressure

Last Answer : ANSWER : B

The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Description : The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Last Answer : ANSWER : D

The capacity of a compressor is expressed in A. B. C. D.

Description : The capacity of a compressor is expressed in A. B. C. D.

Last Answer : ANSWER : C

The change in evaporator temperature in a refrigeration cycle, as compared to change in condenser temperature, influences the value of C.O.P. (a) more (b) less (c) equally. (d) unpredictable

Description : The change in evaporator temperature in a refrigeration cycle, as compared to change in condenser temperature, influences the value of C.O.P. (a) more (b) less (c) equally. (d) unpredictable

Last Answer : Ans: a

When the dew point temperature is equal to the air temperature then the relative humidity is A. 0% B. 50% C. 100% D. unpredictable

Description : When the dew point temperature is equal to the air temperature then the relative humidity is A. 0% B. 50% C. 100% D. unpredictable

Last Answer : ANSWER : C

The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: c Explanation: The air flow sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel while exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

Keeping other parameters constant brake power of diesel engine can be increased by (a) Decreasing the density of intake air (b) Increasing the temperature of intake air (c) Increasing the pressure of intake air (d) Decreasing the pressure of intake air

Description : Keeping other parameters constant brake power of diesel engine can be increased by (a) Decreasing the density of intake air (b) Increasing the temperature of intake air (c) Increasing the pressure of intake air (d) Decreasing the pressure of intake air

Last Answer : Ans : c

If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Description : If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Last Answer : ANSWER a. increase

When the rate of evaporation of water is zero, the relative humidity of the air is A. 0% B. 100% C. 50% D. unpredictable

Description : When the rate of evaporation of water is zero, the relative humidity of the air is A. 0% B. 100% C. 50% D. unpredictable

Last Answer : ANSWER : B

The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Description : The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Last Answer : ANSWER : A

The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable

Description : The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable

Last Answer : ANSWER : B

The air requirement of a petrol engine during starting compared to the theoretical air requirement for complete combustion is A. more B.unpredictable C. same D. less

Description : The air requirement of a petrol engine during starting compared to the theoretical air requirement for complete combustion is A. more B.unpredictable C. same D. less

Last Answer : ANSWER : D

Thermal efficiency of an internal combustion engine on weak mixture is a. higher b. lower c. unaffected d. unpredictable

Description : Thermal efficiency of an internal combustion engine on weak mixture is a. higher b. lower c. unaffected d. unpredictable

Last Answer : ANSWER a. higher

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d

The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Description : The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Last Answer : Ans: a

Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Description : Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Last Answer : ANSWER : B

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Description : The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Last Answer : ANSWER : D

In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Description : In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Last Answer : The compression ratio in a Compression Ignition (CI) engine is generally in between a. 8 to 13 b. 14 to 23 c. 20 to 28 d. 25 to 32 (Ans:b)

In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Description : In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Last Answer : Answer: d Explanation: None.

In electronic fuel injection, there is improvement in the _____________ efficiency due to comparatively less resistance in the intake manifolds which will cause less pressure losses. a) mechanical b) volumetric c) overall d) none of the mentioned

Description : In electronic fuel injection, there is improvement in the _____________ efficiency due to comparatively less resistance in the intake manifolds which will cause less pressure losses. a) mechanical b) volumetric c) overall d) none of the mentioned

Last Answer : Answer: b Explanation: In electronic fuel injection, there is improvement only in the volumetric efficiency due to comparatively less resistance in the intake manifolds which will cause less pressure losses and no other efficiencies are hindered.

The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: b Explanation: The manifold pressure sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load and the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.

Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure d. Volume of 1 kg of dry air at 21°C and atmospheric pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Description : Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure ... pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Last Answer : Answer: D

Dry-bulb temperature is: a. The absolute temperature corresponding to the atmospheric pressure b. The same as the wet-bulb temperature if the relative humidity is less than 100% c. Not required to find the relative humidity d. The temperature of the air measured with an ordinary thermometer e. The dew point temperature

Description : Dry-bulb temperature is: a. The absolute temperature corresponding to the atmospheric pressure b. The same as the wet-bulb temperature if the relative humidity is less than 100% c. Not required ... d. The temperature of the air measured with an ordinary thermometer e. The dew point temperature

Last Answer : Answer: D

Dew point can be best defined as the: a. Absolute temperature at which air, upon heating, will evaporate moisture b. . Percentage of moisture that air can hold at a given temperature and pressure c. . Temperature that air will begin to evaporate moisture d. . Temperature at which air, upon cooling, becomes saturated, causing moisture to condense should the temperature drop further e. . Atmospheric pressure at which air will condense moisture

Description : Dew point can be best defined as the: a. Absolute temperature at which air, upon heating, will evaporate moisture b. . Percentage of moisture that air can hold at a given temperature ... to condense should the temperature drop further e. . Atmospheric pressure at which air will condense moisture

Last Answer : Answer: D

Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases with pressure ratio C. Its volumetric efficiency does not vary with change in clearance ratio and pressure ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Description : Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases ... ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Last Answer : ANSWER : D

Classification of air compressor

Description : Classification Of Air Compressor

Last Answer : Air compressors are classified in several different ways, depending on the specific characteristics and features of the compressor. Here are a few common ways that air compressors are classified: ... range of sizes and capacities, from small, portable units to large, industrial-sized compressors.

The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Last Answer : Ans: d

For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Description : For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Last Answer : Ans: b

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Description : In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Last Answer : Ans: d

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Last Answer : Ans: a

Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Description : Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Last Answer : Ans: a

Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Description : Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Last Answer : Ans: a

The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Description : The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Last Answer : Ans: d

In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Description : In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Last Answer : Ans: D

A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Description : A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Last Answer : ANSWER : D

Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Description : Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Last Answer : Ans : c

Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Description : Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Last Answer : ANSWER : A