Describe with sketch the method of lubrication of synchromesh gearbox

Describe with sketch the method of lubrication of synchromesh gearbox
by

1 Answer

Answer :

image

Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate lubrication to main shaft gears, Synchronizer , selector fork &,main shaft, lay shaft & clutch shaft Bearings components. The lubricant is thrown against the gravity inside the gearbox casing as droplets or fine mist.


Different lubrication points of synchromesh gear box:

1. The gear box should always remain filled with lubricant. The gears are partially dipped in lubricating oil

2. It lubricates bearing of the gear box

3. Selector mechanism is lubricated by thin machine oil/engine oil

by

Related questions

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Describe with schematic diagram working of constant mesh gearbox

Description : Describe with schematic diagram working of constant mesh gearbox

Last Answer : -In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft. -When the clutch is in engaed position & gears ... than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Describe with neat sketch working of full floating type.

Description : Describe with neat sketch working of full floating type.

Last Answer : Fig:- full floating Rear axle Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. ... supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

Explain construction of Hotchkiss drive with suitable sketch

Description : Explain construction of Hotchkiss drive with suitable sketch

Last Answer : Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft ... torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Compare dry clutch & wet clutch on basis of

Description : Compare dry clutch & wet clutch on basis of

Last Answer : Parameter Dry Clutch Wet Clutch Construction When the clutch is operated dry i.e. without oil, it is called as a dry clutch. When the clutch is operated in an oil bath, it is ... , Bus, Truck etc. Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

Elaborate the working of dry sump lubrication system with sketch.

Description : Elaborate the working of dry sump lubrication system with sketch.

Last Answer : Dry Sump Lubrication: Working of dry sump lubrication system: In this system, the lubricating oil is not stored in oil sump .The oil from the sump is carried to a ... engines. The pressure relief valves are used to maintain the predefined pressure value inside the lubricating system

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box

Compare constant mesh gear box with synchromesh gear box

Description : Compare constant mesh gear box with synchromesh gear box

Last Answer : Sr No. constant mesh gear box  synchromesh gear box  1. It has need of double declutching . No need of double declutching as in case of constant mesh gearbox. 2. Problem in ... noisy as helical gears are used. 4. It has more vibration. It has less vibration.

Should the rev matching feature on the Nissan 370Z's manual gearbox have been put on the automatic instead? Why?

Description : Should the rev matching feature on the Nissan 370Z's manual gearbox have been put on the automatic instead? Why?

Last Answer : What do you mean? Syncro-mesh? That’s not exactly an exotic feature, and why would an automatic need it?

Where is the gearbox inhibtor switch on L200?

Description : Where is the gearbox inhibtor switch on L200?

Last Answer : automatic transmission

The device for engaging and disengaging the power shaft from the gearbox is known as 1. shaft 2. Gear 3. Clutch 4. circuit

Description : The device for engaging and disengaging the power shaft from the gearbox is known as 1. shaft 2. Gear 3. Clutch 4. circuit

Last Answer : ans 3

Hand rotary duster consists basically of a blower completely with ..........and a hopper. a. Clutch. c. Flywheel. d. None of above Ans- b. gearbox

Description : Hand rotary duster consists basically of a blower completely with ..........and a hopper. a. Clutch. c. Flywheel. d. None of above Ans- b. gearbox

Last Answer : Ans-    b. gearbox

List three methods of fuel injection. Describe sequential method with suitable sketch.

Description : List three methods of fuel injection. Describe sequential method with suitable sketch.

Last Answer : Methods of petrol injection 1. Sequential fuel injection. (SFI) 2. Grouped fuel injection. 3. Simultaneous fuel injection 4. Continuous injection.  Sequential Injection: Each injector ... to crank/ camshaft position and pulse width, can be optimized for each individual cylinder.

What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

Description : What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

Last Answer : There are two methods of contouring:- 1. Direct Method 2. Indirect Method - a. By squares  b. By cross section  c. By tacheometric Direct method of contouring - In this ... joining these identical coloured pegs, we get the required contours on ground by this direct method of contouring. 

Describe the method of setting out simple curve by using the method of offset from long chord with sketch.

Description : Describe the method of setting out simple curve by using the method of offset from long chord with sketch. 

Last Answer : Given data: Direction of two straights, chainage of point of intersection, radius of curve. Procedure:  1) Set theodolite over B and measure deflection angle Ф  2) Calculate tangent length by ... equal to tangent length.  4) Divide long chord into even number of equal parts.     

Describe in brief with neat sketch construction of tunnel with needle beam method

Description : Describe in brief with neat sketch construction of tunnel with needle beam method

Last Answer : In this method stout timber beam known as needle beam is used which forms the main temporary support during the excavation. Construction steps: (a) First of all a small drift of about 1 1 m is ... . (d) After excavation, the lining is provided to the tunnel section and mucking is done. 

How promising is the "air lubrication" idea to increase the speed of ships and reduce the consumption of fuel?

Description : How promising is the "air lubrication" idea to increase the speed of ships and reduce the consumption of fuel?

Last Answer : I think passive systems, like shark skin like surfaces, will be more promising than active systems, as those also consume energy. I am also not sure how the bubbles would affect the vessels buoyancy.

What category are ventilation irrigation fertilization and lubrication are called?

Description : What category are ventilation irrigation fertilization and lubrication are called?

Last Answer : Soil

What category are ventilation irrigation fertilization and lubrication?

Description : What category are ventilation irrigation fertilization and lubrication?

Last Answer : Feel Free to Answer

What category are ventilation irrigation fertilization and lubrication are called?

Description : What category are ventilation irrigation fertilization and lubrication are called?

Last Answer : Soil

What product do you use for roller bearing lubrication?

Description : What product do you use for roller bearing lubrication?

Last Answer : Lubrimagic Green is a great product to use for bearing lubrication. You can visit their website at www.synchrony.com/Magnetic_Bearings.

The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Description : The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Last Answer : Answer: D

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Last Answer : Answer: B

During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Description : During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Last Answer : Answer: B

Turbine-Generator Lubrication Oil System Function

Description : Turbine-Generator Lubrication Oil System Function

Last Answer : Turbine-Generator Lubrication Oil System Function For large turbine-generators forced lubrication system and water cooling system should be continuously required during the operation of the turbine-generator and ... when the oil pressure is low. A second backup dc pumps are sometimes provided.

What do you understand by timed cylinder lubrication ?

Description : What do you understand by timed cylinder lubrication ?

Last Answer : For effective lubrication, lub oil needs to be injected between two piston rings when piston is at bottom of stroke so that piston rides in oi during upward movement. This way lot of lub oil can be saved and used properly.

The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Description : The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Last Answer : (d) all of the mentioned

Which bearing is Antifriction bearing A. Thick lubrication bearing B. Thin lubrication bearing C. Rolling or ball bearing D. None

Description : Which bearing is Antifriction bearing A. Thick lubrication bearing B. Thin lubrication bearing C. Rolling or ball bearing D. None

Last Answer : C. Rolling or ball bearing

Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Description : Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Last Answer : D. Antifriction bearing.

Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is generated by the rotation of the journal. [IES-1998] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................Antifriction bearings (c) Somerfield number........................Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Description : Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................ ... .Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Last Answer : (a) Beauchamp tower ........................First experiments on journal bearings