Describe with schematic diagram working of constant mesh gearbox

Describe with schematic diagram working of constant mesh gearbox
by

1 Answer

Answer :

image

-In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft.

-When the clutch is in engaed position & gears are netral position & engine is running an additional part called “Dog clutch”is provide between mainshaft gears slide on splined shftb with help of selector mechanism.

-a whole assembly enclosed in the gearbox hausing and filled with specific grade oil in specific quantity


Working:-

Neutral Gear:-in neutral stage all dog clutches remains at centre position and no power transmit throgh gearbox.


1 st Gear:-As the right side dog clutch slide towards left and its teeth mesh with teeth of first gear on mainshft than first gear ratio obtained which is near about 3:1


2 nd Gear:- When left side dog clutch slide towards right side and its teeth mesh with teeth of second gear on mainshft than second gear ratio obtained which is near about 2.5:1


3 rd Gear or Top gear:- :- When left side dog clutch slide towards left side and its teeth mesh with teeth of clutch shaft gear than third gear ratio obtained which is near about 1:1


Reverse Gear:- As the right side dog clutch slide towards right side and its teeth mesh with teeth of reverse gear on mainshft than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

by

Related questions

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Describe with sketch the method of lubrication of synchromesh gearbox

Description : Describe with sketch the method of lubrication of synchromesh gearbox

Last Answer : Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate ... the gear box 3. Selector mechanism is lubricated by thin machine oil/engine oil

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

Describe with neat sketch working of full floating type.

Description : Describe with neat sketch working of full floating type.

Last Answer : Fig:- full floating Rear axle Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. ... supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Compare dry clutch & wet clutch on basis of

Description : Compare dry clutch & wet clutch on basis of

Last Answer : Parameter Dry Clutch Wet Clutch Construction When the clutch is operated dry i.e. without oil, it is called as a dry clutch. When the clutch is operated in an oil bath, it is ... , Bus, Truck etc. Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

Explain construction of Hotchkiss drive with suitable sketch

Description : Explain construction of Hotchkiss drive with suitable sketch

Last Answer : Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft ... torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

Describe the working of pressure regulation in PFI system with the help of schematic diagram.

Description : Describe the working of pressure regulation in PFI system with the help of schematic diagram.

Last Answer : Working of Pressure Regulator in PFI System: The fuel pump provides more fuel than the maximum required by the engine. Fuel not used by the engine is returned to the fuel tank. The fuel rail supplies all injectors. ... between 2.0 and 3.5 bar and allows excess fuel to return to the fuel tank.

Describe working of constant mesh gear box with neat sketch.

Description : Describe working of constant mesh gear box with neat sketch.

Last Answer : Working of constant mesh gear box: A simplified diagram of constant mesh box has been shown in Figure. In this gear box, all gears on the main transmission shaft are constantly connected to corresponding ... In this way by sliding the second dog clutch, second and first gears are obtained.

Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

Description : Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

Last Answer : Constructional features of welding transformer: Working of welding transformer: i) It is a step down transformer that reduces the voltage from the source voltage to a voltage desired according to the demands of ... 230 V, 415 V Secondary voltage - 40 to 60 V Secondary current - 200 to 600 A

Describe re-entrant procedure with the help of schematic diagram.

Description : Describe re-entrant procedure with the help of schematic diagram.

Last Answer : Re-entrant Procedures: A procedure is said to be re-entrant, if it can be interrupted, used and re-entered without losing or writing over anything. To be a re-entrant, Procedure ... program execution flow reenters in the procedure1. These types of procedures are called reentrant procedures.

What is the purpose of the schematic diagram?

Description : What is the purpose of the schematic diagram?

Last Answer : The schematic diagram is a Road Map of the electrical circuitsof a device. It is the most important and most helful piece ofinformation available to help track down a problem in that device.You need plans to erect a building so do you need a schematicdiagram to build a electronic circuit

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

If fuse 'F-1' in the illustrated schematic diagram opens, ____________. EL-0017 A. the motor will run slowly B. 'A-1' and 'A-2' will open C. the motor will not start D. the start button will jam in the closed position

Description : If fuse 'F-1' in the illustrated schematic diagram opens, ____________. EL-0017 A. the motor will run slowly B. 'A-1' and 'A-2' will open C. the motor will not start D. the start button will jam in the closed position

Last Answer : Answer: C

The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Last Answer : Answer: D

In the illustrated schematic diagram, which of the listed devices prevents the forward and reversing coils from being energized simultaneously? EL-0011 A. An 'either-or' interlock B. A mechanical interlock C. Blowout coils D. A stop button

Description : In the illustrated schematic diagram, which of the listed devices prevents the forward and reversing coils from being energized simultaneously? EL-0011 A. An 'either-or' interlock B. A mechanical interlock C. Blowout coils D. A stop button

Last Answer : Answer: A

If the three-phase motor, shown in the illustrated schematic diagram, is running in the forward direction, which of the following actions must occur before the motor will reverse rotation? EL-0011 A. Normally-closed contacts '4'-'5' must open. B. Normally- open contacts '2'-'3' must close. C. 'L1' and 'L3' must be interchanged via the 'R' contacts. D. All of the above.

Description : If the three-phase motor, shown in the illustrated schematic diagram, is running in the forward direction, which of the following actions must occur before the motor will reverse rotation? EL-0011 A. Normally-closed ... 'L1' and 'L3' must be interchanged via the 'R' contacts. D. All of the above.

Last Answer : Answer: C

Refering to the illustrated schematic diagram, which of the following statements is true when the motor is running in the forward direction? EL-0011 A. Normally-open contacts '4-5' are closed. B. Current flows through the 'Reverse' push-button switch. C. Normally-closed contacts 'R' are open. D. The blowout coils must be closed.

Description : Refering to the illustrated schematic diagram, which of the following statements is true when the motor is running in the forward direction? EL-0011 A. Normally-open contacts '4-5' are closed. B. Current ... switch. C. Normally-closed contacts 'R' are open. D. The blowout coils must be closed.

Last Answer : Answer: B

Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Description : Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Last Answer : Answer: A

The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Description : The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Last Answer : Answer: C

The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Last Answer : Answer: A

Which of the illustrations listed below is representative of a motor controller's 'schematic' or 'elementary' diagram? A. EL-0023 B. EL-0007 C. EL-0037 D. EL-0058

Description : Which of the illustrations listed below is representative of a motor controller's 'schematic' or 'elementary' diagram? A. EL-0023 B. EL-0007 C. EL-0037 D. EL-0058

Last Answer : Answer: B

Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Description : Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Last Answer : To find the test points.

Explain concept of capacitive type proximity switch with neat schematic diagram.

Description : Explain concept of capacitive type proximity switch with neat schematic diagram.

Last Answer : Capacitive type proximity switch: A capacitive proximity switch is device that senses presence of metallic or nonmetallic objects. The internal circuit consists of an oscillator, threshold detection stage and ... in oscillation amplitude is detected and output switching device is turned on. 

Explain with schematic diagram direct distribution of solar energy.

Description : Explain with schematic diagram direct distribution of solar energy.

Last Answer : Explain with schematic diagram direct distribution of solar energy: Solar energy reaching earth's surface consists of two components: i) Direct solar energy, ii) Diffused solar energy. Direct solar energy ... radiation. It is very intense radiation and it can produce sun burns and shadows.

Should the rev matching feature on the Nissan 370Z's manual gearbox have been put on the automatic instead? Why?

Description : Should the rev matching feature on the Nissan 370Z's manual gearbox have been put on the automatic instead? Why?

Last Answer : What do you mean? Syncro-mesh? That’s not exactly an exotic feature, and why would an automatic need it?

Where is the gearbox inhibtor switch on L200?

Description : Where is the gearbox inhibtor switch on L200?

Last Answer : automatic transmission

The device for engaging and disengaging the power shaft from the gearbox is known as 1. shaft 2. Gear 3. Clutch 4. circuit

Description : The device for engaging and disengaging the power shaft from the gearbox is known as 1. shaft 2. Gear 3. Clutch 4. circuit

Last Answer : ans 3

Hand rotary duster consists basically of a blower completely with ..........and a hopper. a. Clutch. c. Flywheel. d. None of above Ans- b. gearbox

Description : Hand rotary duster consists basically of a blower completely with ..........and a hopper. a. Clutch. c. Flywheel. d. None of above Ans- b. gearbox

Last Answer : Ans-    b. gearbox

In a hundred-line exchange 24 two-motion selectors are used. Draw the schematic you suggest for this exchange and explain its working. How many simultaneous calls can be made during peak hour in this exchange?

Description : In a hundred-line exchange 24 two-motion selectors are used. Draw the schematic you suggest for this exchange and explain its working. How many simultaneous calls can be made during peak hour in this exchange?

Last Answer : The desired schematic for 100 lines exchange with 24 two motion selectors is shown in Fig.   In the case, 24 simultaneous calls can be put through the switch . Typically, a 24- ... selector. At the next step, the two-motion selector responds to the dial pulses for appropriate connection.

Using a combination of uniselectors and two motion selectors, draw a schematic of thousand line exchange and explain its working.

Description : Using a combination of uniselectors and two motion selectors, draw a schematic of thousand line exchange and explain its working.

Last Answer : The schematic diagram for such an exchange is given in Fig. Each subscriber is connected to a single rotary pre-selector switch at the exchange, the outputs from  this switch being ... further digits, connection is established, providing the called subscriber's to answer his telephone.  

Explain the working of Hydro power station with schematic layout.

Description : Explain the working of Hydro power station with schematic layout. 

Last Answer : Working of Hydro- Electric Power Plant: Water stored at high level by constructing dam across river. This stored water has potential energy. This stored water is passed to run the water ... energy and Alternator is coupled to water turbine which converts mechanical energy into electrical energy. 

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box