What is Propagation Delay ?

What is Propagation Delay ?
by

1 Answer

Answer :

The time required for the flow of signals in a logic gate or circuit is called Propagation delay .
by

Related questions

________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Description : ________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Last Answer : c. Modal dispersion

What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Description : What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Last Answer : A. 256 msec

The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Last Answer : A. 500 to 600 ms

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

The maximum propagation delay of a geostationary satellite is A. 278 ms B. 239 ms C. 300 ms D. 250 ms

Description : The maximum propagation delay of a geostationary satellite is A. 278 ms B. 239 ms C. 300 ms D. 250 ms

Last Answer : A. 278 ms

What is the minimum propagation delay of a geostationary satellite? A. 278 ms B. 239 ms C. 300 ms D. 600 ms

Description : What is the minimum propagation delay of a geostationary satellite? A. 278 ms B. 239 ms C. 300 ms D. 600 ms

Last Answer : B. 239 ms

What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Description : What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Last Answer : C. Propagation delay

The phase constant of a wave propagation with frequency of 35 radian/sec and time delay of 7.5 sec is a) 4.66 b) 262.5 c) 46.6 d) 26.25

Description : The phase constant of a wave propagation with frequency of 35 radian/sec and time delay of 7.5 sec is a) 4.66 b) 262.5 c) 46.6 d) 26.25

Last Answer : b) 262.5

Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Description : Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Last Answer : d. 256

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocolc. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Description : Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocol c. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Last Answer : CSMA/CD is not suitable for a high propagation delay

Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Description : Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Last Answer : c. 464

The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channelcapacity. Assuming that processing delay is negligible, the minimum number of bits for the sequence number field in a frame for maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Last Answer : c. C

In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Description : In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Last Answer : c. 20 metres of cable.

Define propagation delay.

Description : Define propagation delay.

Last Answer : A propagation delay is the time required to change the output after the application of the input.

What is propagation delay?

Description : What is propagation delay?

Last Answer : Propagation delay is the average transition delay time for the signal to propagate from input to output when the signals change in value. It is expressed in ns.

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Description : A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Last Answer : Ans: A 15 ns because in synchronous counter all the flip-flops change state at the same time.

In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Description : In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Last Answer : Ans: A Lower propagation delay as shottky transistors reduce the storage time delay by preventing the transistor from going deep into saturation.

The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Description : The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Last Answer : Ans: A The digital logic family which has the lowest propagation delay time is ECL (Lowest propagation delay time is possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated).

Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Description : Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Last Answer : i) Noise immunity is measured in terms of noise margin. High state Noise margin = VNH = VOH(min) - VIH(min) Low state Noise margin = VNL = VIL(max) - VOL(max) i) The fan-out is defined as the ... logical 0 state (HIGH to LOW) iii) Average power dissipation is defined as PD(avg) = ICC(avg) * VCC

The following logic families have their propagation delay. Arrange them from lowest propagation delay to

Description : The following logic families have their propagation delay. Arrange them from lowest propagation delay to highest propagation delay. 1. TTL (Standard) 2. ECL 3. Low power CMOS 4. DTL (A) 2, 1, 4 and 3 (B) 2, 4, 1 and 3 (C) 4, 2, 3 and 1 (D) 1, 2, 3 and 4

Last Answer : The following logic families have their propagation delay. Arrange them from lowest propagation delay to highest propagation delay. 1. TTL (Standard) 2. ECL 3. Low power CMOS 4. DTL (A) 2, 1, 4 and 3 (B) 2, 4, 1 and 3 (C) 4, 2, 3 and 1 (D) 1, 2, 3 and 4

The propagation delay in a CMOS inverter is

Description : The propagation delay in a CMOS inverter is  (A) proportional to (W/L) ratio  (B) inversely proportional to (W/L) ratio  (C) independent of (W/L) ratio  (D) depends only on W

Last Answer : The propagation delay in a CMOS inverter is inversely proportional to (W/L) ratio 

A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10

Description : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is

Last Answer : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is 12.67 MHz

What is the propagation delay of a logic gate?

Description : What is the propagation delay of a logic gate?

Last Answer : The application input pulse and the occurrence of resulting output pulse is called propagation delay of logic gate.

What is the conductivity of molar ?

Description : What is the conductivity of molar ?

Last Answer : The density of a solution as cm. When one mole of electrolytic substance is dissolved in it, the conductivity obtained by multiplying it by the relative conductivity of the solution is called molecular conductivity of the solution .

How do I purchase a product ?

Description : How do I purchase a product ?

Last Answer : From Alibaba you can purchase products by paying MASTER CARD or through bank.

What is an analog signal ?

Description : What is an analog signal ?

Last Answer : Signals whose values ​​change continuously are called analog signals. For example- voltage of electricity supplied to the house.

What is Zener Diod ?

Description : What is Zener Diod ?

Last Answer : Zener diode is a special type of diode which, like ordinary diode, not only conducts current in the forward direction , but also in the opposite direction if the voltage exceeds the level of breakdown ... diode is to use the shunt regulator and the voltage reference as the voltage of the circuit.

What is the multiplying factor of shunt ?

Description : What is the multiplying factor of shunt ?

Last Answer : Answer : The ratio of load or matte current to ammeter current is called shunt multiplying power.

What is ammeter shunt ?

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

What is short circuit current ?

Description : What is short circuit current ?

Last Answer : Answer : A fault in an electrical system whose current, before or after the current flows through the load, is combined with one or more phases of neutral current which causes more current to flow than normal. The current is called short circuit current.

What is a current limiting reactor ? How many types and what are they ?

Description : What is a current limiting reactor ? How many types and what are they ?

Last Answer : Answer : A current limiting reactor is basically an inductive coil which limits the short circuit current by providing inductive reactance when required. Types: 1. Based on the structure- a) Dry type ... reactor. Basbar reactors are again of 2 types- a) Ring system reactor b) Tiber system reactor

What is the method of diagnosing short circuit current ?

Description : What is the method of diagnosing short circuit current ?

Last Answer : There are three methods for determining short circuit current , namely- 1) Ohmic method 2) Per unit method 3.) Percentage reactance method.

What are symmetrical and asymmetrical faults ?

Description : What are symmetrical and asymmetrical faults ?

Last Answer : Symmetrical Fault: The same amount in each phase due to the float in the electrical system. The fault that causes hot current to flow is called semantic fault. Circuit breaker ratings are determined by ... through each fan is called an asymmetrical fault. The relay is set via asymmetrical font.

What is Basbar and Bas Kaplar ?

Description : What is Basbar and Bas Kaplar ?

Last Answer : Basbar : Basbar is basically a sheet or color of copper or aluminum. It is the job of the bus driver to deliver power to one or more lads with power from one or more cables. Bus ... is basically a combination of circuit breaker and isolator. There are fire proof walls around the bus coupler.

Why is the busbar sectionalized ?

Description : Why is the busbar sectionalized ?

Last Answer : Answer : If an error occurs in any part of the busbar, the operation of the entire busbar system will not stop. The maximum success of this system is due to the interconnection of different sections of the circuit and the smooth distribution in the outgoing circuit.

title : _

Description : title : _

Last Answer : Basbar is a type of copper and aluminum conductive sheet or mata rod , which collects electrical energy from one or more circuits and distributes that energy through one or more circuits.

Write different font names or different short circuit font names ?

Description : Write different font names or different short circuit font names ?

Last Answer : There are two main types of short circuit faults. Namely- 1. Semantic faults and 2. Asymmetrical font Symmetrical fault - a) Short circuit three phases together b) Short circuit asymmetrical fault with three ... result c) Double line to ground font d) Two phase one Circuit and third phase earth.

What is Electrical Fault ? What is the cause of the fault ?

Description : What is Electrical Fault ? What is the cause of the fault ?

Last Answer : Answer : Fault: When two or more conductors come in contact with each other while operating at normal voltage difference, the result is said to be organized. Causes of Fault: Faults are organized due to ... loss of line c) Lightning charge d) Voltage drop e) Loss of unbalance and stability etc.

What features should a switchgear have ?

Description : What features should a switchgear have ?

Last Answer : Switchgear should have the following characteristics- a) Sensitivity b) Detection ability c) Reliability d) High speed e) Durability. F) Expansion advantage g) Simplicity.

What are the components of switch gear ?

Description : What are the components of switch gear ?

Last Answer : The components of switch gear are: circuit breaker , relay , instrument transformer , housing , conductor etc.

What do you mean by switchgear ?

Description : What do you mean by switchgear ?

Last Answer : Answer : Switch gear does not mean a single corner object. It refers to the position of the electromagnetic system, including the connective , isolating , and maintenance equipment of normal activity .

What is an Earth Electrode ?

Description : What is an Earth Electrode ?

Last Answer : Puta metal part in the soil which connects to the soil is called earth electrode. Thank you all for today's electrical questions and answers.

What is Earthing Lead ?

Description : What is Earthing Lead ?

Last Answer : The wire that connects the earth continuity wire and the earth electrode is called the earthing lead.

What earthing is done in hilly areas ?

Description : What earthing is done in hilly areas ?

Last Answer : Sheet earthing is done in hilly areas. Shit electrodes are placed by digging trenches on the slopes of the hill.

What should be the size of rod earthing ?

Description : What should be the size of rod earthing ?

Last Answer : In case of iron or steel rod the diameter is 16 mm but in case of copper rod it is 12.5 mm. In both cases the length is at least 2.5 m. Is to be.

What does earth continuity mean ?

Description : What does earth continuity mean ?

Last Answer : The conduction wire that connects the earthing lead to the metal cover of electrical furniture, appliances, or wiring is called the earth continuity wire.

Which earthing is less expensive ?

Description : Which earthing is less expensive ?

Last Answer : Rod earthing is the least expensive. Because the soil does not have to be eroded, the cost is less than other earthing.

What should be the size of the pipe electrode ?

Description : What should be the size of the pipe electrode ?

Last Answer : The size of the pipe electrode should be 36 mm diameter 2 to 2.75 m long galvanized iron or steel pipe.