the throttle stops working while driving

audi A3 8l 1.8 t 110kw Hello, I started to have an unpleasant anomaly on the car. When driving, it happens to me (completely irregularly sometimes in 15 minutes of driving, sometimes in 4 hours) when I change to a higher quality so the car stops responding to gas and I have no choice but to finish with the car and stop playing, then I grab it and start again for the first time and the car runs like nothing. it happens during a quiet ride of 2500-3000 rpm. but also at 4000+. after I stop the engine idles and when I hold full throttle the speed runs to 1800 and immediately drops below 1000 the engine makes a sound like it should snag but catches idle speed and after a while this repeats (I keep the throttle all the time. I tried I manually add gas through the throttle but the result is the same.Yeah and I have a blow-off valve on the car ... I wondered if it would not release too much pressure .... so far it has never happened to me that the car always wants the same scenario is repeated . Thank you in advance
by

1 Answer

Answer :

look here you could have the same https://www.club-opel.cz/viewtopic.php?f=150&t=276
by

Related questions

Explain the construction and working of throttle body injection (TBI) system.

Description : Explain the construction and working of throttle body injection (TBI) system. 

Last Answer : The throttle body injection (TBI) system uses one or two injector valves mounted in a throttle body assembly. The injectors spray fuel into the top of the throttle body air horn The TBI fuel ... are then used to calculate the triggering signals for the injectors and other system actuators.  

What should be done if an air conditioner stops working, instead of getting rid of it or calling an expert?

Description : What should be done if an air conditioner stops working, instead of getting rid of it or calling an expert?

Last Answer : What are you asking? Maybe call your cousin Bob to see if he can fix it? Find a tutorial on YouTube? I’m not sure what you want to know, here.

Can the solar panel on an outdoor solar light be replaced if it stops working?

Description : Can the solar panel on an outdoor solar light be replaced if it stops working?

Last Answer : Not really, and it would be cheaper to get a new one. Not worth the trouble to replace it, I've taken apart loads of these things. Solar panels really don't stop working anyways, unless you ... power to them, the only thing is tha tperformance decreases when there's dust on them so keep it clean

You know about those RETRACTABLE pen drives? Does anyone know how to get this type of pen drive working again once it suddenly stops working?

Description : You know about those RETRACTABLE pen drives? Does anyone know how to get this type of pen drive working again once it suddenly stops working?

Last Answer : Is the drive recognized at all? Try it in another computer, if it’s still not working it may be fried.

My bike stops working when it gets below freezing...

Description : My bike stops working when it gets below freezing...

Last Answer : It may depend on the type of chain lube used to grease your chain. There are some that work way better than others in cold weather. Same for the lube on all parts related to moving the bike - the pedal threads ... 's a $20 bike. Why would it work in the first place? But really, it could be the lube.

when an individual stops working out, muscles slowly __________. -General Knowledge

Description : when an individual stops working out, muscles slowly __________. -General Knowledge

Last Answer : C. lose strength.

Phone xiaomi note 7mi reports every 5 seconds: google application periodically stops working. I have no idea what I'm doing. Thank you

Description : Phone xiaomi note 7 reports to me every 5 seconds: google periodically stops working. I have no idea what I'm doing. I've already removed the update here, but it didn't help.

Last Answer : Need Answer

What would happen if my laptop fan stops working?

Description : What would happen if my laptop fan stops working?

Last Answer : If Laptop fan stops working then following things will happen: 1. CPU can overheat beyond its working temperature. 2. Overheated CPU can heat up further and can damage Motherboard and connected components such as USB, Charging Jack etc.

If the engine of a motor car moving up with an angle of 45 slope with a speed of 63kmh stops working suddenly how car move before coming to rest if it weighs 19600 and frictional force is 2000?

Description : If the engine of a motor car moving up with an angle of 45 slope with a speed of 63kmh stops working suddenly how car move before coming to rest if it weighs 19600 and frictional force is 2000?

Last Answer : Need answer

If my dvd player stops working, what can i do?

Description : If my dvd player stops working, what can i do?

Last Answer : First, check to see if all of your wires are plugged in this includes your power cord. Then check to see if your dvd is scratched or upside down. If these do not work try looking into problems with your television.

Fines are not working at keeping people from using their cell phones while driving, should the penalty be jail time if caught using a cell phone while driving?

Description : Fines are not working at keeping people from using their cell phones while driving, should the penalty be jail time if caught using a cell phone while driving?

Last Answer : the only answer to your last question is they are stupid.

When I close the throttle on my car, and allow speed to bleed off, is this a Delta-V scalar?

Description : When I close the throttle on my car, and allow speed to bleed off, is this a Delta-V scalar?

Last Answer : answer:So long as you travel in a straight line. As you probably know, turning is a change in velocity ( ΔV ) even if speed remains constant. However, if direction does not change then any ΔV ... and direction; a scalar and a vector, and we've alread declared the vector component to be constant.

how to clean electronic throttle body on 2008 dodge caliber

Description : how to clean electronic throttle body on 2008 dodge caliber

Last Answer : Need Answer

assemble the throttle for a mercury optimax

Description : assemble the throttle for a mercury optimax

Last Answer : Need Answer

What will a bad throttle positoning sensor do in a 95 jeep grand Cherokee?

Description : What will a bad throttle positoning sensor do in a 95 jeep grand Cherokee?

Last Answer : Feel Free to Answer

Is the throttle on the right side or the left side of the motorcycle?

Description : Is the throttle on the right side or the left side of the motorcycle?

Last Answer : The throttle is on the right handlebar grip. Your brakes are the levers on each handlebar, the front brake is on the right and the rear brake is on the left.

Where is the throttle body spacer located?

Description : Where is the throttle body spacer located?

Last Answer : The throttle body spacer is a small piece of metal that is attached the back of a throttle body. It is suppose to change the airflow which can potentially give you more horsepower and better fuel economy.

where can I purchase a body throttle spacer?

Description : where can I purchase a body throttle spacer?

Last Answer : You can buy a body throttle spacer on the internet, at your dealership or in a garage, all depends on your preferences. To be sure you get one that you will be satisfied with, you could ... the internet before making your selection, that way, you'll make the most informed decisions when you buy.

What are the steps in resetting security lock out mode and can effect fuel reaching the throttle body?

Description : What are the steps in resetting security lock out mode and can effect fuel reaching the throttle body?

Last Answer : Just like The problem with this system is that at times it decreases throttle. For example, ECM reset does not clear the historical faults records.Step 1 Open the fuse panel in the driver-side foot well ... The ECU just resets itself back into the learning mode, I make a point to reset the ECU

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Description : In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Last Answer : Ans: b

In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: d

In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: c

In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Last Answer : Ans: a

In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Description : In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Last Answer : Answer: d Explanation: None.

The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: d Explanation: The knock sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded while the camshaft position sensor, senses ... the engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: c Explanation: The camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection whereas the throttle position sensor, senses the movement of the throttle ... engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: b Explanation: The manifold pressure sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load and the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.

The _____________ sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: a Explanation: The throttle position sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration while the manifold ... the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.

D-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Description : D-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Last Answer : Answer: b Explanation: D-MPFI system uses direct injection and L-MPFI system uses port injection while multipoint fuel injection system uses port injection and throttle body injection.

L-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Description : L-MPFI system uses a) port injection b) direct injection c) manifold injection d) throttle body injection

Last Answer : Answer: a Explanation: L-MPFI system uses port injection while multi-point fuel injection system uses port injection and throttle body injection while D-MPFI system uses direct injection.

Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Description : Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Last Answer : Answer: A

The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the throttle control circuit B. feedback resistor of the summing amplifier circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Description : On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Last Answer : Answer: B

6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Description : 6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (C) Merely compressing it beyond critical pressure

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively (A) Decreases & increases (B) Increases & increases (C) Increases & decreases (D) Decreases & decreases

Description : When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively (A) Decreases & increases (B) Increases & increases (C) Increases & decreases (D) Decreases & decreases

Last Answer : (A) Decreases & increases

A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the inversion is 090/30. What is the safest departure procedure? a. Take-off is not possible under these conditions b. Depart on runway 09 with a tailwind c. Depart runway 27 with maximum throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Description : A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an  inversion is reported at 300 feet with turbulence and wind shear. The wind just above the  ... throttle during the passage through the inversion  d. Depart runway 27 with as steep an ascent as possible

Last Answer : b. Depart on runway 09 with a tailwind

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the inversion is 090/30. What is the safest departure procedure? a. Take-off is not possible under these conditions b. Depart on runway 09 with a tailwind c. Depart runway 27 with maximum throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Description : A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the ... throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Last Answer : b. Depart on runway 09 with a tailwind

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

Compare throttle body injection with port fuel injection systems.

Description : Compare throttle body injection with port fuel injection systems.

Last Answer : Sr. No. TBI system PFI System 1 Fuel is injected into the center of the throttle body. Fuel is injected into the port 2 TBI uses bottom feed ... the throttle body. Hither power output due to low resistance at intake manifold and higher volumetric efficiency.

Name the sensors which are placed at intake manifold ,throttle valve, water jacket and exhaust manifold.

Description : Name the sensors which are placed at intake manifold ,throttle valve, water jacket and exhaust manifold. 

Last Answer : Sensors: Intake manifolds:- Mass air flow sensor (MAF), Manifold absolute pressure sensor (MAP) Throttle valve:- Throttle position sensor (TPS) Water jacket:- Engine temperature sensor or coolant temperature sensor Exhaust manifolds: - Exhaust gas temperature sensor, Oxygen sensor (O2)

You are a bus driver at a station. 10 get on the bus and no one gets off. You drive 10 miles to another station where 3 people get on and 1 gets off. You drive another 10 miles only to get 25 people on and 5 people go off. Next you drive 3 miles while 12 people exit the bus. You drive back to the place knowing that a couple more stops along the way untill the ride is done. At the 2nd to last station 5 people get on and 2 get off. And at the last station (5.5 miles) 25 people get on for no reason and 1 gets off. What is the bus drivers eye color? -Riddles

Description : You are a bus driver at a station. 10 get on the bus and no one gets off. You drive 10 miles to another station where 3 people get on and 1 gets off. You drive another 10 miles only to get 25 ... 5 miles) 25 people get on for no reason and 1 gets off. What is the bus drivers eye color? -Riddles

Last Answer : Brown/blue/green (i don't know how i would put it though so if you guessed your eye color you got it right :) )

When driving in your car, can you tell when something is not working right or about to break?

Description : When driving in your car, can you tell when something is not working right or about to break?

Last Answer : Probably your sense of hearing. You probably detect subtle differences in the sound of the engine.

Would it be inappropriate to mention to the person conducting my road test that I have been working through an extreme phobia of driving?

Description : Would it be inappropriate to mention to the person conducting my road test that I have been working through an extreme phobia of driving?

Last Answer : answer:It's not that it would be inappropriate , it just wouldn't (and shouldn't) matter. Driving examiners are used to first-time drivers being nervous about passing. That's part of what they deal ... is a very patient and good driver - and have that person play the part of the examiner with you.