Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld
Last Answer : a) Never
Description : Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable
Last Answer : a) The welding engineer
Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding
Last Answer : b) Report the incident and record all relevant information
Description : Weather date of welding is marked on weld? (i) Yes (ii) As decided by the site supervisor (iii) No* (iv) None of the above
Last Answer : (iii) No*
Description : Which gauge is used to measure the height of rail at the time of aligning of rails for AT welding? (i) Height gauge.* (ii) Vertical gauge (iii) Horizontal gauge (iv) As decided by site supervisor
Last Answer : (iv) As decided by site supervisor
Description : Weather traffic block is required for execution of AT Welding? (i) Yes.* (ii) No (iii) As decided by site supervisor (iv) As per site condition
Last Answer : (i) Yes.
Description : Weather protection of track is required during block for execution of AT Welding? (i) Yes.* (ii) No (iii) As decided by site supervisor (iv) As per site condition
Last Answer : (i) Yes.*
Description : Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department
Last Answer : a) The welder and the welding inspector
Description : Who should have access to the WPQR’S? a) NDT operators b) Inspectors only c) Welders only d) Welding Engineer
Last Answer : d) Welding Engineer
Description : The Overall in-charge of an organisation at the site responsible for the execution of the works, is (A) Executive Engineer (B) Engineer (C) Junior Engineer (D) Assistant Engineer
Last Answer : (B) Engineer
Description : What is the average salary for an entry level job as a welding engineer?
Last Answer : The average salery for an entry level job as a welding engineeris pretty good you will make $56000 a year which isn't bad its amoderate living to survive.
Description : What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure
Last Answer : c) Welding procedure
Description : Should you always discuss personal safety issues with your supervisor?
Last Answer : Generally, yes. The question isn't precisely worded, and thedevil's advocate in me seeks contradictions to the generallyaccepted answer to this question. If you discuss any safety issuewith your supervisor ... Probably not.Should you ever notice a safety issue and do nothing about it?Probably not.
Description : Can I hire whomever I please as a safety supervisor in the oil and gas industry or are there minimum levels of certifications required to work such a position legally speaking?
Last Answer : I would hope there are qualified people since they are dealing with the lives of workers. I suggest you contact the agency that provides information on what the qualifications are in that business.
Description : Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove ... contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.
Last Answer : Answer: D
Description : Health and Safety Engineer?
Last Answer : For individuals with an interest in science and a desire to help people through the development of safety programs within the workplace, a career as a health and safety engineer may be the perfect ... help reduce or eliminate the risk of injury to people and damage to property.Health and safety eng
Description : On Indian Railways a new level crossing can be provided with the approval of a) Chief engineer b) General Manager c) Commissioner of Railway Safety d) None of the above*
Last Answer : d) None of the above
Description : As the supervisor, you are responsible for transforming your office so that it closely reflects a workplace that values differences in others. How can you support an environment of valuing differences?
Last Answer : All of the Above....Not sure....
Description : What is the work of responsible Supervisor
Last Answer : Responsibilities of responsible supervisor Examine the worksite with permit applicant before authorizing (A) class permit. Decide whether it is necessary to restrict other work at the site while the class ... brief detail of the work which can be seen when permit is placed in a permit rack
Description : The supervisor of a CRC is responsible for a) Timely opening of the set b) Maintaining the master data for the interim dispatch c) Opening bag allocation closing bag allocation d) All the above
Last Answer : d) All the above
Description : Who is the responsible person to collect the amount of unpaid postage from insufficiently paid letters and newspapers? a. Supervisor of Mail Branch b. Supervisor of delivery Branch c. Postmaster
Last Answer : c. Postmaster
Description : What is the most important quality a supervisor should have?
Last Answer : The ability to inspire / lead a team towards one common vision.
Description : __________ involves giving frontline employees the authority and responsibility to make marketing decisions without seeking the approval of a supervisor. A)Benchmarking B)Internal marketing C)Total quality management D)Empowerment
Last Answer : D)Empowerment
Description : What type of safety protection do you need for standard welding equipment?
Last Answer : "While using welding equipment, you should always wear safety googles and protective gloves." Make sure you have on a welding jacket and long pants when you're using welding equipment. Those sparks can be very dangerous.
Description : While Doing Welding What Are The Safety Measures That Worker Should Follow?
Last Answer : While doing welding, workers should follow the rules like: Respirator or welders mask: Use mask or respirators as per your projects, match the filter to the types of metals and coatings used ... be a cover with protective and clothes which can bear heat and spark emitted from the welding.
Description : Thickness of Lining/Charge is kept? (i) 20 mm. (ii) 25 mm* (iii) 30 mm (iv) As decided by the site supervisor
Last Answer : (ii) 25 mm*
Description : How much rail ends are cleaned with Kerosene Oil and steel wire brush? (i) Minimum 100 mm both side (ii) Minimum 50 mm both side.* (iii) No need (iv) As decided by site supervisor
Last Answer : (ii) Minimum 50 mm both side.*
Description : Ideas for something fun to reverse engineer and take apart?
Last Answer : answer:While this might sound boring, ripping apart our front loading washing machine to clean the pump was interesting. It wasn't really hard but it was interesting. I just tried to replace the home ... iPhone 4 and it was a fucking disaster. A washing machine is way easier to get back together.
Description : The first chip ………… was made by Intel in 1971 scientist Ted Hoff and engineer Frederico Faggin -Technology
Last Answer : The first chip Intel 4004was made by Intel in 1971 scientist Ted Hoff and engineer Frederico Faggin
Description : Which of the following approved $201.50 million for Technical Education Quality Improvement Project in India? A) World Bank B) Asian Development Bank C) International Monetary Fund D) European Development Bank E) None of these
Last Answer : A) World Bank Explanation: United States based World Bank‘s Board of Executive Directors has approved $201.50 million for Technical Education Quality Improvement Project III in India
Description : The audit work performed by each assistant should be reviewed to determine whether it was adequately performed and to evaluate whether the a. Results are consistent with the conclusions to be presented in the ... as auditors. d. Auditor's system of quality control has been maintained at a high leve
Last Answer : Results are consistent with the conclusions to be presented in the auditor's report.
Description : What equipment (or programs, plugins, etc.) would I need as an audio engineer to make the quality of my music sound radio-ready?
Last Answer : A lot of the sound has to do with how it’s mastered – you want to compress while not overly affecting dynamic range.
Description : How To Get Interviews For Quality Engineer Jobs ?
Last Answer : Before you can get a job as a quality engineer, you need to do well at an interview. Here are some tips to help you get to the interview stage when you are applying for quality ... each particular company to which you apply. Your resume should also be straightforward and free from any errors.
Description : What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing: a) Cellulosic b) Rutile c) Fused d) Agglomerated
Last Answer : d) Agglomerated
Description : Which of the following defects is usually associated with the MAG GMAW) welding process when using Dip Transfer? a) Centerline cracking b) Lack of side wall Fusion c) Undercut d) Tungsten inclusions
Last Answer : b) Lack of side wall Fusion
Description : When welding medium carbon steel plates over 100mm in thickness would the basic electrodes require any pre treatment before use? a) None if they were in a vacuum pack opened 8 hours prior to use b) None if ... ) Heat to 500 °C for 2 hours if used outside d) Baked at 150°C for 4hours prior to use
Last Answer : b) None if they were in a sealed vacuum pack prior to use
Description : Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps
Last Answer : a) MAG (GMAW)
Description : What is the mode of metal transfer for the TIG (GTAW) welding process? a) Spray Transfer b) Globular Transfer c) Dip Transfer d) None of the above
Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable
Last Answer : b) Higher deposition rate
Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V
Last Answer : c) 10-12V
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2
Last Answer : b) 333N/mm2
Description : Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder ... welding is always carried out to a high standard the use of percentage NDT is of no real value
Last Answer : c) This will be referenced in the inspection and test plan
Description : What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name
Last Answer : c) Welder’s Identification, date and weld number
Description : Why is the OCV capped at voltage setting? a) To save electricity b) To prevent exploding of the consumable c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality
Last Answer : c) Allow smooth transition into welding voltage range
Description : The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider
Last Answer : d) The weld width would be wider
Description : During root welding, which of the following would be the main cause of excess penetration? a) The root gap is too small in accordance with WPS b) Preheat not used c) The current is too high d) Root face is too large
Last Answer : c) The current is too high
Description : When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is ... preheat temperature measurement is only required if the heat input is lower than that specified in WPS
Last Answer : b) Immediately prior to commencing the first pass and subsequent passes
Description : What BSEN standard is used for welding symbols on drawings? a) BS EN 970 b) BS EN 287 c) BS EN 22553 d) BS EN 4515
Last Answer : c) BS EN 22553