1 Answer

Answer :

SCR turned off when the anode current falls below holding current.

Related questions

Description : The SCR would be turned OFF by voltage reversal of applied anode-cathode ac supply frequency of A) 10 kHz B) 10 Hz C) 5 kHz D) 5 Hz 

Description : How is the GTO turned off? A) By using a commutation circuit B) By applying reverse gate pulse C) By using a latch-up circuit D) By reverse anode current pulse 

Last Answer : How is the GTO turned off? A) By using a commutation circuit B) By applying reverse gate pulse C) By using a latch-up circuit D) By reverse anode current pulse 

Description : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

Last Answer : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in voltage notching

Description : thyristor can be turned off by?

Last Answer : Thyristor can be turned off by making anode potential equal to cathode potential or by making anode potential less than cathode potential.

Description : drive the expression for the  (1)current that commutates the scr, (2)the peak current, (3) conduction time?  in class B,C,D and E.

Description : What is holding current and latching current in SCR? Draw the gate characteristics of an SCR and explain the characteristics. What are the different signals which can be used for turning on SCR by gate control? compare them.

Last Answer : (i) Holding Current: Holding current is defined as the minimum anode current required to maintain conducting SCR in the on-state.  (ii) Latching Current: Latching current is defined as the ... the on-state immediately after the SCR has been turned on and the gate signal has been removed.

Description : Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Last Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

Description : Which is the positive terminal anode or cathode?

Last Answer : Anode is positive terminal and cathode is negative terminal.

Description : Is the anode or cathode longer in LED ?

Last Answer : In LED anode terminal is longer and cathode terminal is smaller.

Description : Explain triggering of SCR using opto-coupler. State its advantages. 

Last Answer : Triggering of SCR using opto-coupler:  A simple opto-coupler based triggering circuit for SCR is shown in the figure. An optocoupler or opto-isolator is a combination of light source ... is small size and light weight device. iii)Interfacing with logic circuits is easily possible.

Description : Draw the circuit diagram of battery charger using SCR and explain it’s working.

Last Answer : Battery charger circuit using SCR: The figure shows the battery charger circuit using SCR. A 12V discharged battery is connected in the circuit and switch SW is closed. The singlephase 230V ... not fired. In this way, after full charging, further charging is automatically stopped.

Description : Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Last Answer : Types of Triggering: 1) Forward voltage triggering 2) Thermal triggering (Temperature triggering) 3) Radiation triggering (Light triggering) 4) dv/dt triggering 5) Gate triggering ... generated leakage current increases. This current gets multiplied internally and thyristor is turned on. 

Description : Explain working of AC circuit breaker using SCR with circuit diagram.

Last Answer : AC Circuit Breaker:  The circuit configuration of static AC circuit breaker using SCR is shown in the figure. When switch S' is closed, the SCRs T1 and T2 are fired in positive ... to non-availability of gate current. Thus the maximum time delay for breaking the circuit is one half-cycle.

Description : Temperature controller using SCR

Last Answer : Temperature controller using SCR The temperature control circuit is used to regulate the temperature. Figure shows the temperature control circuit using thermostat as temperature detector and SCR as ... half-cycle and heater gets connected to source to produce heat and raise the temperature.

Description : Compare SCR and TRIAC

Last Answer : SCR TRIAC It is an unidirectional device. It is a bidirectional device. It is turned-on by only positive gate current. It can be turned-on by either ... applications including lamp dimmer, heating control, zero voltage switched AC relay, small AC motor control etc.

Description : Describe triggering of SCR using UJT relaxation oscillator. 

Last Answer : I need it's operation

Description : How GTO is advantages over SCR

Last Answer : i) It is turned-off by negative gate pulse. ii) No commutation circuit required, reducing the cost, size, weight and volume of the circuit. iii) As commutation choke is not used, the associated acoustic ... turn off time permits high switching frequency. v) It has higher di/dt rating at turn-off. 

Description : Draw a neat labelling V-I characteristics of SCR and explain the region

Last Answer : (i) Latching current: It is the minimum anode current required to maintain the SCR in the conduction state just after turn-on and the gate signal has been removed.  (ii) Holding current: It is the minimum anode current required to hold the conducting SCR in the ON state. 

Description : Draw construction of SCR using two transistor model. Explain its operation.

Last Answer : Two Transistor Model of SCR or Thyristor

Description : SCR is more utilized as compared to Triac because it is

Last Answer : SCR is more utilized as compared to Triac because it is available with higher ratings

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Description : An SCR without any external connections is considered as (A) two diodes in series (B) three diodes in series (C) two n-p-n transistors in series (D) two p-n-p transistors in series

Last Answer : An SCR without any external connections is considered as three diodes in series

Description : Why SCR is called as thyristor?

Description : Is a SCR a thyristor?

Last Answer : Yes, SCR is a thyristor. Thyristor is the family and SCR is the member of that family but SCR is universally known as thyristor.

Last Answer : Yes, SCR is a unidirectional switch.

Description : What is the use of SCR?

Last Answer : SCR are use in lamp dimming, power regulators, motor control, rectifications of high power AC, control of welding machines and also use as switch these are some uses of silicon controlled rectifier.

Description : Is an anode positive or negative?

Last Answer : The anode is positively charged electrode.

Description : What is the difference between an anode and a cathode?

Last Answer : The anode is positively charged electrode and the cathode is negatively charged electrode.

Description : Do electrons flow from the anode to the cathode?

Last Answer : electrons flow from cathode to anode because the electron has a negative charge and repels from the negatively charged cathode whilst also attracting to the positively charged anode.

Description : Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Last Answer : The integral cycle control (on-off control) and phase angle control are the two types of AC voltage controller. The principle of ON-OFF control: The on-off control is also called an integral cycle ... control. In phase control, the switch is on for some period of each cycle.  

Description : A 100-watt light bulb turned on for 8 hours uses :  (A) 800 Wh (B) 0.8 kWh (C) 8 kWh (D) None of the above

Last Answer : A 100-watt light bulb turned on for 8 hours uses :  (A) 800 Wh (B) 0.8 kWh (C) 8 kWh (D) None of the above

Description : Purpose of Selective Catalytic Reduction (SCR)

Last Answer : Purpose of Selective Catalytic Reduction (SCR) : 1. It reduces Nox 75% to 90% 2. Converts it in to molecular nitrogen and water vapor 3. It reduces HC emission up to 80% 4. It reduces PM emission 20 to 25%.

Description : An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

Last Answer : An inductor is connected in series with SCR to protect it from Excessive high di/dt

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Description : How do you test an SCR?

Description : Why is pulse train gating preferred over pulse gating? Explain with relevant circuit and waveforms, the pulse train gating of SCRs.

Description : Define pinch off voltage and drain resistance of FET.

Last Answer : 1 . Pinch-off Voltage: It is the value of the drain to source voltage VDS at which the drain current ID reaches its constant saturation value. Any further increase in VDS does not have any ... drain to source voltage to the change in drain current. It is also called AC/dynamic drain resistance.

Last Answer : The fuse blows off by melting.

Description : What is meant by pinch off voltage in MOSFET?