892 views

1 Answer

Answer :

A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Like 0 like

Please log in or register to answer this question.

Related questions

229 views

Last Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

1 answer
281 views

Last Answer : In a single phase motor the centrifugal switch disconnects auxiliary winding of the motor.

1 answer
216 views

Last Answer : In a capacitor start motor, the phase displacement between starting and running winding can be nearly 90°.

1 answer
191 views

Last Answer : If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then Electrolytic capacitor will, in all probability, suffer break down.

1 answer
127 views

Last Answer : The starting winding of a single-phase motor is placed in stator.

1 answer
240 views

Last Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

1 answer
219 views

Last Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

1 answer
163 views

Description : The damping winding in synchronous motor is generally used to?

Last Answer : The damping winding in synchronous motor is generally used to provide starting torque and prevent hunting.

1 answer
147 views

Last Answer : In A.C. series motor compensating winding is employed to reduce sparking at the brushes.

1 answer
78 views

Last Answer : In split-phase motor auxiliary winding is of thin wire placed at the top of the slots.

1 answer
117 views

Description : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

Last Answer : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be at the slot edge where coil enters or comes out of the slot.

1 answer
106 views

Last Answer : In a split phase motor, the running winding should have low resistance and high inductance.

1 answer
102 views

Last Answer : The value of starting capacitor of a fractional horse power motor will be 300 uF .

1 answer
91 views

Last Answer : The rotor developed by a single-phase motor at starting is zero.

1 answer
3.4k views

Description : A _________ is used to measure the stator % winding temperature of the generator.  (A) Thermocouple (B) Pyrometer (C) Resistance thermometer (D) Thermometer

Last Answer : A Resistance thermometer is used to measure the stator % winding temperature of the generator. 

1 answer
358 views

Last Answer : In D.C. machines fractional pitch winding is used to reduce the sparking.

1 answer
203 views

Last Answer :  Sandwich type winding is used in 3 phase shell-type transformer.

1 answer
92 views

Description : Damper winding in a synchronous motor

Last Answer : Damper winding in a synchronous motor Serves to start the motor.

1 answer
358 views

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

1 answer
115 views

Last Answer : The purpose of stator winding in the compensated repulsion motor is to improve power factor and provide better speed regulation.

1 answer
87 views

Last Answer : In split phase motor main winding is of thick wire placed at the bottom of the slots.

1 answer
264 views

Last Answer : If the field winding of an unloaded salient pole synchronous motor is open circuited, the motor will stop.

1 answer
518 views

Description : In synchronous motor, does the winding losses vary with load?

Last Answer : No, in the synchronous motor the winding losses do not vary with load.

1 answer
115 views

Description : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Last Answer : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

1 answer
171 views

Description : List different starting methods of three phase synchronous motor. Explain any one of them.

Last Answer : Different Starting Methods of Three Phase Synchronous Motor: As synchronous motor is not self starting, different methods of starting are as follows: 1) By using an Induction (Pony) motor 2) ... . The rotor gets pulled into synchronism and starts running at constant speed as a synchronous motor. 

1 answer
140 views

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Last Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

1 answer
166 views

Last Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

1 answer
169 views

Last Answer : The starting resistance of a D.C. motor is generally low.

1 answer
128 views

Last Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

1 answer
132 views

Description : A synchronous motor can be made self starting by providing?

Last Answer : A synchronous motor can be made self-starting by providing damper bar.

1 answer
166 views

Description : How is a three phase cage induction motor self starting?

Last Answer : Any type of induction motor is self starting. Because the reason for torqe production require two flux displaced by some angle theta.If theta is constant with time then torqe will be constant;if ... torqe also pulsating. In induction motor this angle theta is not pulsating.so it is self starting 

1 answer
116 views

Description : Is induction motor is self starting?

Last Answer : Single phase induction motor is not self starting. Three phase induction motor is self starting.

1 answer
87 views

Description : Why a dc series motor has a high starting torque?

Last Answer : motor

1 answer
114 views

Description : Why starter is required for starting an induction motor?

0 answers
148 views

Description : Why does induction motor have high starting current?

Last Answer : In induction motor , the flux produce is quadrature to the applied voltage. Since when we are going to start motor , there is no flux present inside . So in order to lets say compensate it ... times of current to further increase flux. So that is reason for high starting current in induction motor

2 answers
142 views

Last Answer : Capacitor start motor has high torque in starting

1 answer
94 views

Last Answer : The repulsion-start induction-run motor is used because of high starting torque.

1 answer
165 views

Last Answer : In a two value capacitor motor, the capacitor used for running purposes is paper spaced oil filled type.

1 answer
149 views

Last Answer : The motor used on small lathes is usually single-phase capacitor run motor.

1 answer
110 views

Last Answer : A shaded pole motor can be used for toys, hair dryers, circulators etc.

1 answer
726 views

Last Answer : In a capacitor start and run motors the function of the running capacitor in series with the auxiliary winding is to improve power factor.

1 answer
88 views

Description : State two advantages and disadvantages of centrifugal casting. Write four applications.

Last Answer : Centrifugal Casting: Advantages: 1. Relatively very light impurities move inwards towards center. So they can be removed easily thus helping in producing sound castings. 2. Gates and risers are not needed. ... making rollers. 4. Piston rings. 5. Cylinder liners. 6. Pipes of water gas sewage.

1 answer
217 views

Description : State the insulating materials used in motor. Write temperature class and withstand temperature ranges for them. 

Last Answer : The insulating materials used in motor are as belows: 1. Cotton, 2. Silk, or paper, 3. Press board, 4. Resins 5. PVC 6. Cellulose-Fiber, 7. Enameled coating, etc  ... Over 180° Mica, porcelain, ceramics, glass quartz, asbestos, treated glass fiber or treated asbestos. etc.

1 answer
156 views

Description : State starters used for i) 3-Ph squirrel cage induction motor (3HP) ii) D.C. motor 

Last Answer : Name the starters used for following motors : i) 3 H.P. 3-Ph squirrel cage I.M: i) DOL starter OR ii) Star-Delta Starter OR ii) Auto transformer starter OR iii) Soft start starter.  ii) D.C Shunt Motor : 1) Armature resistance starter (Three Point Starter) OR 2) Four Point Starter 

1 answer
1.1k views

Description : The motor used for electric traction is  (1) D.C. shunt motor (3) D.C. series motor  (2) D.C. compound motor (4) Synchronous motor

Last Answer : The motor used for electric traction is D.C. series motor

1 answer
65 views

Last Answer : The motor used for the compressors is capacitor-start capacitor-run motor.

1 answer
67 views

Last Answer : The shaded pole motor is used for low starting torque.

1 answer
105 views

Last Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

1 answer
57 views

Last Answer : The electric motor used in portable drills is universal motor.

1 answer
77 views

Description : Which type of starter is used to start the DC motor?

0 answers
...