Explain construction of Hotchkiss drive with suitable sketch

Explain construction of Hotchkiss drive with suitable sketch
by

1 Answer

Answer :

image

Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft. Slip joint is used to accommodate change in length of propeller shaft. Leaf spring is shacked at the rear and bracketed at front end. Leaf spring takes Weight of body, driving thrust, side thrust, torque reaction and braking thrust. In the Hotchkiss drive, splines eliminate thrust transmitted back to the driveshaft from the wheels, allowing simple rear-axle positioning using parallel leaf springs. Due to torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

by

Related questions

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Describe with neat sketch working of full floating type.

Description : Describe with neat sketch working of full floating type.

Last Answer : Fig:- full floating Rear axle Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. ... supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

Describe with sketch the method of lubrication of synchromesh gearbox

Description : Describe with sketch the method of lubrication of synchromesh gearbox

Last Answer : Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate ... the gear box 3. Selector mechanism is lubricated by thin machine oil/engine oil

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe with schematic diagram working of constant mesh gearbox

Description : Describe with schematic diagram working of constant mesh gearbox

Last Answer : -In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft. -When the clutch is in engaed position & gears ... than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Compare dry clutch & wet clutch on basis of

Description : Compare dry clutch & wet clutch on basis of

Last Answer : Parameter Dry Clutch Wet Clutch Construction When the clutch is operated dry i.e. without oil, it is called as a dry clutch. When the clutch is operated in an oil bath, it is ... , Bus, Truck etc. Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

Describe construction and working of TBI system with suitable sketch.

Description : Describe construction and working of TBI system with suitable sketch.

Last Answer : Construction and working of TBI system: Throttle Body Injection is an electronically controlled injection system in which an electronic fuel injector injects the fuel intermittently in to the intake manifold ... to calculate the triggering signals for the injectors and other system actuators.

Describe the construction of gear drive of camshaft drive arrangement with sketch.

Description : Describe the construction of gear drive of camshaft drive arrangement with sketch.

Last Answer : Gear Drive of Camshaft Drive: Camshaft is driven by the crankshaft either by a pair of meshing gears (timing gears) or by means of a pair of timing sprocket connected by a chain ... and crankshaft to ensure opening the valves exactly at the correct time in relation to piston position. 

Explain with sketch construction and application of progressive die.

Description : Explain with sketch construction and application of progressive die.

Last Answer : OR Construction A progressive die consists of the following parts.: 1. Stop 2. Sheet metal 3. Pilot 4. Blanking punch 5. Ram 6. Piercing punch 7. Stripper Plate 8. Die ... such as automotive, electronics and appliances. Example car brake caliper, washer, lid of a beverage can etc.

Explain with neat sketch Phreatic line in earthen dam with pressure head at different point and show construction points of this line.

Description : Explain with neat sketch Phreatic line in earthen dam with pressure head at different point and show construction points of this line. 

Last Answer : Procedure for locating the Phreatic line i) Draw an earthen dam having upstream face AB with water surface. ii) On water surface measure distance BC = 0.3 L C is starting pt of base parabola. Let F' ... parabola i.e. Phreatic line. viii) Here G,Q1,Q2,Q3,Q4 and B represent Phreatic line 

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

Explain construction and working of Combination Die with neat sketch.

Description : Explain construction and working of Combination Die with neat sketch.

Last Answer : Combination Die: In this both cutting and non-cutting operations are performed at one station of the press in every stroke of the ram. Figure shows a combination of blanking and drawing die.In this ... as blank holder when the drawing punch descends and draws the blank into the desired shape.

Explain in detail principle, construction and working of Radiation Pyrometer with neat sketch.

Description : Explain in detail principle, construction and working of Radiation Pyrometer with neat sketch.

Last Answer : Radiation pyrometer Principle: According to Stefan Boltzmann's law, the intensity of radiant energy emitted by a hot target varies as the fourth power of its absolute temperature. ... is calibrated in terms of target temperature by using either a voltmeter or Wheatstone bridge circuit.

Explain construction and working of Bimetallic Thermometer with neat sketch.

Description : Explain construction and working of Bimetallic Thermometer with neat sketch.

Last Answer : Bimetallic thermometer: Diagram Construction and working: Bimetallic strip consists of two strips of metal such as invar and brass welded together, each strip made from a metal having a ... The movement of the bimetallic strip is utilized to deflect a pointer over a calibrated scale. 

Explain Construction and working of Francis Turbine with neat sketch.

Description : Explain Construction and working of Francis Turbine with neat sketch.

Last Answer : The main parts of the Francis turbine are: 1) Penstock: It is the large pipe which conveys water from the upstream of the reservoir to the turbine runner. 2) Spiral casing: It is a closed passage ... After doing the work the water is discharge to the trail race through the draft tubes.

Explain the construction and working of induced draft cooling tower with neat sketch.

Description : Explain the construction and working of induced draft cooling tower with neat sketch.

Last Answer : Induced draft cooling tower :  Diagram: Construction and working: Cooling towers are employed to cool utility cooling water by direct contact with air. The parts of a cooling tower are ... top pulls the hot air through the fills and cooled water gets collected in the cold water basin.

With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Description : With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Last Answer : Graphite block heat exchanger:   Graphite heat exchangers are well suited for handling corrosive fluids. Graphite is inert towards most corrosive fluids and has very high thermal conductivity. Graphite being ... vertical faces direct the service fluid through the exchanger in a cross flow.

Explain the construction of ‘Disc Brake’ with neat sketch.

Description : Explain the construction of ‘Disc Brake’ with neat sketch.

Last Answer : Construction of Disc Brake: Modern vehicles always equipped with disc brakes on at least the front two wheels. It consists of mainly 3 parts, [1] Rotor [2] Caliper [3] Brake pads In ... drum. Friction surface directly exposed to air cooling which results better (faster) heat dissipation. 

Explain with neat sketch the construction and working principle of megger.

Description : Explain with neat sketch the construction and working principle of megger.

Last Answer : Megger: Construction of Megger : Two coils: the current coil and pressure coil are mounted at an angle on the same spindle and form the part of the moving system. These coils are ... force produces a torque that is used to deflect the pointer of the device which gives some reading.

Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Description : Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Last Answer : Repulsion Type Moving Iron Instrument: Construction: It consist of fixed cylinder hollow coil which carries operating current inside the coil there are two soft iron pieces. One of which is ... magnetized with same polarity a repulsive force act on them and moving iron piece gets deflected. 

Sketch construction of N-channel JFET and explain its operating principle.

Description : Sketch construction of N-channel JFET and explain its operating principle.

Last Answer : Construction of N-channel JFET: Working of N channel FET: a)when VGS is zero,ID flows because of VDS b)Now when VGS increases towards negative, depletion layer also increases on both sides. c)so VGS control drain current ID d)so it is called as field effect Transistor

Explain the following terms with sketch and suitable range: (i) King pin inclination (ii) Camber

Description : Explain the following terms with sketch and suitable range: (i) King pin inclination (ii) Camber 

Last Answer : (i) King pin inclination It is the angle between vertical line and centre line of king pin or steering axis when viewed from the front of the vehicle. King pin inclination helps the straight ahead ... positive if the tilt is outward at the top. Camber should not generally exceed 2°. 

List eight ways of reducing pollution. Explain PCV and evaporative emission system with suitable sketch.

Description : List eight ways of reducing pollution. Explain PCV and evaporative emission system with suitable sketch.

Last Answer : Eight ways of reducing pollution:-  1) Optimize Ignition Advance 2) Use unleaded gasoline & Low sulphur diesel 3) Use leaner air fuel ratio 4) Use exhaust gas treatment devices ex Catalytic ... check valve. The EVAP system is designed to limit maximum vacuum and pressure in the fuel tank.

Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Description : Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Last Answer : OR 1. The light source is normally an infrared LED or LASER device which is driven by the current value from the V to I convertor. It emits light which is proportional ... optical energy electrical signal. The light detectors which are used as PIN photodiode and avalanche photo diode.

With suitable sketch and explain the working of IMPATT diode.

Description : With suitable sketch and explain the working of IMPATT diode.

Last Answer : Any device which exhibits negative resistance for dc will also exhibit for ac i.e. if an ac voltage is applied current will rise when voltage falls at an ac rate. Hence negative resistance can ... due to applied reverse bias at a drift velocity dependent upon the presence of high dc field.

Recommend & explain with neat sketch a suitable braking mechanism for the large WPP.

Description : Recommend & explain with neat sketch a suitable braking mechanism for the large WPP.

Last Answer : Braking Mechanism For The Large WPP: 1. Furling Mechanism: Furling allows the whole set of blades to change its position and blades turned away from wind, if wind speed is beyond safety limit. It ... 1.To harness optimum power from wind 2.To protect turbine in case of high wind speed.

Write the procedure of construction of WBM road with neat sketch showing various components

Description : Write the procedure of construction of WBM road with neat sketch showing various components

Last Answer : Construction Procedure:  a) Preparation of Foundation: The foundation for receiving the layer of WBM may be either the sub-grade or sub-base or base course. The depressions and pot holes on the existing road ... water and rolled. No traffic is allowed till WBM layer sets and dries out. 

Describe with neat sketch the construction and working of surface condenser

Description : Describe with neat sketch the construction and working of surface condenser

Last Answer : Construction- It consists of horizontal cast iron cylindrical vessel pack with tubes, through which the cooling water flows. The ends of the condenser are cut off by vertical perforated type plates into ... ; the secondary function of condenser is to supply pure and hot feed water to boiler.  

Illustrate with neat sketch the construction of fuel injector

Description : Illustrate with neat sketch the construction of fuel injector

Last Answer : Diesel Fuel Injector: The injector assembly consists of - i) a needle valve ii) a compression spring iii) a nozzle iv) an injector body. When the fuel is supplied to lift the injection pump it ... and hence the valve opening pressure is controlled by adjusting the screw provided at the top.  

Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Description : Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Last Answer : D-LMFI System: It is Manifold fuel injection system.In this type, the vacuum in the intake manifold and volume of air by its density are sensed in this type of MPFI system .As air enters into ... intake manifold , the air flow sensor measures the amount of air and sends information to ECU.

Sketch the construction of tunnel diode and write its operation.

Description : Sketch the construction of tunnel diode and write its operation.

Last Answer : Construction: Applications: • In digital networks. • As a high speed switch. • As a high frequency oscillator. • As a logic memory storage device. • In relaxation oscillator circuits.

Draw the sketch of multiplate clutch and describe its construction and working.

Description : Draw the sketch of multiplate clutch and describe its construction and working. 

Last Answer : Multi - Plate clutch consists of a number of clutch plates instead of only one clutch plate like in the Single plate clutch. Friction surface also increased because of a number of clutch plates. Because of number of friction ... T = n.μ.W.R where R = Mean radius of the friction surfaces

Describe in brief with neat sketch construction of tunnel with needle beam method

Description : Describe in brief with neat sketch construction of tunnel with needle beam method

Last Answer : In this method stout timber beam known as needle beam is used which forms the main temporary support during the excavation. Construction steps: (a) First of all a small drift of about 1 1 m is ... . (d) After excavation, the lining is provided to the tunnel section and mucking is done.