In v/f control method,

In v/f control method, 

 (a) The maximum torque decreases (b) The motor speed increases (c) The maximum torque is constant (d) The maximum torque increases
by

1 Answer

Answer :

In v/f control method, The maximum torque is constant 

by

Related questions

For speed control of ac drive, the preferred method using thyristors is

Description : For speed control of ac drive, the preferred method using thyristors is  A) Phase control B) Integral cycle control C) Single pulse PWM control D) Sinusoidal PWM control

Last Answer : For speed control of ac drive, the preferred method using thyristors is Sinusoidal PWM control

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and

Description : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

Last Answer : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is First

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

In a thyistorised converter a free wheeling diode is used to

Description : In a thyistorised converter a free wheeling diode is used to  A) Add to the conduction current ofthe thyristor B) Oppose the thyristor conduction C) Conduct current during the off period of the thyristor D) Protect the thyristor by providing a shunt path

Last Answer : In a thyistorised converter a free wheeling diode is used to Conduct current during the off period of the thyristor

In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Description : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Last Answer : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying T, keeping ton constant

The ripple factor of a bridge rectifier is

Description : The ripple factor of a bridge rectifier is  1.0.48 2.0.812 3. 1.11 4. 1.21 

Last Answer : The ripple factor of a bridge rectifier is 0.48

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply

Description : A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% ... to the DC supply is  (a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

Last Answer : 48

In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is

Description : In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is   (a) 0.633 (b) 0.533 (c) 0.833 (d) 0.733 

Last Answer : In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is 0.833

Specific energy consumption of an electric train is the ratio between

Description : Specific energy consumption of an electric train is the ratio between (A) Specific energy output at driving wheels and efficiency of the traction motor (B) Specific energy output at driving wheels ... (D) Specific energy output at driving wheels and efficiency of the (motor + transmission gear)

Last Answer : Specific energy consumption of an electric train is the ratio between Specific energy output at driving wheels and efficiency of the (motor + transmission gear)

In electric traction for a trapezoidal speed-time curve, the time period is

Description : In electric traction for a trapezoidal speed-time curve, the time period is (A) free running speed period = constant speed period (B) free running period = coasting period (C) free running period + coasting period = constant speed period (D) average speed period = scheduled speed period

Last Answer : In electric traction for a trapezoidal speed-time curve, the time period is free running period + coasting period = constant speed period

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

The direction of rotation of an inverter fed 3-phase ac motor is reversed by

Description : The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

Last Answer : The direction of rotation of an inverter fed 3-phase ac motor is reversed by changing the sequence of switching

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up

Description : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

Last Answer : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is 9997 Ω

RC triggering is preferred over resistance triggering because

Description : RC triggering is preferred over resistance triggering because (A) it provides triggering at a precise instant (B) it gives a longer duration gate pulse (C) it enables triggering at a larger value of firing angle (D) it protects the SCR against high dv/dt

Last Answer : a

In an adjustable speed ac drive which quantity gets reduced above rated speed ?

Description : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Last Answer : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Slip-Energy Recovery (SER) scheme for three phase Induction Motor

Description : Slip-Energy Recovery (SER) scheme for three phase Induction Motor

Last Answer : Slip-Energy Recovery (SER) scheme for three phase Induction Motor

Scherbius Drive System

Description : Scherbius Drive System

Last Answer : Scherbius Drive System

Kramer Drive System

Description : Kramer Drive System

Last Answer : Kramer Drive System Kramer drive is a rotor side speed control drive of induction motor. Slip is the difference between synchronous speed and rotor speed. It is the ... and DC motor. The static Kramer drive is costlier because of the cost of DC motor.

Chopper controlled DC motor

Description : Chopper controlled DC motor

Last Answer : Chopper controlled DC motor

What are the advantages of V/F control?

Description : What are the advantages of V/F control?

Last Answer : 1. Smooth speed control 2. Small input current and improved power factor at low-frequency start 3. Higher starting torque for low case resistance

What is meant by V/F control?

Description : What is meant by V/F control?

Last Answer : When the frequency is reduced, the input voltage must be reduced proportionally so as to maintain constant flux. Otherwise the core will get saturated resulting in excessive iron loss and magnetizing current. This type of induction motor behaviour is similar to the working of dc series motors.

For V/F control, when frequency is increased in transformer a) Core loss component current increases, Magnetizing component current decreases b) Core loss component current increases, Magnetizing component current increases c) Core loss component current decreases, Magnetizing component current decreases d) Core loss component current decreases, Magnetizing component current increases

Description : For V/F control, when frequency is increased in transformer a) Core loss component current increases, Magnetizing component current decreases b) Core loss component current increases, ... component current decreases d) Core loss component current decreases, Magnetizing component current increases

Last Answer : Ans: Core loss component current decreases, Magnetizing component current decreases

In ΔABC and ΔDEF, AB = DE, AB || DE, BC = EF and BC || EF. Vertices A, B and C are joined to vertices D, E and F respectively (see Fig. 8.22). Show that (i) quadrilateral ABED is a parallelogram (ii) quadrilateral BEFC is a parallelogram (iii) AD || CF and AD = CF (iv) quadrilateral ACFD is a parallelogram (v) AC = DF (vi) ΔABC ≅ ΔDEF. -Maths 9th

Description : In ΔABC and ΔDEF, AB = DE, AB || DE, BC = EF and BC || EF. Vertices A, B and C are joined to vertices D, E and F respectively (see Fig. 8.22). Show that (i) quadrilateral ABED is a parallelogram ( ... CF and AD = CF (iv) quadrilateral ACFD is a parallelogram (v) AC = DF (vi) ΔABC ≅ ΔDEF. -Maths 9th

Last Answer : . Solution: (i) AB = DE and AB || DE (Given) Two opposite sides of a quadrilateral are equal and parallel to each other. Thus, quadrilateral ABED is a parallelogram (ii) Again BC = EF and BC || EF ... (Given) BC = EF (Given) AC = DF (Opposite sides of a parallelogram) , ΔABC ≅ ΔDEF [SSS congruency]

Draw the ray diagram in each case to show the position and nature of the image formed when the object is placed: (i) at the centre of curvature of a concave mirror (ii) between the pole P and focus F of a concave mirror (iii) in front of a convex mirror (iv) at 2F of a convex lens (v) in front of a concave lens -Physics

Description : Draw the ray diagram in each case to show the position and nature of the image formed when the object is placed: (i) at the centre of curvature of a concave mirror (ii) between the pole P and focus F of ... front of a convex mirror (iv) at 2F of a convex lens (v) in front of a concave lens -Physics

Last Answer : Answer. Nature of image: Real, inverted and same size image is formed at the centre of curvature. Nature of image: Virtual, enlarged and erect image is formed behind the mirror. Nature of image: Virtual ... : Virtual, erect and diminished image is formed between O and F on the same side of object.

A wall is moving with constant velocity `u` towards a fixed source of sound of frequency `f`. The velocity of sound is `v`. The wavelength of the soun

Description : A wall is moving with constant velocity `u` towards a fixed source of sound of frequency `f`. The velocity of sound is `v`. The wavelength of the soun

Last Answer : A wall is moving with constant velocity `u` towards a fixed source of sound of frequency `f`. The velocity of sound is ` ... C. `(v-u)/f` D. `(v+u)/f`

An adsorption isotherm equation proposed by Langmuir is of the form `V = (V_(0)bPO)/((1 + bP))` where V is the volume of gas adsorbed at pressure P. F

Description : An adsorption isotherm equation proposed by Langmuir is of the form `V = (V_(0)bPO)/((1 + bP))` where V is the volume of gas adsorbed at pressure P. F

Last Answer : An adsorption isotherm equation proposed by Langmuir is of the form `V = (V_(0)bPO)/((1 + bP))` where V is ... of V on P can be depicted as B. C. D.

A battery of e.m.f. `10 V` is connected to resistance as shown in figure. The potential difference `V_(A) - V_(B)` between the point `A` and `B` is

Description : A battery of e.m.f. `10 V` is connected to resistance as shown in figure. The potential difference `V_(A) - V_(B)` between the point `A` and `B` is

Last Answer : A battery of e.m.f. `10 V` is connected to resistance as shown in figure. The potential difference `V_(A) - V_(B) ... -2V` B. 2V C. 5V D. `(20)/(11)V`

For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is shunted by a `2Omega` resistor and the balance is

Description : For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is shunted by a `2Omega` resistor and the balance is

Last Answer : For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is ... B. `0.50Omega` C. `0.80Omega` D. `1.00Omega`

Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the internal resistance of battery A is 1.9

Description : Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the internal resistance of battery A is 1.9

Last Answer : Two batteries A and B each of e.m.f. 2 V are connected in series to an external resistance R = 1 ohm . If the ... V B. `3.8` V C. zero D. `4.8` V

A resistance of `4 Omega` and a wire of length 5 meters and resistance `5 Omega` are joined in series and connected to a cell of e.m.f. `10 V` and int

Description : A resistance of `4 Omega` and a wire of length 5 meters and resistance `5 Omega` are joined in series and connected to a cell of e.m.f. `10 V` and int

Last Answer : A resistance of `4 Omega` and a wire of length 5 meters and resistance `5 Omega` are joined in series and connected ... `3.0V` C. `0.67V` D. `1.33V`

Does pressing F while full speed in GTA V give you a speed boost?

Description : Does pressing F while full speed in GTA V give you a speed boost?

Last Answer : Yes, if you advance to full speed in any terrain vehicle in GTA V, you will gain an extra speed boost. Make sure you are going full speed though.

According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Description : According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Last Answer : (B) √(S/V)

A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Description : A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Last Answer : 0.06 V

If frequency of certain wave is f, then it's velocity is A. v = fλ B. v = T⁄λ C. T2 D. 1⁄T2

Description :  If frequency of certain wave is f, then it's velocity is A. v = fλ B. v = T⁄λ C. T2 D. 1⁄T2

Last Answer : v = fλ

Cellular totipotency was demonstrated by (a) Theodore Schwann (b) A.V. Leeuwenhoek (c) F.C. Steward (d) Robert Hooke.

Description : Cellular totipotency was demonstrated by (a) Theodore Schwann (b) A.V. Leeuwenhoek (c) F.C. Steward (d) Robert Hooke.

Last Answer : (c) F.C. Steward

For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3 ), while the C.V. is same on weight basis (i.e., kcal/kg)? (A) Propane and acetylene (B) Propane and LPG (C) Sewage gas and gobar gas (D) B.F. gas and coke oven gas

Description : For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3 ), while the C.V. is same on weight basis (i.e., kcal/kg)? (A) Propane and acetylene (B) Propane and LPG (C) Sewage gas and gobar gas (D) B.F. gas and coke oven gas

Last Answer : (A) Propane and acetylene

A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume of the reacting mixture is V and the density of the liquid mixture is constant. The mass balance for A is (A) d(VCA )/dt = -F (CAF - CA ) - kCA 2V (B) d(VCA )/dt = F (CAF - CA ) - kCA 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Description : A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume ... 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Last Answer : (D) d(VCA )/dt = FCAF - kCA 2V

Which of the following pair is incorrect: a) Cut - CTRL + X b) Copy - CTRL + C c) Paste - CTRL + V d) Select All - CTRL + A e) Find - CTRL + F f) Undo -CTRL + Z g) None of These h) All of Above

Description : Which of the following pair is incorrect: a) Cut - CTRL + X b) Copy - CTRL + C c) Paste - CTRL + V d) Select All - CTRL + A e) Find - CTRL + F f) Undo -CTRL + Z g) None of These h) All of Above

Last Answer : g) None of These

For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)? (A) Propane and acetylene (B) Propane and LPG (C) Sewage gas and gobar gas (D) B.F gas and coke oven gas

Description : For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)? (A ... and acetylene (B) Propane and LPG (C) Sewage gas and gobar gas (D) B.F gas and coke oven gas

Last Answer : D) B.F gas and coke oven gas

For calculating the evaporation rate over a reservoir surface E = 0.771 (1.465 - 0.00732B) (0.44 - 0.007375 V) (pe - pa), the equation is given by (A) Roohwer's, formula in M.K.S. (B) Roohwer's formula in F.P.S. (C) Dalton's formula in F.P.S. (D) Dalton's formula in M.K.S

Description : For calculating the evaporation rate over a reservoir surface E = 0.771 (1.465 - 0.00732B) (0.44 - 0.007375 V) (pe - pa), the equation is given by (A) Roohwer's, formula in M.K.S. (B) Roohwer's formula in F.P.S. (C) Dalton's formula in F.P.S. (D) Dalton's formula in M.K.S

Last Answer : Answer: Option A

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

In dielectric measurement, the dielectric loss is proportional to a) F b) V c) I d) Vsqr

Description : In dielectric measurement, the dielectric loss is proportional to a) F b) V c) I d) Vsqr

Last Answer : Ans: Vsqr

If we convert ∃u ∀v ∀x ∃y (P(f(u),v, x, y) → Q(u,v,y)) to ∀v ∀x (P(f(a),v, x, g(v,x)) → Q(a,v,g(v,x))) This process is known as (A) Simplification (B) Unification (C) Skolemization (D) Resolution

Description : If we convert ∃u ∀v ∀x ∃y (P(f(u),v, x, y) → Q(u,v,y)) to ∀v ∀x (P(f(a),v, x, g(v,x)) → Q(a,v,g(v,x))) This process is known as (A) Simplification (B) Unification (C) Skolemization (D) Resolution

Last Answer : (C) Skolemization

Consider a system with seven processes A through G and six resources R through W. Resource ownership is as follows: process A holds R and wants T process B holds nothing but wants T process C holds nothing but wants S process D holds U and wants S & T process E holds T and wants V process F holds W and wants S process G holds V and wants U Is the system deadlocked ? If yes, ............. processes are deadlocked. (A) No (B) Yes, A, B, C (C) Yes, D, E, G (D) Yes, A, B, F

Description : Consider a system with seven processes A through G and six resources R through W. Resource ownership is as follows: process A holds R and wants T process B holds nothing but wants T process C holds nothing but wants S process D holds U ... No (B) Yes, A, B, C (C) Yes, D, E, G (D) Yes, A, B, F

Last Answer : (C) Yes, D, E, G

If the load p.f. is 0.866, then the average p.f. the v-bank is

Description : If the load p.f. is 0.866, then the average p.f. the v-bank is  1. 0.886  2. 0.75  3. 0.51  4. 0.65 

Last Answer : If the load p.f. is 0.866, then the average p.f. the v-bank is 0.75 

In a variable speed induction motor derive V/f kept constant over a wide range of its frequency variation. ...

Description :  In a variable speed induction motor derive V/f kept constant over a wide range of its frequency variation. The motor operates in the following mode : -  a) Constant power mode b) Constant torque mode c) Constant slip mode d) Variable power and variable torque mode

Last Answer :  In a variable speed induction motor derive V/f kept constant over a wide range of its frequency variation. The motor operates in the following mode : - Constant torque mode

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm...

Description : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

Last Answer : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be 580 V.

A shunt generator running at 1000 r.p.m. has generated e.m.f. as 200 V. If the speed increases to 1200 r.p.m...

Description : A shunt generator running at 1000 r.p.m. has generated e.m.f. as 200 V. If the speed increases to 1200 r.p.m., the generated e.m.f. will be nearly?

Last Answer : 200V/E2 = 1000/1200 E2= 240 V

If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by?

Last Answer : If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by Blv.