Cetane number is a measure of a. ignition quality b. addition in fuel c. calorific value of fuel d. viscosity of the fuel

Cetane number is a measure of  a. ignition quality  b. addition in fuel  c. calorific value of fuel  d. viscosity of the fuel  
by

1 Answer

Answer :

ANSWER  a. ignition quality
by
selected by

Related questions

Ignition quality of diesel is expressed by a. octane number b. cetane number c. calorific value d. carbon content

Description : Ignition quality of diesel is expressed by a. octane number b. cetane number c. calorific value d. carbon content

Last Answer : ANSWER b. cetane number

Ignition quality of petrol is expressed by a. Octane number b. cetane number c. calorific value d. self-ignition temperature

Description : Ignition quality of petrol is expressed by a. Octane number b. cetane number c. calorific value d. self-ignition temperature

Last Answer : ANSWER a. Octane number

A fuel of cetane number 40 has the same ignition quality as a mixture of a) 40% cetane and 60% alpha methyl naphthalene b) 40% alpha methyl naphthalene and 60% cetane c) 40% petrol and 60% diesel d) 40% diesel and 60% petrol

Description : A fuel of cetane number 40 has the same ignition quality as a mixture of a) 40% cetane and 60% alpha methyl naphthalene b) 40% alpha methyl naphthalene and 60% cetane c) 40% petrol and 60% diesel d) 40% diesel and 60% petrol

Last Answer : Answer: a Explanation: A fuel of cetane number 40 has the same ignition quality as a mixture of 40% cetane and 60% alpha methyl naphthalene as cetane number is counted on cetane percentage.

Cetane number of a diesel fuel is the measure of its (A) Ignition delay (B) Smoke point (C) Viscosity (D) Oxidation stability

Description : Cetane number of a diesel fuel is the measure of its (A) Ignition delay (B) Smoke point (C) Viscosity (D) Oxidation stability

Last Answer : (A) Ignition delay

The self-ignition temperature of diesel oil compared to petrol is a. higher b. lower c. same d. depends on the quality of fuel

Description : The self-ignition temperature of diesel oil compared to petrol is a. higher b. lower c. same d. depends on the quality of fuel

Last Answer : ANSWER a. higher

The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased

Description : The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased

Last Answer : ANSWER d. compression ratio is increased

The two reference fuel used for cetane rating are (a) Cetane and iso octane (b) Cetane and tetra ethyl lead (c) Cetance and n-heptane (d) Cetane and α- methyl naphthalene

Description : The two reference fuel used for cetane rating are (a) Cetane and iso octane (b) Cetane and tetra ethyl lead (c) Cetance and n-heptane (d) Cetane and α- methyl naphthalene

Last Answer : Ans : d

By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Description : By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Last Answer : Ans : d

The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. all of the above

Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. all of the above

Last Answer : ANSWER d. all of the above

The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. All of the above

Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. All of the above

Last Answer : ANSWER d. all of the above

An engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the calorific value of the fuel used is 40000 kJ/kg, then what is the fuel consumption? (a) 1.5 kg/hour (b) 3 kg/hour (c) 0.3 kg/hour (d) 1 kg/hour

Description : An engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the calorific value of the fuel used is 40000 kJ/kg, then what is the fuel consumption? (a) 1.5 kg/hour (b) 3 kg/hour (c) 0.3 kg/hour (d) 1 kg/hour

Last Answer : Ans :b

All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Description : All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Last Answer : ANSWER a. lower heating value of oil

The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Description : The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Last Answer : Ans :c

Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Description : Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Last Answer : ANSWER a. rate of injection of fuel

Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Description : Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Last Answer : ANSWER d. all of the above

The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Description : The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Last Answer : ANSWER d. all the above

A mixture containing 65% of iso-octane and 35% of normal heptane will have a) cetane number 65 b) octane number 65 c) cetane number 35 d) octane number 35

Description : A mixture containing 65% of iso-octane and 35% of normal heptane will have a) cetane number 65 b) octane number 65 c) cetane number 35 d) octane number 35

Last Answer : Answer: b Explanation: A mixture containing 65% of iso-octane and 35% of normal heptane will have octane number 65 as octane number is the number percentage containing iso-octane.

Cetane number of petrol is around a. 10 b. 15-20 c. 35 d. 55-70

Description : Cetane number of petrol is around a. 10 b. 15-20 c. 35 d. 55-70

Last Answer : ANSWER b. 15-20

For the best results of efficient combustion, high speed diesel engines need an approximate cetane number of a. 100 b. 50 c. 10 d. 5

Description : For the best results of efficient combustion, high speed diesel engines need an approximate cetane number of a. 100 b. 50 c. 10 d. 5

Last Answer : ANSWER b. 50

The optimum percentage of excess air for combustion depends upon the__________ of the fuel.(A) Type (solid, liquid or gaseous)(B) Calorific value(C) Sulphur content(D) Ignition temperature

Description : The optimum percentage of excess air for combustion depends upon the__________ of the fuel. (A) Type (solid, liquid or gaseous) (B) Calorific value (C) Sulphur content (D) Ignition temperature

Last Answer : (A) Type (solid, liquid or gaseous)

Which of the following statement is incorrect?  A. The liquid fuels consist of hydrocarbons.  B. The liquid fuels have higher calorific value than solid fuels.  C. The solid fuels have higher calorific value than liquid fuels.  D. A good fuel should have low ignition point.

Description : Which of the following statement is incorrect?  A. The liquid fuels consist of hydrocarbons.  B. The liquid fuels have higher calorific value than solid fuels.  C. The solid fuels have higher calorific value than liquid fuels.  D. A good fuel should have low ignition point.

Last Answer : Answer: C

The most important property for a jet fuel is its (A) Viscosity (B) Freezing point (C) Calorific value (D) Flash poin

Description : The most important property for a jet fuel is its (A) Viscosity (B) Freezing point (C) Calorific value (D) Flash poin

Last Answer : (B) Freezing point

The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period

Description : The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period

Last Answer : ANSWER : A

Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Last Answer : ANSWER : A

In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Description : In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Last Answer : ANSWER : C

Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Last Answer : ANSWER : C

The accumulation of carbon in a cylinder results in increase of A. clearance volume B. volumetric efficiency C. ignition time D. effective compression ratio

Description : The accumulation of carbon in a cylinder results in increase of A. clearance volume B. volumetric efficiency C. ignition time D. effective compression ratio

Last Answer : ANSWER : D

In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)

The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Description : The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Last Answer : Which of the following is not true for two stroke engine as compared to four stroke engine? a. Less cooling is required b. Greater lubrication is required c. More uniform torque on crankshaft d. Complete exhaust of products of combustion (Ans:a)

In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Description : In spark ignition engines, the knocking tendency can be decreased by a) decreasing compression ratio b) controlling intake throttle c) controlling ignition timing d) adding dopes like tetraethyl lead and ethylene dibromide

Last Answer : Answer: d Explanation: None.

Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned

Description : Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned

Last Answer : Answer: c Explanation: None.

The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: d Explanation: The knock sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded while the camshaft position sensor, senses ... the engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

Anti-knock for compression ignition engines is a) napthene b) tetra ethyl lead c) amyl nitrate d) hexadecane

Description : Anti-knock for compression ignition engines is a) napthene b) tetra ethyl lead c) amyl nitrate d) hexadecane

Last Answer : Answer: c Explanation: Amyl nitrate is the anti-knock for compression ignition engines.

The accumulation of carbon in a cylinder results in increase of a. clearance volume b. volumetric efficiency c. ignition time d. effective compression ratio

Description : The accumulation of carbon in a cylinder results in increase of a. clearance volume b. volumetric efficiency c. ignition time d. effective compression ratio

Last Answer : ANSWER d. effective compression ratio

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Last Answer : ANSWER c. Both a and b.

In compression ignition engines, swirl denotes a. Haphazard motion of the gases in the cylinder b. Rotary motion of the gases in the cylinder. c. Radial motion of the gases in the cylinder. d. None of the above

Description : In compression ignition engines, swirl denotes a. Haphazard motion of the gases in the cylinder b. Rotary motion of the gases in the cylinder. c. Radial motion of the gases in the cylinder. d. None of the above

Last Answer : ANSWER a. Haphazard motion of the gases in the chamber

Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Description : Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Last Answer : ANSWER b. compression ignition engine

Self-ignition temperature of petrol is of the order of a. 150 C b. 240 C c. 370 C d. more than 500 C

Description : Self-ignition temperature of petrol is of the order of a. 150 C b. 240 C c. 370 C d. more than 500 C

Last Answer : ANSWER d. more than 500 C

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Last Answer : ANSWER c. Both a and b

Combustion in compression ignition engine is a. homogeneous b. heterogeneous c. laminar d. turbulent

Description : Combustion in compression ignition engine is a. homogeneous b. heterogeneous c. laminar d. turbulent

Last Answer : ANSWER b. heterogeneous

For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Description : For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Last Answer : ANSWER (B) for both idling and peak power conditions

A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel cycle is higher than the Otto cycle, at a fixed compression ratio c. The compression ratio of a diesel engine is higher than that of an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Description : A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel ... an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Last Answer : ANSWER c. The compression ratio of a diesel engine is higher than that of an S.I engine

The self-ignition temperature of diesel as compared to petrol is a. higher b. lower c. same d. varies

Description : The self-ignition temperature of diesel as compared to petrol is a. higher b. lower c. same d. varies

Last Answer : ANSWER a. higher

Which of the following cycle is used for Compression Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : Which of the following cycle is used for Compression Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer b. Diesel cycle

Which of the following cycle is used for Spark Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : Which of the following cycle is used for Spark Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer a. Otto cycle

Straight run petrol as compared to methyl/ethyl alcohol has (A) Lower calorific value (B) Lower octane number (C) Higher specific gravity (D) Higher ignition temperature

Description : Straight run petrol as compared to methyl/ethyl alcohol has (A) Lower calorific value (B) Lower octane number (C) Higher specific gravity (D) Higher ignition temperature

Last Answer : (B) Lower octane number

Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has (A) High pour point and low smoke point (B) Low viscosity index (C) High self-ignition temperature (D) All (A), (B) and (C)

Description : Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has (A) High pour point and low smoke point (B) Low viscosity index (C) High self-ignition temperature (D) All (A), (B) and (C)

Last Answer : (B) Low viscosity index

For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Description : For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Last Answer : (A) High volatile matter

A coal having higher volatile matter content will necessarily have lower (A) Ash fusion temperature (B) Calorific value (C) Ignition temperature (D) Caking index

Description : A coal having higher volatile matter content will necessarily have lower (A) Ash fusion temperature (B) Calorific value (C) Ignition temperature (D) Caking index

Last Answer : (C) Ignition temperature