State advantages of MOSFET over JFET.

State advantages of MOSFET over JFET.
by

1 Answer

Answer :

➨It can be operated in either enhancement mode or depletion mode.

➨MOSFET have much higher input impedance compare to JFET.

➨They have high drain resistance due to lower resistance of channel.

➨It is easy to manufacture.

➨They support high speed of operation compare to JFETs.
by

Related questions

State advantages of MOSFET.

Description : State advantages of MOSFET.

Last Answer : Advantages of MOSFET * MOSFETs provide greater efficiency while operating at lower voltages. * Absence of gate current results in high input impedance. * High switching speed. * They operate at lower ... due to lower resistance of channel. * They are easy to manufacture. * They are portable.

Sketch construction of N-channel JFET and explain its operating principle.

Description : Sketch construction of N-channel JFET and explain its operating principle.

Last Answer : Construction of N-channel JFET: Working of N channel FET: a)when VGS is zero,ID flows because of VDS b)Now when VGS increases towards negative, depletion layer also increases on both sides. c)so VGS control drain current ID d)so it is called as field effect Transistor

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Description : Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Last Answer : C. MESFET

The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Description : The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Last Answer : D. MESFET

When compared to the JFET, what is the input impedance of the MOSFET?

Description : When compared to the JFET, what is the input impedance of the MOSFET?

Last Answer : The MOSFET has a higher input impedance.

Compare JFET with MOSFET.

Description : Compare JFET with MOSFET.

Last Answer : Particulars JFET MOSFET 1) Type Voltage controlled device Voltage controlled device 2) Mode of operation Operates only in depletion mode Operates in depletion and enhancement ... 6) Gate connection Not isolated from substrate Isolated by SiO2 layer from substrate

A depletion MOSFET differs from a JFET in the sense that it has no

Description : A depletion MOSFET differs from a JFET in the sense that it has no   (A) channel (B) gate (C) P-N junctions (D) substrate

Last Answer : A depletion MOSFET differs from a JFET in the sense that it has no P-N junctions 

State 2 advantages of JFET over BJT.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

Explain with circuit diagram, voltage divider biasing method and state its two advantages.

Description : Explain with circuit diagram, voltage divider biasing method and state its two advantages.

Last Answer : a)Here R1 and R2 forms voltage divider biasing arrangement. b)voltage drop across R2 ,forward biases the base emitter junction. c)so base current flows and hence collector ... Operating point stabilized against shift in temperature. · Operating point is almost independent of β variation

The seven segment arrangement for numerical display on consoles, test meters and other applications can be either ________________. A. UJT or BJT B. BCD or OCD C. JFET or IGFET D. LED or LCD

Description : The seven segment arrangement for numerical display on consoles, test meters and other applications can be either ________________. A. UJT or BJT B. BCD or OCD C. JFET or IGFET D. LED or LCD

Last Answer : Answer: D

Why JFET is called a unipolar transistor?

Description : Why JFET is called a unipolar transistor?

Last Answer : In JFET, the current conduction is either by electrons or holes and controlled by means of an electric field between the gate electrode and the conducting channel of the device, So it is called as a unipolar transistor.

What is the importance of JFET?

Description : What is the importance of JFET?

Last Answer : A JFET acts like a voltage controlled device i.e. input voltage controls the output current. This is different from ordinary transistor where input current controls the output current. JFET has higher input impedance than that of a conventional transistor.

What is pinch off voltage in JFET?

Description : What is pinch off voltage in JFET?

Last Answer : Pinch off voltage (VP): It is the minimum drain source voltage at which the drain current essentially becomes constant.

What is JFET?

Description : What is JFET?

Last Answer : A junction FET is a three terminal semiconductor device in which current conduction is by one type of carrier (i.e.) electrons or holes.

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

What is the normal current path in an N-channel JFET?

Description : What is the normal current path in an N-channel JFET?

Last Answer : From source to drain.

The source and drain of an N-channel JFET are made of what type of material?

Description : The source and drain of an N-channel JFET are made of what type of material?

Last Answer : N-type material.

What are the two types of JFET?

Description : What are the two types of JFET?

Last Answer : N-channel and P-channel.

Draw the transfer characteristics for N-channel JFET.

Description : Draw the transfer characteristics for N-channel JFET.

Last Answer : Transfer characteristics for N-channel JFET: 

Sketch p-channel JFET construction.

Description : Sketch p-channel JFET construction.

Last Answer : p- channel JFET constructional diagram:

Define junction field effect transistor (JFET) and give an example.

Description : Define junction field effect transistor (JFET) and give an example.

Last Answer : Junction Field-Effect Transistor: It is a semiconductor device having three terminals, namely Gate, Drain and Source, in which the current flow is controlled by an electric field set up by an external voltage applied ... : i) n-channel JFET and ii) p-channel JFET Examples of JFET: BFW 10, BFW 11 

Describe operation of N-channel JFET

Description : Describe operation of N-channel JFET

Last Answer : Operation of N-channel JFET  1) When VGS = 0 volt: When a voltage is applied between the drain and source with a DC supply voltage VDD with VGS = 0 V, the electrons flow from source ... to zero. The gate to source voltage at which current reduces to zero is called as pinch-off voltage.

The transconductance of a JFET is computed at constant VDS by:

Description : The transconductance of a JFET is computed at constant VDS by: (1) Ratio of change in Idto change of Vgs (2) Ratio of change inVgs to change ofId (3) Product of change in Vgs to change of Id (4) Ratio of change in Vds to change of Id

Last Answer : The transconductance of a JFET is computed at constant VDS by: Ratio of change in Id to change of Vgs 

A JFET has the disadvantage of

Description : A JFET has the disadvantage of  1. Having low input impedance 2. Having high output impedance 3. Having small gain band-width product 4. Possessing positive temperature coefficient

Last Answer : A JFET has the disadvantage of Having small gain band-width product

The operation of a JFET involves

Description : The operation of a JFET involves  (A) A flow of minority carriers (B) a flow 0f majority carriers (C) recombination (D) negative resistance

Last Answer : The operation of a JFET involves a flow 0f majority carriers 

The voltage gain of a common -source JFET amplifier depends up on its

Description : The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

Last Answer : B

While biasing JFET if drain and source are interchanged, then

Description : While biasing JFET if drain and source are interchanged, then (A) device will work normally (B) device will get damaged (C) device will work but value of drain current will affected (D) device will not operate at all

Last Answer : B

JFET in properly biased condition acts as a: ...

Description : JFET in properly biased condition acts as a:  (1) Current controlled current source (2) Voltage controlled voltage source (3) Voltage controlled current source (4) Impedance controlled current source

Last Answer : JFET in properly biased condition acts as a: Voltage controlled current source.

In a JFET drain current is maximum when VGS is...

Description : In a JFET drain current is maximum when VGS is  (a) zero (b) negative (c) positive (d) equal to Vp

Last Answer : A

The transit time of the current carriers through the channel of a JFET decides it's ?

Description : The transit time of the current carriers through the channel of a JFET decides it's?

Last Answer : The transit time of the current carriers through the channel of a JFET decides it's gate characteristics.

Define Transistor. State its type.

Description : Define Transistor. State its type.

Last Answer : Transistors are active electronic components made of semiconducting materials, which can amplify the electric signals by the application of a small input signal. Types of transistors: 1. Unipolar Junction Transistors 2. Bipolar Junction Transistors

Sketch constructional diagram of LED and state its three applications.

Description : Sketch constructional diagram of LED and state its three applications.

Last Answer : Applications of LED: .Infra-red LEDs are used in burglar alarm systems. · For solid state video displays which are rapidly replacing CRT. · An image sensing circuit for picture phones. · In array of different types for displaying alpha-numeric characters. · Displays.

State any four applications of regulated DC power supply.

Description : State any four applications of regulated DC power supply.

Last Answer : * Amplifiers * Mobile Phone power adaptors * Regulated power supplies in appliances * Various oscillators

State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Description : State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Last Answer : Application of resistor: 1.Resistors are used in high frequency instrument. 2.Resistor is used in power control circuit. 3.It is used in DC power supplies. 4.Resistors are used ... DC Current  3.Electromagnetic Interference (EMI)  4.Magnetic Saturation Flux Density  5.Curie Temperature 

State different types of electrical signal and draw all types of waveforms.

Description : State different types of electrical signal and draw all types of waveforms.

Last Answer : Types of electrical signals 1) Sine wave 2) Triangular wave 3) Square wave Waveforms

State the Barkhausen criteria of oscillations

Description : State the Barkhausen criteria of oscillations

Last Answer : Barkhausen's Criteria - To obtain sustain oscillation the loop gain AB = 1 and phase shift of feedback signal should be 00 or 3600 of an amplifier. it is called as barkshausen's ...  Wien bridge oscillator LC Oscillator  Hartley oscilator  Colpitts oscillator  Crystal oscillator

State the application of FET

Description : State the application of FET

Last Answer : Applications of FET : * As input amplifiers in oscilloscopes, electronic voltmeters and other measuring and testing equipment because high input impedance reduces loading effect to the minimum. * As Constant ... Used as Analog switch. * As a Voltage Variable Resistor (VVR) in operational amplifiers.

State reason BJT is called as bipolar junction transistor.

Description : State reason BJT is called as bipolar junction transistor.

Last Answer : BJT is called bipolar junction transistor because in BJT current conduction takes place due to majority as well as minority charge carriers.

State the types of filters.

Description : State the types of filters.

Last Answer : Types of filters: 1. Capacitor input filter (shunt capacitor filter) 2. Choke input filter (series inductor filter) 3. LC filter 4. π type filter OR CLC filter 5. RC filter.

why IGBT is preferred as a power switch over both power BJT and MOSFET?

Last Answer : Because it has a higher switching frequency and heat tolerance.

Draw the construction of p-channel D-MOSFET and state its working principle.

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

State the applications of MOSFET

Description : State the applications of MOSFET

Last Answer : Applications of MOSFET: i) Switching-mode-power-supplies (SMPS) and linear power supplies. ii) Brushless DC motor drives iii) Solid state DC relay iv) Automobile applications v) Stepper motor controller vi) Lighting controls vii) Solenoid drivers viii) Robotics ix) Induction heating

Steady state output i-v characteristics of a MOSFET

Last Answer : Steady state output i-v characteristics of a MOSFET   The MOSFET, like the BJT is a three terminal device where the voltage on the gate terminal controls the flow of current between the ... Distributed under Creative Commons Attribution-ShareAlike - CC BY-SA. Version 2 EE IIT, Kharagpur

Draw the symbol of photodiode.

Description : Draw the symbol of photodiode.

Last Answer : Symbol of photodiode.

Draw circuit diagram for π filter and explain its working with waveforms.

Description : Draw circuit diagram for π filter and explain its working with waveforms.

Last Answer : Working of a Pi filter: In this circuit, we have a capacitor in parallel, then an inductor in series, followed by another capacitor in parallel. Capacitor C1 − This filter capacitor ... any ac component present in the signal to pass through it, which the inductor has failed to block.

Sketch block diagram of an unregulated power supply and explain function of each block.

Description : Sketch block diagram of an unregulated power supply and explain function of each block.

Last Answer : Block diagram of regulated DC power supply:-  Explanation 1)Transformer 2) Rectifier 3) Filter 4) Voltage regulator. 1. Transformer:- Transformer can be step up ... a voltage regulator. Output of the regulator circuit will be constant voltage under all operating circumstances.

Define with respect to FET:- (i) Static drain resistance (ii) Dynamic resistance (iii) Trans conductance (iv) Pinch-off voltage

Description : Define with respect to FET:- (i) Static drain resistance (ii) Dynamic resistance (iii) Trans conductance (iv) Pinch-off voltage

Last Answer : (i) Static drain resistance- It is the ratio of drain source voltage (ΔVDS) to the drain current (ID) at constant gate-source voltage. It can be expressed as, Rd = (VDS)/(ID) at ... of charge carrier and the value of drain current reaches its constant saturation value is called pinch off voltage.

Sketch circuit diagram of positive biased clipper using diode and explain its working.

Description : Sketch circuit diagram of positive biased clipper using diode and explain its working.

Last Answer : Positive Series Clipper with positive Vr. The following figure represents the circuit diagram for positive series clipper when the reference voltage applied is positive. During the positive cycle ... Hence the input signal that is greater than the reference voltage, appears at the output.

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.