. In a MOSFET, which element is insulated from the channel material?

. In a MOSFET, which element is insulated from the channel  material?
by

1 Answer

Answer :

The gate terminal.
by

Related questions

The substrate of an N-channel MOSFET is made of what material?

Description : The substrate of an N-channel MOSFET is made of what material?

Last Answer : P-type material.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

What is the common name for enamel-insulated wire?

Description : What is the common name for enamel-insulated wire?

Last Answer : Magnet wire.

What safety precaution should you take when working with extruded polytetrafluoroethylene insulated wiring?

Description : What safety precaution should you take when working with extruded polytetrafluoroethylene insulated wiring?

Last Answer : Avoid breathing the vapors when the insulation is heated.

What is the purpose of the spring or wire around the leads of a new MOSFET?

Description : What is the purpose of the spring or wire around the leads of a new MOSFET?

Last Answer : To prevent damage from static electricity.

What type of MOSFET can be independently controlled by two separate signals?

Description : What type of MOSFET can be independently controlled by two separate signals?

Last Answer : The dual-gate MOSFET.

What are the four elements of the MOSFET?

Description : What are the four elements of the MOSFET?

Last Answer : Gate, source, drain, and substrate.

When compared to the JFET, what is the input impedance of the MOSFET?

Description : When compared to the JFET, what is the input impedance of the MOSFET?

Last Answer : The MOSFET has a higher input impedance.

A MOSFET can be damaged by an electrostatic discharge at approximately what minimum potential?

Description : A MOSFET can be damaged by an electrostatic discharge at approximately what minimum potential?

Last Answer : 35 volts.

Draw the construction of p-channel D-MOSFET and state its working principle.

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

Draw symbol for n-channel and p-channel MOSFET.

Description : Draw symbol for n-channel and p-channel MOSFET.

Last Answer : Symbol n-channel and p-channel MOSFET :   OR  

Describe the operation of N channel enhancement type MOSFET with diagram.

Description : Describe the operation of N channel enhancement type MOSFET with diagram.

Last Answer : As its name indicates, this MOSFET operates only in the enhancement mode and has no depletion mode. It operates with large positive gate voltage only. It does not conduct when the ... of charge carriers attracted to the positive gate. Thus drain current is controlled by the gate potential.

When does the Body bias effect occur in an n-channel MOSFET?

Description : When does the Body bias effect occur in an n-channel MOSFET?  A) When the Source voltage is less the Bulk voltage B) When the Source voltage is equal to or greater the Bulk voltage C) When the Drain voltage is equal to the Bulk voltage D) When the Gate voltage is equal to the Bulk Voltage 

Last Answer : When does the Body bias effect occur in an n-channel MOSFET?  A) When the Source voltage is less the Bulk voltage B) When the Source voltage is equal to or greater the Bulk voltage C) ... voltage is equal to the Bulk voltage D) When the Gate voltage is equal to the Bulk Voltage 

Assume that the n—channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V.

Description : Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is A)5V B)2V C)1V D)0V

Last Answer : Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is 0V

In a n-channel MOSFET, an inversion layer is

Description : In a n-channel MOSFET, an inversion layer is  (A) accumulation of electrons near the surface of the substrate under the gate  (B) accumulation of electrons near the drain  (C) accumulation of electrons near the surface  (D) accumulation of hole in the substrate

Last Answer : In a n-channel MOSFET, an inversion layer is accumulation of electrons near the surface of the substrate under the gate 

The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at

Description : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of (A) 1.5V (B) 2.5V (C) 3.5V (D) 4.5V

Last Answer : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of 2.5V

What is channel length modulation in MOSFET?

Description : What is channel length modulation in MOSFET?

Last Answer : Shortening of lenght of the inverted channel region with increase in drain bias for large drain biases due to which current increases with drain bias and output resistance decreases is called channel length modulation in MOSFET.

The source and drain of an N-channel JFET are made of what type of material?

Description : The source and drain of an N-channel JFET are made of what type of material?

Last Answer : N-type material.

In order to find the specific heat capacity of an unknown material a 50 g piece is heated to 80 degrees Celsius and fully immersed in a well insulated calorimeter filled with 100 g of water at 10 degr?

Description : In order to find the specific heat capacity of an unknown material a 50 g piece is heated to 80 degrees Celsius and fully immersed in a well insulated calorimeter filled with 100 g of water at 10 degr?

Last Answer : Assuming that the full question, which the questioner failed to post, is given in the Discussion, below.Taking the specific heat capacity of water as 4.2 Joules per gram per degree C, the metal has a specific heat capacity as approx 0.68 Joules/(g °C).

A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. Specific heat of block material is 0.4 kJ.kg-1. K-1. Ignoring the effect of expansion and contraction and also the heat capacity to tank, the total entropy change in kJ.kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Description : A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. ... .kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Last Answer : (B) 0

A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just next to pipe (i.e., inside) (B) The better insulating material should be put outside (C) Either of the insulating material could be put on either side (D) Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)

Description : A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just ... to which insulating material is to be put inside (i.e., just next to the pipe)

Last Answer : (A) The better insulation material should be put just next to pipe (i.e., inside)

A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will (A) Increase (B) Decrease (C) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Description : A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted ... ) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Last Answer : Option C

What is the normal current path in an N-channel JFET?

Description : What is the normal current path in an N-channel JFET?

Last Answer : From source to drain.

If a target is on the bearing axis of the radiated beam, what is the input to the bearing IF channel?

Description : If a target is on the bearing axis of the radiated beam, what is the input to the bearing IF channel?

Last Answer : Zero.

Tracks on each channel of a magnetic drum are grouped into what?

Description : Tracks on each channel of a magnetic drum are grouped into what?

Last Answer : Sectors.

What is a baseband communication channel like?

Description : What is a baseband communication channel like?

Last Answer : A party line

When aligning the trace with a short applied to channel A, which control should be adjusted to bring the trace parallel to the vertical axis?

Description : When aligning the trace with a short applied to channel A, which control should be adjusted to bring the trace parallel to the vertical axis?

Last Answer : TRACE ROTATE control.

Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Description : Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Last Answer : Amazon has a few. There are a lot of those tall narrow ones, but I saw a few more “portly” mugs.

How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Description : How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Last Answer : answer:Are you the only one closing in on ten thousand Lurve? That is impressive! I think the computer can survive in very low tempts.. Not sure about the rest. I’m an IT girl and I know we have the AC on the severs 24/7.

In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Description : In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Last Answer : Twisting the cables keep them close together so that, any external magnetic fields must cross both cable at the same time, so the interference created in one cable is cancelled by the almost exact opposite amount of interference in the other.

Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Description : Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Last Answer : 1. Twisted pair cable2. Crosstalk3. Radiowave4. Wired communication channel5. Resource sharing

Can a panel apartment be insulated?

Description : Can panel homes be insulated?

Last Answer : Thermal insulation is usually applied from the outside. If you are thinking of soundproofing, they are usually used with a soundproofing sponge. You can try, but I don’t think it will insulate much.

Should the house be insulated? 45 cm wall thickness

Description : The situation is that the wall thickness is 45 cm (ytong), we can not dismantle the insulated house. Thank you in advance for your help.

Last Answer : I supposedly don't need to insulate it anymore, its thermal insulation is so good, but if you don't have a problem doing it, I think you should do it. The good can be even better and will definitely pay off over the years. 

Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each wire carries a current I, respec

Description : Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each wire carries a current I, respec

Last Answer : Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each ... x C. y = x-1 D. y = -x+1

Where is the statement of all pipes connected to a storage vessel should be insulated for up to a metre in length is a requirement of Building Regulations Part?

Description : Where is the statement of all pipes connected to a storage vessel should be insulated for up to a metre in length is a requirement of Building Regulations Part?

Last Answer : P

Why are electric wires insulated?

Description : Why are electric wires insulated?

Last Answer : to keep the electricity into keep other things out (e.g. water, people, other wires)to prevent short circuits to nearby wiresto prevent electricutionto prevent firesetc.

Should copper pipes be insulated?

Description : Should copper pipes be insulated?

Last Answer : Insulating your copper pipes is a great idea. Insulating with foam will insure less heat loss which save energy and probably take a few bucks off your electricity bill.

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Last Answer : Answer: A

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the machine secured B. millivolt meter and a jumper with the machine running C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Last Answer : Answer: B

One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Description : One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Last Answer : Answer: D

One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Description : One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Last Answer : Answer: D

When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Description : When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Last Answer : Answer: B

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Description : When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Last Answer : Answer: D

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Description : In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Last Answer : Answer: B

A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Description : A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Last Answer : Answer: B

A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Description : A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Last Answer : Answer: D

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B