Compare dry clutch & wet clutch on basis of

Compare dry clutch & wet clutch on basis of
by

1 Answer

Answer :

Parameter
Dry Clutch
Wet Clutch
Construction
When the clutch is operated dry i.e. without oil, it is called as a dry clutch.
When the clutch is operated in an oil bath, it is called as wet clutch. In this, clutch plates are always wetted by oil circula
Torque
Torque transmission capacity is higher.
Torque transmission capacity is lower (35-50% of dry clutch), since the clutch plates are wetted by oil
Heat Transmission Or heat dissipation
due to metal and air contact heat dissipation is fair
Due to metal and oil contact heat dissipation is much better.
Application
Single plate dry clutch is used in light motor vehicles for e.g. Jeep, Car, Bus, Truck etc.
Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.
by

Related questions

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

Describe with neat sketch working of full floating type.

Description : Describe with neat sketch working of full floating type.

Last Answer : Fig:- full floating Rear axle Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. ... supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe with schematic diagram working of constant mesh gearbox

Description : Describe with schematic diagram working of constant mesh gearbox

Last Answer : -In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft. -When the clutch is in engaed position & gears ... than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

Describe with sketch the method of lubrication of synchromesh gearbox

Description : Describe with sketch the method of lubrication of synchromesh gearbox

Last Answer : Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate ... the gear box 3. Selector mechanism is lubricated by thin machine oil/engine oil

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Explain construction of Hotchkiss drive with suitable sketch

Description : Explain construction of Hotchkiss drive with suitable sketch

Last Answer : Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft ... torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

State wherein the following clutch is used in Automobiles: 1. Multiplate wet Clutch 2. Diaphragm Clutch 3. Centrifugal Clutch 4. Fluid Coupling

Description : State wherein the following clutch is used in Automobiles: 1. Multiplate wet Clutch 2. Diaphragm Clutch 3. Centrifugal Clutch 4. Fluid Coupling

Last Answer : 1. Multi plate Clutch: i) Multi plate wet clutch used in Two-Wheeler where space is limited. ii) It is also used in racing cars where torque transmission criteria is maximum. iii) ... power, providing variable speed and controlled soft start-up in machine drives, avoiding shock loading. 

If moisture content of solid on dry basis is X, then the same on wet basis is (A) X/(X + 1) (B) X/(1 - X) (C) (1 + X)/X (D) (1 - X)/X

Description : If moisture content of solid on dry basis is X, then the same on wet basis is (A) X/(X + 1) (B) X/(1 - X) (C) (1 + X)/X (D) (1 - X)/X

Last Answer : (A) X/(X + 1)

CO2 measurement of Fyrite kit is based on (EA c) Weight basis (dry) c) Weight basis (wet) d) Volume basis (dry) d) Volume basis (wet)

Description : CO2 measurement of Fyrite kit is based on (EA c) Weight basis (dry) c) Weight basis (wet) d) Volume basis (dry) d) Volume basis (wet)

Last Answer : volume basis

State the location and function of Torsion damper spring and pressure spring in a single plate dry disc clutch.

Description : State the location and function of Torsion damper spring and pressure spring in a single plate dry disc clutch.

Last Answer : Torsion damper spring:  Location: They are small coil springs located between the clutch disc splined hub and the friction disc assembly.  Function: These springs provides a flexible torsional ... locks the engine to the transmission input shaft, causing them to spin at the same speed.

In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Description : In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Dry bulb temperature of unsaturated air is more than its __________ temperature. (A) Dew point (B) Wet bulb (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Dry bulb temperature of unsaturated air is more than its __________ temperature. (A) Dew point (B) Wet bulb (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (C) Both 'a' & 'b

Unsaturated air (with dry and wet bulb temperatures being 35 and 25°C respectively) is passed through water spray chamber maintained at 35°C. The air will be (A) Cooled (B) Humidified (C) Both (A) & (B) (D) Dehumidified

Description : Unsaturated air (with dry and wet bulb temperatures being 35 and 25°C respectively) is passed through water spray chamber maintained at 35°C. The air will be (A) Cooled (B) Humidified (C) Both (A) & (B) (D) Dehumidified

Last Answer : (B) Humidified

Researchers describe seed moisture contents in terms of : a. Dry weight b. Wet weight c. Percent weight d. a & b

Description : Researchers describe seed moisture contents in terms of : a. Dry weight b. Wet weight c. Percent weight d. a & b

Last Answer : a & b

When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the (A) Partial pressure of water vapour is less than the total pressure (B) Humidity is < 100% & dew point temperature of air has not reached (C) Dew point temperature of air has not reached & air is not saturated fully (D) Air is fully saturated

Description : When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the (A) Partial pressure of water vapour is less than the total pressure (B) Humidity is < 100% & dew ... Dew point temperature of air has not reached & air is not saturated fully (D) Air is fully saturated

Last Answer : (D) Air is fully saturated

During sensible heating of humid air (A) Relative humidity increases (B) Dew point remains constant (C) Dry bulb & wet bulb temperature increases (D) Both 'b' & 'c'

Description : During sensible heating of humid air (A) Relative humidity increases (B) Dew point remains constant (C) Dry bulb & wet bulb temperature increases (D) Both 'b' & 'c'

Last Answer : (D) Both 'b' & 'c'

Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Description : Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Last Answer : (D) Dew point temperature

The dew point temperature lines on psychrometric charts are straight inclined sloping downwards to the right. When relative humidity of moist air is 100%, then (A) Wet bulb temperature=dry bulb temperature (B) Wet bulb temperature=dew point temperature (C) Saturation temperature=dew point temperature (D) All 'a', 'b' & 'c

Description : The dew point temperature lines on psychrometric charts are straight inclined sloping downwards to the right. When relative humidity of moist air is 100%, then (A) Wet bulb temperature=dry bulb temperature (B) ... temperature (C) Saturation temperature=dew point temperature (D) All 'a', 'b' & 'c

Last Answer : Option D

Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Description : Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Last Answer : a) Dry Bulb Temperature and Wet bulb Temperature Dry bulb Temperature is an indication of the sensible heat content of air-water vapour  mixtures Wet bulb Temperature is a measure of ... of capital cost. This is a broad indicator of the annual return expected from initial capital investment

A sling psychrometer is used to measure : a) only dry bulb temperature b) only wet bulb temperature c) both a & b d) relative humidity

Description : A sling psychrometer is used to measure : a) only dry bulb temperature b) only wet bulb temperature c) both a & b d) relative humidity

Last Answer : c) both a & b

What is Psychrometer ? Explain dry bulb thermometer & wet bulb thermometer.

Description : What is Psychrometer ? Explain dry bulb thermometer & wet bulb thermometer.

Last Answer : Psychrometers are instruments used for measuring relative humidity. Explanation:- A psychrometer, or wet-and-dry-bulb thermometer, consists of two thermometers, one that is dry and one ... thermometer and the difference in temperatures as shown by the wet-bulb and dry-bulb thermometers.

Compare water and oil of specific gravity 0.8 on the basis of density & viscosity.

Description : Compare water and oil of specific gravity 0.8 on the basis of density & viscosity.

Last Answer : Here it is not possible to find out viscosity

Orsat apparatus(A) Gives flue gas analysis on dry basis (B) Determines N2 in flue gas indirectly (C) Can’t determine CO in flue gas, if it is < 0.2% (D) All (A), (B) & (C)

Description : Orsat apparatus (A) Gives flue gas analysis on dry basis (B) Determines N2 in flue gas indirectly (C) Can’t determine CO in flue gas, if it is < 0.2% (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Why do truck drivers have to "double clutch?"?

Description : Why do truck drivers have to "double clutch?"?

Last Answer : My aunt and uncle truck, so I know I knew this; but couldn't quite remember the reason just now, so I there's a link. Of course, I remember now, but the link's easier. (I also knew just how ... , that many of them are low gears that are normally able to be skipped over, and are there for pinches.)

What is your clutch "feel good" article of clothing (details within)?

Description : What is your clutch "feel good" article of clothing (details within)?

Last Answer : I used to wear bland clothes like plain white T-shirts and I always wore polo shirts, but then I switched up my whole wardrobe and added some more stylish clothes that fit my slim body type and make ... peacoat that makes me look all sophisticated lol. No one on the corner has swagga like us. .

Can you confirm my clutch problem?

Description : Can you confirm my clutch problem?

Last Answer : Did you try hitting it with a hammer?

In a stick shift car, is it easier on the clutch to pop it and get some jerkiness, or to ride it a bit for a smoother transition?

Description : In a stick shift car, is it easier on the clutch to pop it and get some jerkiness, or to ride it a bit for a smoother transition?

Last Answer : answer:The clutch is designed to slip, but it's also designed to wear slightly over time. If you ride it too much you can conceivably wear it out in a couple of hours. If you decide to ... get familiar with the car faster and really lessen the chances of causing damage. Good luck with the dispute.

How difficult is replacing a clutch?

Description : How difficult is replacing a clutch?

Last Answer : depends on if you've done this before. i'd venture to say you haven't since you're asking how hard it would be. I've replaced a clutch as well as rebuilt an engine before and it wasn't too bad.. ... who knows exactly what to do. if so, then see if they could help you or guide you along the process.

I reach for the sky, but clutch to the ground; sometimes I leave, but I am always around.What am I? -Riddles

Description : I reach for the sky, but clutch to the ground; sometimes I leave, but I am always around.What am I? -Riddles

Last Answer : I am Tree.

What is a clutch ?

Description : What is a clutch ?

Last Answer : : The mechanical part used to arbitrarily connect and disconnect one driven shaft with another driven shaft is called a clutch .

When to press the clutch ?

Last Answer : a. When changing gears. B. If the car wants to stop or has to stop while braking.

Does the car have a clutch with automatic?

Description : How many pedals does a car with automatic shifting have?

Last Answer : 2 pedals, clutch pedal not.