To limit the operating temperature an electrical machine should have proper?

by

1 Answer

Answer :

To limit the operating temperature an electrical machine should have proper current rating.

by

Related questions

Electrical specifications with values for washing machine.

Description : Electrical specifications with values for washing machine. 

Last Answer : 1. Type: Top loading / Front loading type 2. Capacity range: 6kg to 15kg 3. Motor Used: Induction motor 4. Input voltage: 100V- 240V 5. Power: in 1200W / Output power 100–400W{can go upto 1000W) 6. Efficiency: Max efficiency 31% 7. Wattage: 2.100-2.400 W 8. Current: 13A 9. Frequency: 50hz

The operating speed of a synchronous motor can be changed to new fixed value by?

Last Answer : The operating speed of a synchronous motor can be changed to new fixed value by changing frequency.

The steady state stability limit as compared to the transient state stability limit is always

Description : The steady state stability limit as compared to the transient state stability limit is always

Last Answer : The steady state stability limit as compared to the transient state stability limit is always Greater

Which of the following statements is true? steady-state stability limit is greater than transient stability limit

Description : Which of the following statements is true?  (1) steady-state stability limit is greater than transient stability limit  (2) steady-state stability limit is equal to transient stability ... made regarding the equality or otherwise of the steady-state stability limit and transient stability limit

Last Answer : Which of the following statements is true?  (1) steady-state stability limit is greater than transient stability limit  (2) steady-state stability limit is equal to transient ... made regarding the equality or otherwise of the steady-state stability limit and transient stability limit

Synchronsizing power of a synchronous machine is?

Last Answer : Synchronsizing power of a synchronous machine is inversely proportional to the synchronous reactance.

A synchronous machine with low value of short-circuit ratio has?

Last Answer : A synchronous machine with low value of short-circuit ratio has lower stability limit.

If we change the excitation of synchronous machine will it affect on power factor?

Description : If we change the excitation of synchronous machine will it affect on power factor?

Last Answer : Yes, If we change the excitation of synchronous machine it will affect on power factor. If the synchronous motor is overexcited then it will have leading power factor and if the motor is underexcited then it will have lagging power factor.

If we change the excitation of synchronous machine will it affect on motor speed?

Description : If we change the excitation of synchronous machine will it affect on motor speed?

Last Answer : No, If we change the excitation of synchronous machine it will not affect on motor speed.

V - curve of synchronous machine shows the relation between?

Description : V - curve of synchronous machine shows the relation between?

Last Answer : V - curve of synchronous machine shows the relation between AC armature current and DC field current.

Why synchronous machine is called doubly excited machine?

Description : Why synchronous machine is called doubly excited machine?

Last Answer : Armature windings of synchronous machines either deliver 3 phase AC or absorb 3 phase AC source,  whereas field windings are energized from DC source. Thus due to presence of AC on armature and DC on field windings, synchronous machines are often referred as doubly excited machines.

Which machine is the exciter of synchronous machine?

Description : Which machine is the exciter of synchronous machine?

Last Answer : DC shunt machine is the exciter of synchronous machine.

Write down the basic parts of a lathe machine with their proper functions.

Description : Write down the basic parts of a lathe machine with their proper functions. 

Last Answer : Important Parts of Lathe and their Functions 1. Bed It is the main body of the machine. All main components are bolted on it. It is usually made by cast iron due to its high compressive strength and ... carriage on bed. 12. Spindle: It is the main part of lathe which holds and rotates the chuck.

How to Uninstall an Operating System ?

Description : How to Uninstall an Operating System ?

Last Answer : How to Uninstall an Operating System Even the most stable operating systems can crash, and suffer from irreparable damage that you may need to uninstall and reinstall them. Some users, though, may like to ... , you can easily remove the old, damaged operating system, and replace it with a new one.

operating principle of PUT.

Description :  operating principle of PUT.

Last Answer : Constructional diagram & Operating principle of PUT:  The PUT is a PNPN device similar to SCR, but its operation is similar to the UJT. The PUT behave like a UJT whose trigger voltage VP can be set ... low resistance and VAK ≈ 1V). The PUT is also referred to as a complementary SCR (CSCR). 

Transistor operating configurations

Description : Transistor operating configurations

Last Answer : Transistor operating configurations

Draw construction of Megger and write operating principle of it.

Description : Draw construction of Megger and write operating principle of it.

Last Answer : Megger:  Working: Two coils the current coil and pressure coil are mounted at an angle on the same spindle and form the part of the moving system. These coils are connected to a small hand driven ... . When the instrument is not working the pointer may rest at any position on the dial.

Explain the operating principle of LASER and list applications of LASER diode.

Description : Explain the operating principle of LASER and list applications of LASER diode.

Last Answer : A basic construction of Laser diode is as shown . A PN junction is formed by two layers of doped gallium arsenide. There is highly reflective surface at one end of PN junction and ... 6. laser scanning and light beam illumination. 7. Military applications 8. Medical surgery 9.Diamond cutting

The command line interpreter that enables the users to interact with operating system is called the

Description : The command line interpreter that enables the users to interact with operating system is called the A) Window B) Shell C) Process D) Kernel 

Last Answer : The command line interpreter that enables the users to interact with operating system is called the Shell 

The operating point of a protective current transformer is near the

Description : The operating point of a protective current transformer is near the

Last Answer : The operating point of a protective current transformer is near the Ankle point

The operating time of instantaneous relay is

Description : The operating time of instantaneous relay is

Last Answer : The operating time of instantaneous relay is 0.1 sec

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Last Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

In a single-phase induction motor, the operating direction is determined by the ________

Description : In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

Last Answer : In a single-phase induction motor, the operating direction is determined by the Starting circuit

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016

Description : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last Answer : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power

Description : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, ... system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

Last Answer : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is 50 Hz

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

Operating torques in analogue instruments are?

Last Answer : Operating torques in analogue instruments are deflecting, control and damping.

The operating voltage of a meggar is about?

Last Answer : The operating voltage of a meggar is about 100 V.

Annual operating expenditure of a power plant consists of?

Last Answer : Annual operating expenditure of a power plant consists of fixed charges, semi-fixed charges, running charges.

The relay operating speed depends upon?

Last Answer : The relay operating speed depends upon the spring tension, the rate of flux built up, armature core air gap.

The secondary of a current transformer is always short-circuited under operating conditions because it?

Description : The secondary of a current transformer is always short-circuited under operating conditions because it?

Last Answer : The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

For a transformer, operating at constant load current, maximum efficiency will occur at?

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Last Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Description : Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Last Answer : Power MOSFET have high turning on and turning off capability high switching speed of MOSFET is due to the high rate of change of drain voltage. The switching losses of power MOSFET ... lower frequency. Hence, operating frequency of power MOSFET is higher than that of power BJT.

what are the three operating regions of BJT?

Last Answer : Active , Saturation , Cut-off region of operations in BJT.

What's the temperature in a Slurpee machine?

Description : What's the temperature in a Slurpee machine?

Last Answer : You’re in luck! The official Slurpee website says that the machines keep the drinks at 28 degrees (Sugar is the anti-freezing agent in most Slurpees).

What is the function of the roll forming machine ?

Description : What is the function of the roll forming machine ?

Last Answer : It is much easier to make croissants and other dinner rolls with a roll forming machine, than it is to roll the croissants by hand. The primary function, therefore, is to take the mixed dough and to thin it, then fold it, to prepare the dough for baking.

How to Repair a Washing Machine

Description : How to Repair a Washing Machine

Last Answer : How to Repair a Washing Machine One of the modern conveniences that most people cannot live without is their washing machine. Washing machines have become extremely commonplace in today's homes and while ... store for more information on fixing it, or whether it is worth replacing the entire unit.

How to Repair a Sewing Machine

Description : How to Repair a Sewing Machine

Last Answer : How to Repair a Sewing Machine As being one of the more heavy-duty appliances, sewing machines can provide many years of reliable use. Often they do need to be cleaned out due to the excess ... it does, you will have to increase the belt's tension by shifting the motor-mountain screws again.

How to Thread a Sewing Machine

Description : How to Thread a Sewing Machine

Last Answer : How to Thread a Sewing Machine So you finally found a pattern you want to sew. You've got your mom's trusty sewing machine out, but before you can start sewing away, you must first learn to thread the ... be an easy task. Soon, you'll be a whiz at threading a sewing machine and at sewing, too!

How to Clean a Washing Machine

Description : How to Clean a Washing Machine

Last Answer : How to Clean a Washing Machine You need a washing machine to clean all your clothes and have them smelling clean, so have you ever thought about what it takes to keep the actual machine clean? ... of the washing machine dry. Repeat cleaning the front load washing machine at least once a month.

10 Benefits of climber machine

Description : 10 Benefits of climber machine

Last Answer : 10 Benefits of climber machine The climber machine is tall, slim machine pinched away in the corner of the gym. Maybe you've seen someone on it apparently with his personal trainer in ferry. It's ... that will give more strength to the arms and legs and will increase the strength of the body too.

How to choose a rowing machine and how to use it?

Description : How to choose a rowing machine and how to use it?

Last Answer : Many people know that it is easy to calculate rowing athletes against the background of other people by a special article. The beauty of their figure is formed during rowing sessions, which provide an ... times for 10 minutes with 10-minute breaks, this will be tantamount to one 30-minute lesson.

Capsule coffee machine. What are the advantages?

Description : Capsule coffee machine. What are the advantages?

Last Answer : Having a coffee maker in the house helps us to easily cheer up and brighten up the beginning of the upcoming day in the morning, especially if the weather is unpleasant. A cup of hot ... favor is the fact that the profile of this manufacturer is precisely capsule coffee makers and coffee capsules.

How to choose a washing machine?

Description : How to choose a washing machine?

Last Answer : How to choose a washing machine? When choosing a washing machine, first of all, you need to think about the future location of its placement. According to what space you have, choose: ... occurs using a fairly simple method - the machine includes an additional rinse cycle. Enjoy the shopping!

Explain the basic parts of a slotting machine with neat sketch.

Description : Explain the basic parts of a slotting machine with neat sketch. 

Last Answer : Base or Bed The base is rigidly built to take up all the cutting forces and the entire load of the machine. The top of the bed is accurately finished to provide guideways on which ... return mechanism. 2. Variable speed reversible motor drive mechanism. 3. Hydraulic drive mechanism.

Write down the steps involved for internal thread cutting on lathe machine.

Description : Write down the steps involved for internal thread cutting on lathe machine.

Last Answer : Steps involved for internal thread cutting on lathe machine  1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on the boring bar adjusted the angle of ... the start. 10) Keep going until the calculated depth of cut has been reached on the top slide.

Types of slotting machine

Description : Types of slotting machine

Last Answer : 1. Puncher slotter 2. Precision slotter 3. Production slotter  Working Principle of Slotting machine:- The slotting machine is a reciprocating machine tool in which, The vertical slide holding the cutting ... longitudinal and cross feeds, a rotary feed motion is also provided in the work table. 

Define Feed and speed in shaping machine

Description : Define Feed and speed in shaping machine

Last Answer : 1) Feed: Feed (S) is the relative movement of the work or tool in a direction perpendicular to the axis of reciprocation of the ram per double stroke. It is expressed in mm per stroke. 2) Speed: ... speed is the speed at which the metal is removed by the cutting tool in a period of one minute.

Why poles of dc machine are laminated?

Description : Why poles of dc machine are laminated?

Last Answer : Poles of DC machines are laminated to reduce the eddy current losses in the poles.