Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?

Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?
by

1 Answer

Answer :

If the wall is an interior wall then it should be an empty cavity. If it is an old home you may have fire stops inside the walls that will be a dead end when you attempt to fish the wire down. Make a new hole for the new switch leg and leave the old one in the wall unless you just have to yank the old wire out. If the switch is on an outside wall then you will have to deal with wall insulation in the way. The old sconce, its going to be eliminated? It will be a good idea to know how much load is already on the circuit if you want to still use the sconce.
by

Related questions

Wiring – types

Description : Wiring – types

Last Answer : Ans) a. Casing & Capping b. Concealed wiring c. Cleat Wiring d. Conduit Wiring – Cutting of wall.

How to replace the electrical wiring in the apartment?

Description : How to replace the electrical wiring in the apartment?

Last Answer : How to replace the electrical wiring in the apartment? In most cases, when renovating an apartment, a complete replacement of the electrical wiring is required, especially if the house was built in ... Upon completion of the finishing, the new electrical wiring in your apartment is ready for use.

Compare casing capping wiring with concealed wiring.

Description : Compare casing capping wiring with concealed wiring.

Last Answer : Compare casing capping wiring with concealed wiring: 

State different types of holders used in wiring installation.

Description : State different types of holders used in wiring installation.

Last Answer : Following types of holders used in wiring installation: 1. Pendent Holder 2. Batten Holder 3. Angle holder 4. Screwed holder 

Illustrate with neat wiring diagram a single lamp control by two point method.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Name safety tools used in industry for electrical wiring.

Description : Name safety tools used in industry for electrical wiring.

Last Answer : Safety tools used in industry for electrical wiring : 1) Hand gloves 2) Goggles 3) Rubber mats 4) Fire extinguishers 5) Danger notice plates 6) Search lights 7) Safety shoes or Gumboots 8) Ear plugs ... belts 13) Safety mask 14) Fire buckets 15) First aid box 16) Insulating stick or discharge rod

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

List any four wiring accessories and its function.

Description : List any four wiring accessories and its function. 

Last Answer : Following wiring accessories: 1) Lamp holder: It is the holding accessory. The different types of holders used such as angle holder, batten holder, pendent holder 2) Ceiling Rose: Ceiling rose are of two types: ... etc 9) Switch board, ICDP Main Switch 10) All types of size of VIR & PVC wire

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

We are installing antique sconces on the walls of our dining room.

Description : We are installing antique sconces on the walls of our dining room.

Last Answer : answer:I come to you from the future…sconces will be out of style in three years. DON’T DO IT

Can we put different perfumes in wires so that we can tell which ones are burning?

Description : Can we put different perfumes in wires so that we can tell which ones are burning?

Last Answer : It is unlikely that a burning wire could reliably activate the base fragrance. It might just as likely burn the fragrance off. Not everyone can distinguish smells as reliably or accurately. There are other ... my father was always able to tell if a circuit was active or if a battery was charged.

Ceiling Light Fixture?

Description : Ceiling Light Fixture?

Last Answer : form_title= Ceiling Light Fixture form_header= Light up your life with a ceiling light fixture. What is the height of your ceiling?*= _ [50] Do you want to include a ceiling fan? How many light fixtures do you need installed?*= {1, 2, 3, 4, 5, More than 5}

How to Install a Wall Sconce

Description : How to Install a Wall Sconce

Last Answer : How to Install a Wall Sconce Regular wall light fixtures are great, but if you're looking for one that can provide you with a low illumination level, and make the area seem larger than it is, then ... from reading how to replace a light switch and as a bonus learn how to make a landscape lighting.

Coast Guard Regulations (46 CFR) require that lighting fixture globes must be protected by guards if the fixtures are located in the ____________. A. steering gear room B. galley C. living quarters D. wheelhouse

Description : Coast Guard Regulations (46 CFR) require that lighting fixture globes must be protected by guards if the fixtures are located in the ____________. A. steering gear room B. galley C. living quarters D. wheelhouse

Last Answer : Answer: A

Is it normal for a light bulb to break and hang from the light fixture by a wire?

Description : Is it normal for a light bulb to break and hang from the light fixture by a wire?

Last Answer : answer:Incandescent bulbs? If so, then yes, they often do that. Turn off the light switch when unscrewing them. If you can’t get the base out, a potato (or in my case a pliers) can assist in getting out the remains. Did you by any chance buy really cheap bulbs?

How to find 120v double contact bayonet light bulbs for an antique light fixture from Australia?

Description : How to find 120v double contact bayonet light bulbs for an antique light fixture from Australia?

Last Answer : I’d bet that the lamp uses bulbs based on the British standard. Chances are good that it takes a BA22d bulb. This was the only one commonly used for domestic lighting, and the base diameter (22mm) is right.

Is it easy enough to change an electric light fixture that I can do it without hiring a contractor?

Description : Is it easy enough to change an electric light fixture that I can do it without hiring a contractor?

Last Answer : It can be dangerous my dad does it but you need to turn the power off.

How to Replace an Exterior Light Fixture?

Description : How to Replace an Exterior Light Fixture?

Last Answer : How to Replace an Exterior Light FixtureReplacing an exterior light fixture is not difficult at all and you can do it even if you have limited electrical experience.Cutting the PowerBefore you do any ... . Turn the power back on at the circuit breaker box and test your new fixture connection.

What is the best way to light a living room with a high ceiling?

Description : What is the best way to light a living room with a high ceiling?

Last Answer : Metal stands with flaming torches. :-)

Will wall lights put off enough light to light a room with no center ceiling light source>?

Description : Will wall lights put off enough light to light a room with no center ceiling light source>?

Last Answer : There are different styles of lighting available. Choose something that will brighten up your room. There are many choices to choose from that you can really find something that is well-suited to your lighting needs.

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

Do you remember the smelly green modeling clay that was a fixture of my youth, and is it still available?

Description : Do you remember the smelly green modeling clay that was a fixture of my youth, and is it still available?

Last Answer : I had to make a model of the human brain with that stuff. Went straight into the garbage after it was marked.

What do you call the fixture that cooks use to hang things from?

Description : What do you call the fixture that cooks use to hang things from?

Last Answer : Pot racks

Mark the incorrect option a) The articles of stock such as plant and machinery, furniture and fixture are classed as “Dead stock” b) Consumable and perishable articles come under the term “Stores” c) Both the A and B d) None of these

Description : Mark the incorrect option a) The articles of stock such as plant and machinery, furniture and fixture are classed as “Dead stock” b) Consumable and perishable articles come under the term “Stores” c) Both the A and B d) None of these

Last Answer : d) None of these

Which type of splice is used to splice a lighting fixture to a branch circuit?

Description : Which type of splice is used to splice a lighting fixture to a branch circuit?

Last Answer : Fixture joint.

Explain general principles of jigs/fixture design

Description : Explain general principles of jigs/fixture design

Last Answer : 1. Before planning the design of a tool, compare the cost of production of the work with present tools with the expected cost of production, using the tool to be made. Confirm that the cost of ... nearly as possible opposite to some bearing point of the work to avoid springing. 11. Round all corners

Enlist general principle of jig and fixture design.

Description : Enlist general principle of jig and fixture design.

Last Answer : General principle of jig and fixture design. 1. The jig and fixture should be as open as possible to minimize chip or burr accumulation and to enable the operator to remove the chips easily with a ... . Inserts 9. Design for safety 10. Sighting surfaces 11. Simplicity in Design 12. Economical 

Draw the labelled sketch of turning fixture.

Description : Draw the labelled sketch of turning fixture.

Last Answer : Figure: Back plate of Turning Fixture

State at least eight principles of jigs/ fixture design

Description : State at least eight principles of jigs/ fixture design

Last Answer : The following principles should be considered for design of jigs/ fixtures 1.Rigidity: jigs/ fixtures should be sufficiently stiff/rigid to achieve required accuracy during machining. 2.Fool ... or clearance grooves should be provided for easy removal of metal chips, burrs after machining

Differentiate in between Jig and fixture.

Description : Differentiate in between Jig and fixture.

Last Answer : Difference between jig and fixture. 

What's the best color to paint a room with a slanted ceiling?

Description : What's the best color to paint a room with a slanted ceiling?

Last Answer : beige or lite sunny yellow

Does using a ceiling fan make a hot room warmer or cooler?

Description : Does using a ceiling fan make a hot room warmer or cooler?

Last Answer : the air it’s blowing might be hot but the wind it creates blows your body heat away from your body making you feel cooler I think

Two cops walked into a room with no windows and found a dead man who obviously hung himself from the ceiling, though they couldn't figure out how. There was no chair beneath him that he might have jumped off of, or a table. Just a puddle of water. How'd he do it? -Riddles

Description : Two cops walked into a room with no windows and found a dead man who obviously hung himself from the ceiling, though they couldn't figure out how. There was no chair beneath him that he might have jumped off of, or a table. Just a puddle of water. How'd he do it? -Riddles

Last Answer : He stood on a block of ice until it melted.

You are in a room that is completely bricked in on all four sides, including the ceiling and floor. You have nothing but a mirror and a wooden table in the room with you. How do you get out? -Riddles

Description : You are in a room that is completely bricked in on all four sides, including the ceiling and floor. You have nothing but a mirror and a wooden table in the room with you. How do you get out? -Riddles

Last Answer : You look in the mirror you see what you saw, you take the saw and you cut the table in half, two halves make a whole, and you climb out the hole.

The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and the ceiling at the rate of ₹7.50 m². -Maths 9th

Description : The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and the ceiling at the rate of ₹7.50 m². -Maths 9th

Last Answer : Length of a room (l) = 5m Breadth (b) = 4 m and height (h) = 3 m ∴ Area of 4 walls = 2(l + b) x h = 2(5 + 4) x 3 = 6 x 9 = 54 m² and area of ceiling = l x b = 5 x ... ∴ Total area = 54 + 20 = 74 m2 Rate of white washing = 7.50 per m² ∴ Total cost = ₹74 x 7.50 = ₹555

The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and ceiling at the rate of Rs 7.50 per m2. -Maths 9th

Description : The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and ceiling at the rate of Rs 7.50 per m2. -Maths 9th

Last Answer : Length (l) of room = 5m Breadth (b) of room = 4m Height (h) of room = 3m It can be observed that four walls and the ceiling of the room are to be white washed. Total area to be white washed = Area of walls + ... m2 area = Rs.7.50 (Given) Cost of white washing 74 m2 area = Rs. (74 7.50) = Rs. 555

Why is the warmest part of the room near the ceiling?

Description : Why is the warmest part of the room near the ceiling?

Last Answer : What is the answer ?

Ventilators are provided near the ceiling of the room because – (1) the exhaled warmer air rises up and goes out (2) these provide cross ventilation in the room (3) these provide some sunlight in the room (4) these do not look nice in the lower part

Description : Ventilators are provided near the ceiling of the room because – (1) the exhaled warmer air rises up and goes out (2) these provide cross ventilation in the room (3) these provide some sunlight in the room (4) these do not look nice in the lower part

Last Answer : (1) the exhaled warmer air rises up and goes out Explanation: Ventilation is a room air distribution strategy where conditioned outdoor air is supplied at floor level and extracted above the occupied zone, ... to heat exchange with heat sources in the space (e.g., occupants, computers, lights).

Ventilators are provided near the ceiling of the room because (1) the exhaled warmer air rises up and goes out (2) these provide cross ventilation in the room (3) these provide some sunlight in the room (4) these do not look nice in the lower part

Description : Ventilators are provided near the ceiling of the room because (1) the exhaled warmer air rises up and goes out (2) these provide cross ventilation in the room (3) these provide some sunlight in the room (4) these do not look nice in the lower part

Last Answer : the exhaled warmer air rises up and goes out

2006 Chrysler Sebring Fog Light Wiring harness....question.

Description : 2006 Chrysler Sebring Fog Light Wiring harness....question.

Last Answer : Just find out where the switch is on a model that’s got fog lights. Go to the dealer, buy the switch and install it where it’s supposed to go. Like the fog lights, the wiring for the switch should already be there.

how do i install 2-way light switch with old knob and tube wiring

Description : how do i install 2-way light switch with old knob and tube wiring

Last Answer : Need Answer

A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Description : A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Last Answer : Answer: B

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

What is the amount of sound reduction provided by a barrier – wall, floor, or ceiling called? A. Sound Attenuation B. Transmission loss C. Sound absorption D. Barrier loss

Description : What is the amount of sound reduction provided by a barrier – wall, floor, or ceiling called? A. Sound Attenuation B. Transmission loss C. Sound absorption D. Barrier loss

Last Answer : B. Transmission loss

Have you ever had the wrong advice from a computer technical support worker?

Description : Have you ever had the wrong advice from a computer technical support worker?

Last Answer : Carbonite. $80 a year. They back your stuff up.

I need to build a website for my sports club, can anyone give me good technical advice?

Description : I need to build a website for my sports club, can anyone give me good technical advice?

Last Answer : What are your current skills? Is there any budget to get in a professional? If your forced to go it alone the bare minimum you should consider learning is html, css and a little photoshop. I can ... . You could also check out sites like Template Monster and just buy and modify a design you like.

A marketer of industrial cleaning equipment is creating a marketing mix to satisfy potential customers. As a business to business marketer which of the following is LEAST likely to be included in the company's marketing mix? A)Machine servicing B)A higher price for higher -quality products C)Technical advice about the product D)Credit extension E)Extensive television advertising

Description : A marketer of industrial cleaning equipment is creating a marketing mix to satisfy potential customers. As a business to business marketer which of the following is LEAST likely to be ... -quality products C)Technical advice about the product D)Credit extension E)Extensive television advertising

Last Answer : E)Extensive television advertising

Marsha Hemlock, a trained engineer, is a salesperson for a chemical manufacturer. She provides current customers with advice about a product's characteristics and applications. She is a A)missionary salesperson. B)trade salesperson. C)field order taker. D)inside order taker. E)technical salesperson.

Description : Marsha Hemlock, a trained engineer, is a salesperson for a chemical manufacturer. She provides current customers with advice about a product's characteristics and applications. She is a A)missionary salesperson. B)trade salesperson. C)field order taker. D)inside order taker. E)technical salesperson.

Last Answer : E)technical salesperson.

How do I nicely tell my already-shunned best friend that there's no room for her in my New Year's Eve plans?

Description : How do I nicely tell my already-shunned best friend that there's no room for her in my New Year's Eve plans?

Last Answer : Tell her flat out you and your sweetie would love to spend time with her at lunch or at some other time, but that night you are happily booked ;)