Where is the throttle body spacer located?

Where is the throttle body spacer located?
by

1 Answer

Answer :

The throttle body spacer is a small piece of metal that is attached the back of a throttle body. It is suppose to change the airflow which can potentially give you more horsepower and better fuel economy.
by

Related questions

where can I purchase a body throttle spacer?

Description : where can I purchase a body throttle spacer?

Last Answer : You can buy a body throttle spacer on the internet, at your dealership or in a garage, all depends on your preferences. To be sure you get one that you will be satisfied with, you could ... the internet before making your selection, that way, you'll make the most informed decisions when you buy.

is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Description : is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Last Answer : Bearing.

A lever, which operates the gang mechanism of the disk harrow, is called the i. Spanners lever. c) spacer lever ii. Gang control lever. d) Bearing lever

Description : A lever, which operates the gang mechanism of the disk harrow, is called the i. Spanners lever. c) spacer lever ii. Gang control lever. d) Bearing lever

Last Answer : Gang control lever

Reflex bronchoconstriction is most likely to occur with the following form of inhaled antiasthma medication: A. Metered dose spray of drug in solution B. Dry powder rotacap C. Nebuliser D. Nebuliser with spacer

Description : Reflex bronchoconstriction is most likely to occur with the following form of inhaled antiasthma medication: A. Metered dose spray of drug in solution B. Dry powder rotacap C. Nebuliser D. Nebuliser with spacer

Last Answer : B. Dry powder rotacap

how to clean electronic throttle body on 2008 dodge caliber

Description : how to clean electronic throttle body on 2008 dodge caliber

Last Answer : Need Answer

What are the steps in resetting security lock out mode and can effect fuel reaching the throttle body?

Description : What are the steps in resetting security lock out mode and can effect fuel reaching the throttle body?

Last Answer : Just like The problem with this system is that at times it decreases throttle. For example, ECM reset does not clear the historical faults records.Step 1 Open the fuse panel in the driver-side foot well ... The ECU just resets itself back into the learning mode, I make a point to reset the ECU

D-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Description : D-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Last Answer : Answer: b Explanation: D-MPFI system uses direct injection and L-MPFI system uses port injection while multipoint fuel injection system uses port injection and throttle body injection.

L-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Description : L-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Last Answer : Answer: a Explanation: L-MPFI system uses port injection while multi-point fuel injection system uses port injection and throttle body injection while D-MPFI system uses direct injection.

Compare throttle body injection with port fuel injection systems.

Description : Compare throttle body injection with port fuel injection systems.

Last Answer : Sr. No. TBI system PFI System 1 Fuel is injected into the center of the throttle body. Fuel is injected into the port 2 TBI uses bottom feed ... the throttle body. Hither power output due to low resistance at intake manifold and higher volumetric efficiency.

Explain the construction and working of throttle body injection (TBI) system.

Description : Explain the construction and working of throttle body injection (TBI) system. 

Last Answer : The throttle body injection (TBI) system uses one or two injector valves mounted in a throttle body assembly. The injectors spray fuel into the top of the throttle body air horn The TBI fuel ... are then used to calculate the triggering signals for the injectors and other system actuators.  

When I close the throttle on my car, and allow speed to bleed off, is this a Delta-V scalar?

Description : When I close the throttle on my car, and allow speed to bleed off, is this a Delta-V scalar?

Last Answer : answer:So long as you travel in a straight line. As you probably know, turning is a change in velocity ( ΔV ) even if speed remains constant. However, if direction does not change then any ΔV ... and direction; a scalar and a vector, and we've alread declared the vector component to be constant.

the throttle stops working while driving

Description : audi A3 8l 1.8 t 110kw Hello, I started to have an unpleasant anomaly on the car. When driving, it happens to me (completely irregularly sometimes in 15 minutes of driving, sometimes in 4 hours) ... never happened to me that the car always wants the same scenario is repeated . Thank you in advance

Last Answer : look here you could have the same https://www.club-opel.cz/viewtopic.php?f=150&t=276

assemble the throttle for a mercury optimax

Description : assemble the throttle for a mercury optimax

Last Answer : Need Answer

What will a bad throttle positoning sensor do in a 95 jeep grand Cherokee?

Description : What will a bad throttle positoning sensor do in a 95 jeep grand Cherokee?

Last Answer : Feel Free to Answer

Is the throttle on the right side or the left side of the motorcycle?

Description : Is the throttle on the right side or the left side of the motorcycle?

Last Answer : The throttle is on the right handlebar grip. Your brakes are the levers on each handlebar, the front brake is on the right and the rear brake is on the left.

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Description : In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Last Answer : Ans: b

In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: d

In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: c

In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Last Answer : Ans: a

In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Description : In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Last Answer : Answer: d Explanation: None.

The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: d Explanation: The knock sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded while the camshaft position sensor, senses ... the engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: c Explanation: The camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection whereas the throttle position sensor, senses the movement of the throttle ... engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: b Explanation: The manifold pressure sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load and the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.

The _____________ sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: a Explanation: The throttle position sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration while the manifold ... the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.

Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Description : Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Last Answer : Answer: A

The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the throttle control circuit B. feedback resistor of the summing amplifier circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Description : On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Last Answer : Answer: B

6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Description : 6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (C) Merely compressing it beyond critical pressure

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively (A) Decreases & increases (B) Increases & increases (C) Increases & decreases (D) Decreases & decreases

Description : When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively (A) Decreases & increases (B) Increases & increases (C) Increases & decreases (D) Decreases & decreases

Last Answer : (A) Decreases & increases

A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the inversion is 090/30. What is the safest departure procedure? a. Take-off is not possible under these conditions b. Depart on runway 09 with a tailwind c. Depart runway 27 with maximum throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Description : A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an  inversion is reported at 300 feet with turbulence and wind shear. The wind just above the  ... throttle during the passage through the inversion  d. Depart runway 27 with as steep an ascent as possible

Last Answer : b. Depart on runway 09 with a tailwind

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the inversion is 090/30. What is the safest departure procedure? a. Take-off is not possible under these conditions b. Depart on runway 09 with a tailwind c. Depart runway 27 with maximum throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Description : A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the ... throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Last Answer : b. Depart on runway 09 with a tailwind

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

Name the sensors which are placed at intake manifold ,throttle valve, water jacket and exhaust manifold.

Description : Name the sensors which are placed at intake manifold ,throttle valve, water jacket and exhaust manifold. 

Last Answer : Sensors: Intake manifolds:- Mass air flow sensor (MAF), Manifold absolute pressure sensor (MAP) Throttle valve:- Throttle position sensor (TPS) Water jacket:- Engine temperature sensor or coolant temperature sensor Exhaust manifolds: - Exhaust gas temperature sensor, Oxygen sensor (O2)