Describe with neat sketch working of full floating type.

Describe with neat sketch working of full floating type.
by

1 Answer

Answer :

image

Fig:- full floating Rear axle


Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. The axle end is fitted with the wheel by means of a flange, bolt and nut. There are two roller bearings between the wheel and axle casings. This is the advantage of the fully floating axle, over other two types of axles. To remove the axle the bolt and nut are first loosened. The flange and axle can then be very easily removed. The vehicle continues to be supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

by

Related questions

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Describe with sketch the method of lubrication of synchromesh gearbox

Description : Describe with sketch the method of lubrication of synchromesh gearbox

Last Answer : Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate ... the gear box 3. Selector mechanism is lubricated by thin machine oil/engine oil

Describe with schematic diagram working of constant mesh gearbox

Description : Describe with schematic diagram working of constant mesh gearbox

Last Answer : -In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft. -When the clutch is in engaed position & gears ... than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

Explain construction of Hotchkiss drive with suitable sketch

Description : Explain construction of Hotchkiss drive with suitable sketch

Last Answer : Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft ... torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Compare dry clutch & wet clutch on basis of

Description : Compare dry clutch & wet clutch on basis of

Last Answer : Parameter Dry Clutch Wet Clutch Construction When the clutch is operated dry i.e. without oil, it is called as a dry clutch. When the clutch is operated in an oil bath, it is ... , Bus, Truck etc. Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

Describe working of constant mesh gear box with neat sketch.

Description : Describe working of constant mesh gear box with neat sketch.

Last Answer : Working of constant mesh gear box: A simplified diagram of constant mesh box has been shown in Figure. In this gear box, all gears on the main transmission shaft are constantly connected to corresponding ... In this way by sliding the second dog clutch, second and first gears are obtained.

Describe with neat sketch the working of “Air Suspension”

Description : Describe with neat sketch the working of “Air Suspension”

Last Answer : Working: An air compressor takes the atmospheric air through a filter and compresses it to a pressure of about 240 MPa, at which pressure the air in the accumulator tank is maintained, which ... air gets further compressed and absorbs the shock when the wheel encounters a bump on the road. 

Describe working of Stabilizer bar with neat sketch

Description : Describe working of Stabilizer bar with neat sketch 

Last Answer : Stabilizer (Anti Roll) Bar: Working: When the wheel strikes a bump, it starts vibrating up & down, thus exerting torque on the bar, which acts as a spring. When one road wheel is ... obviate this tendency, a stabilizer is used in car suspension system. It prevents lateral swaying.  

Describe with neat sketch working of air compressor used in automobile workshops. State its two advantages

Description : Describe with neat sketch working of air compressor used in automobile workshops. State its two advantages

Last Answer : As shown in ig. Shows two stages reciprocating air compressor with water cooled and intercooler First of all fresh air is sucked from atmosphere in low pressure (L.P) cylinder during its suction ... :  1) Less power is required to drive the compressor.  2) Higher volumetric efficiency 

Describe with neat sketch the construction and working of surface condenser

Description : Describe with neat sketch the construction and working of surface condenser

Last Answer : Construction- It consists of horizontal cast iron cylindrical vessel pack with tubes, through which the cooling water flows. The ends of the condenser are cut off by vertical perforated type plates into ... ; the secondary function of condenser is to supply pure and hot feed water to boiler.  

Describe with neat sketch of working of bomb calorimeter

Description : Describe with neat sketch of working of bomb calorimeter

Last Answer : working of bomb calorimeter:   The calorimeter is made of austenitic steel which provides considerable resistant to corrosion and enables it to withstand high pressure. In the calorimeter use of a strong ... the calorimeter. From the above data the calorific value of the fuel can be found.  

Describe the working of water/liquid cooling system with neat sketch.

Description : Describe the working of water/liquid cooling system with neat sketch.

Last Answer : A water-cooled engine block and cylinder head have interconnected coolant channels running through them. At the top of the cylinder head all the channels converge to a single outlet. A pump, driven by a ... speed increases. There is no necessity of maintaining the water up to a correct level.  

Describe the working of four stroke C. I. engine with neat sketch.

Description : Describe the working of four stroke C. I. engine with neat sketch. 

Last Answer : Working principle of CI engine: 1. Suction stroke: During this stroke, inlet valve is open and exhaust valve is closed. Only air is sucked into cylinder during this stroke. The ... burnt gases outside the combustion chamber. Crankshaft rotates by two complete revolutions through 720˚. 

Describe the working of EGR valve with neat sketch.

Description : Describe the working of EGR valve with neat sketch.

Last Answer : Answer: Exhaust Gas Recirculation Valve (Operation-2 marks, Sketch-2 marks) When the engine is idling, the EGR valve is closed and there is no EGR flow into the manifold. The EGR valve remains closed ... exhaust gas (less than 10% of total) to be supplied into the incoming air: fuel mixture

Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Description : Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Last Answer : D-LMFI System: It is Manifold fuel injection system.In this type, the vacuum in the intake manifold and volume of air by its density are sensed in this type of MPFI system .As air enters into ... intake manifold , the air flow sensor measures the amount of air and sends information to ECU.

Describe the working of fuel injector with neat sketch

Description : Describe the working of fuel injector with neat sketch

Last Answer : Fuel Injector: The injector assembly consists of - i) a needle valve ii) a compression spring iii) a nozzle iv) an injector body When the fuel is supplied to lift the injection ... spring tension and hence the valve opening pressure is controlled by adjusting the screw provided at the top.

Describe the working of PN junction diode with neat sketch under forward biased condition.

Description : Describe the working of PN junction diode with neat sketch under forward biased condition.

Last Answer : If the p-region (anode) is connected to the positive terminal of the external DC source and nside (cathode) is connected to the negative terminal of the DC source then the biasing ... The large number of majority carriers crossing the junction constitutes a current called as the forward current.

Describe working of variable air gang capacitor with neat sketch.

Description : Describe working of variable air gang capacitor with neat sketch.

Last Answer : ( OR)   working: Consider the structure of the above figure. It mainly consists of two sets of aluminium plates separated from each other by air. These metal plates may be rotary or ... when the shaft is rotated. Sometimes, two or more such capacitors are operated by a single shaft.  

Describe working of screw conveyor with neat sketch.

Description : Describe working of screw conveyor with neat sketch.

Last Answer : 1. A Screw conveyor consist of a continuous or broken blade helix or screw fastened to the shaft (or a pipe) 2. This helix or screw rotates in trough so that revolving screw advances the material. 3. ... divided solids or pasty solids. 4. This conveyor can also be used as mixture or blender. 

Describe with neat sketch working of natural draft cooling towers.

Description : Describe with neat sketch working of natural draft cooling towers.

Last Answer : Natural draft cooling tower: -In natural draught cooling tower, the circulation of air is produced by the pressure difference of air inside the tower and outside atmospheric air Hot cooling water falls down ... the pressure difference of air inside and outside of cooling tower (natural flow).

With neat sketch describe working of reaction turbine.

Description : With neat sketch describe working of reaction turbine.

Last Answer : Working principle of reaction turbine- -A turbine in which steam pressure decreases gradually while expanding through the moving as well as through the fixed blade is known as reaction turbine. -In pure ... the steam to leave the moving blade as higher velocity than as which it entered.

Describe working of variator drive with neat sketch.

Description : Describe working of variator drive with neat sketch.

Last Answer : Working of Variator Drive: Vario-drive provides various drive ratios between the engine and rear wheel according to the engine speed and load. It consists of two set of split pulleys - drive and ... this occurs, the drive ratio decreases and less torque is delivered to the final reduction.

Describe working of centrifugal clutch with neat sketch.

Description : Describe working of centrifugal clutch with neat sketch.

Last Answer : Centrifugal clutch-  Working of Centrifugal Clutch: Centrifugal clutch works on the principle of centrifugal force. When the engine is started, the speed of the driving shaft is less, so the centrifugal force ... disengaged at low speed. The stop H limits the amount of centrifugal force.

Describe in brief working of Symons rain gauge with neat labelled sketch.

Description : Describe in brief working of Symons rain gauge with neat labelled sketch.

Last Answer : The most common type of non- recording rain gauges used in our country is the Symon's raingauge'.  Working: A Symons Rain gauge consists of a cylindrical vessel of 127 mm internal diameter with an enlarged ... rim which is then measured by the measuring glass in mm' and tenth of mm'

Describe the working of pick-up assembly of CD player with the help of neat sketch.

Description : Describe the working of pick-up assembly of CD player with the help of neat sketch.

Last Answer : Diagram: Explanation: The pick-up assemble consist of - * A low power laser diode to illuminate the CD tracks. * Lens and prism arrangement to direct the laser beam to the ... beam is applied to a group of photodiodes through objectives lens, collamination lens and some prism arrangement. 

Describe with neat sketch working of hysteresis motor.

Description : Describe with neat sketch working of hysteresis motor.

Last Answer : Working: When stator is energized with single phase ac supply, rotating magnetic field is produced because of starting (auxiliary) and main windings, which remain in circuit permanently. The ... the principle of magnetic locking this motor either rotates at synchronous speed or not at all.

Describe with neat sketch the construction and working principle of MOSFET.

Description : Describe with neat sketch the construction and working principle of MOSFET.

Last Answer : Construction and working principle of MOSFET:  A) Depletion type MOSFET: Construction: The N-channel depletion type MOSFET is formed on P-type silicon substrate with two heavily ... accumulation of electrons and hence more current. Thus the MOSFET is a gate voltage controlled device.

Describe the working of capacitor with a neat sketch.

Description : Describe the working of capacitor with a neat sketch.

Last Answer : Working of Capacitor: When we connect a battery (DC Voltage Source) across the capacitor, one plate (plate-I) gets attached to the positive terminal and another plate (plate-II) to the negative ... charges for a certain time. Thus the charged capacitor acts as a source electrical energy. 

Describe working of venturimeter with neat sketch.

Description : Describe working of venturimeter with neat sketch.

Last Answer : Explanation- It is a primary element of differential pressure Flow meters. 1) It consists of a straight inlet section, a converging conical inlet section, a cylindrical throat and diverging recovery cone. ... the buildup of heavy materials. d) Rectangular from which is used in air-duct work. 

Explain with neat sketch, the working of full wave rectifier voltmeter.

Description : Explain with neat sketch, the working of full wave rectifier voltmeter.

Last Answer : Full Wave Rectifier Type Voltmeter: Working of full wave rectifier type A. C. Voltmeter Referring to the circuit diagram, for rectification, a full wave bridge circuit (ABCD) is used. Input ... current passing through meter is given as, which causes full scale deflection of the meter.

(i) Illustrate with neat sketch the working of absorber type of muffler (ii) sketch bellow type of thermostat

Description : (i) Illustrate with neat sketch the working of absorber type of muffler (ii) sketch bellow type of thermostat

Last Answer : (i) Working of absorber type of muffler: It consists of a perforated tube, around which a sound absorbing material, like fiber glass or steel wool is placed. The exhaust gases pass through the perforated tube. ... thus reducing the noise intensity.  (ii) Bellow type of thermostat:

Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Description : Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Last Answer : Repulsion Type Moving Iron Instrument: Construction: It consist of fixed cylinder hollow coil which carries operating current inside the coil there are two soft iron pieces. One of which is ... magnetized with same polarity a repulsive force act on them and moving iron piece gets deflected.