What does "tinning" mean in relationship to soldering?

What does "tinning" mean in relationship to soldering?
by

1 Answer

Answer :

The coating of the material to be soldered with a light coat of  solder.
by

Related questions

Why is steel wool NEVER used as an abrasive to clean soldering tools?

Description : Why is steel wool NEVER used as an abrasive to clean soldering tools?

Last Answer : The strands can fall into electrical equipment being worked on and cause short circuits.

What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Description : What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Last Answer : The soldering tips are hot only during the brief period of soldering the connection, thus minimizing the chance of burning the wire insulation or connector inserts.

A soldering gun should NOT be used on what components?

Description : A soldering gun should NOT be used on what components?

Last Answer : Electronic components, such as resistors, capacitors, and transistors.

Why are solvents used in the soldering process?

Description : Why are solvents used in the soldering process?

Last Answer : To remove contaminants from soldered connections.

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

What purpose does flux serve in the soldering process?

Description : What purpose does flux serve in the soldering process?

Last Answer : It cleans the metal by removing the oxide layer and prevents further oxidation during the soldering

What causes the nuts or screws that hold the tips on soldering irons and guns to loosen?

Description : What causes the nuts or screws that hold the tips on soldering irons and guns to loosen?

Last Answer : The heating and cooling cycles.

What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Description : What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Last Answer : It will overheat and could burn the insulation of the wire being soldered.

What should be done to a soldering iron tip that is pitted?

Description : What should be done to a soldering iron tip that is pitted?

Last Answer : File the tip until it is smooth and retin it.

State why a well-designed soldering iron is self-regulating

Description : State why a well-designed soldering iron is self-regulating

Last Answer : The resistance of its heating element increases with rising temperature, thus limiting the current flow.

Why are small-wattage soldering irons not used to solder large conductors?

Description : Why are small-wattage soldering irons not used to solder large conductors?

Last Answer : Although its temperature is as high as the larger irons, it does not have thermal inertia.

Why must items to be soldered be cleaned just prior to the soldering process?

Description : Why must items to be soldered be cleaned just prior to the soldering process?

Last Answer : Solder will not adhere to dirty, greasy, or oxidized surfaces.

How should excess solder be removed from a hot soldering iron?

Description : How should excess solder be removed from a hot soldering iron?

Last Answer : By use of a cleaning cloth.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

Flux aids in soldering by removing what from surfaces to be soldered?

Description : Flux aids in soldering by removing what from surfaces to be soldered?

Last Answer : Oxides.

In soldering, what alloy changes directly from a solid state to a liquid state?

Description : In soldering, what alloy changes directly from a solid state to a liquid state?

Last Answer : Eutectic.

How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Last Answer : Use a skipping pattern

What determines the shape and size of a soldering iron tip?

Description : What determines the shape and size of a soldering iron tip?

Last Answer : The type of work to be done.

What is the most common source of heat in electronic soldering?

Description : What is the most common source of heat in electronic soldering?

Last Answer : Conductive-type soldering iron.

The coating of a thin layer of zinc on steel or iron objects is known as – (1) Hot dipping (2) Tinning (3) Galvanising (4) Electroplating

Description : The coating of a thin layer of zinc on steel or iron objects is known as – (1) Hot dipping (2) Tinning (3) Galvanising (4) Electroplating

Last Answer : (3) Galvanising Explanation: Galvanization is the process of applying a protective zinc coating to steel or iron, in order to prevent rusting. Although galvanization can be done with electrochemical and ... is hot-dip galvanization, in which steel parts are submerged in a bath of molten zinc.

Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process? (A) Galvanising (B) Tinning (C) Sherardizing (D) None of these

Description : Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process? (A) Galvanising (B) Tinning (C) Sherardizing (D) None of these

Last Answer : (C) Sherardizing

Describe the tinning process. Write its two applications.

Description : Describe the tinning process. Write its two applications.

Last Answer : Tinning: -The process of covering iron or steel sheets with a thin coat of tin to prevent it from rusting is called as tinning.   Process: i) The sheet of steel to be ... Tinned copper sheets are used for cooking utensils and refrigeration equipment. Cu tubes are used in refrigeration. 

The coating of a thin layer of zinc on steel or iron objects is known as (1) Hot dipping (2) Tinning (3) Galvanising (4) Electroplating

Description : The coating of a thin layer of zinc on steel or iron objects is known as (1) Hot dipping (2) Tinning (3) Galvanising (4) Electroplating

Last Answer : Galvanising

Distinguish between Galvanizing and tinning.

Description : Distinguish between Galvanizing and tinning. 

Last Answer : Galvanizing Tinning A process of covering iron or steel with a thin coat of Zinc to prevent it from rusting. A process of covering iron or steel with a thin coat of Tin to ... food stuff since Tin is nontoxic and protects the metal from corrosion and does not causes food poisoning.

Does building a guitar involve any soldering?

Description : Does building a guitar involve any soldering?

Last Answer : Depends on the guitar. Acoustic, no. Electric, yes.

Anyone with soldering experience: Can you help me fix my thumb drive?

Description : Anyone with soldering experience: Can you help me fix my thumb drive?

Last Answer : Sounds like the wires are soldered onto the wrong pins and if ya don’t think any wires or leads are touching you better check it all over so that you do know that they are none touching…

What is soldering ?

Description : What is soldering ?

Last Answer : : After mechanical connection between the wire and the cable conductor, the joint is strengthened by solder and resin to strengthen the joint, increase the durability of the joint and the current barrier is called alloy or soldering.

What is soldering ?

Description : What is soldering ?

Last Answer : Soldering is the process by which two or more metals are joined together.

Why is soldering done ?

Description : Why is soldering done ?

Last Answer : Soldering is done to increase the strength and durability of electrical wiring joints and to ensure uninterrupted wiring and protection from corrosive processes due to unforeseen nature.

What is the ratio of soldering tin lead ?

Description : What is the ratio of soldering tin lead ?

Last Answer : The ratio of lead to tin is 40 ঃ 60.

What is soldering ?

Description : What is soldering ?

Last Answer : : Soldering is a special process by which two or more metallic components are joined together to form a connection and a filler metal element is used as an auxiliary for this purpose which is formed by flow at the junction in molten state.

looking for: soldering irons Prague

Description : Hello, I'm looking for someone who can solder, I need to solder up to 3.5 mm Jack cable, thank you

Last Answer : Almost anyone can do it, if possible. or anyone doing something in electronics

What is the type of solder that would be used in hard soldering?

Description : What is the type of solder that would be used in hard soldering?

Last Answer : Need answer

Why do you think it is best for a soldering iron to have a soldering stand?

Description : Why do you think it is best for a soldering iron to have a soldering stand?

Last Answer : Have you ever had a soldering iron roll off the table and landon your wrist, burning a hole that took over a month to heal? I didin 5th grade while building one of the Radio Shack electronics kitsI had ... stand!!! I was nevergoing to run the risk of a soldering iron getting away from meagain!!!!!

Why do you think it is best for a soldering iron to have a soldering stand?

Description : Why do you think it is best for a soldering iron to have a soldering stand?

Last Answer : Have you ever had a soldering iron roll off the table and landon your wrist, burning a hole that took over a month to heal? I didin 5th grade while building one of the Radio Shack electronics kitsI had ... stand!!! I was nevergoing to run the risk of a soldering iron getting away from meagain!!!!!

Acid soldering flux poisoning?

Description : Acid soldering flux poisoning?

Last Answer : DefinitionAcid soldering flux is a chemical used to clean and protect the area (joint) where two pieces of metal come together. Flux poisoning occurs when someone swallows this substance.This is for information only ... Network.Also reviewed by David Zieve, MD, MHA, Medical Director, A.D.A.M., Inc.

Where can I go to get some information on soldering iron?

Description : Where can I go to get some information on soldering iron?

Last Answer : When you use a soldering iron you would be soldering some kind of metal frame or something because soldering irons are irrelevant to soldering iron. Sorry, not applicable.

What is soldering iron and how do you use it?

Description : What is soldering iron and how do you use it?

Last Answer : Soldering iron is used in heating the metal for soldering. If you want to learn more about soldering iron visit en.wikipedia.org/wiki/Soldering_iron.

Soldering Station?

Description : Soldering Station?

Last Answer : The key to getting a good soldering station is first knowing what purpose you are going to be using it for. After that, make sure the one you choose is sturdy enough, and has enough room for what you are doing. Avoid cheaply made stations as they are prone to defects.

Soldering of two metals is possible because of the property of – (1) Viscosity (2) Osmosis (3) Cohesion (4) Surface tension

Description : Soldering of two metals is possible because of the property of – (1) Viscosity (2) Osmosis (3) Cohesion (4) Surface tension

Last Answer : (3) Cohesion Explanation: Soldering is the process of joining two metals by the use of a solder alloy, and it is one of the oldest known joining techniques. It is possible because of the ... through-out the interior of substance. Soldering leads to alloy formation at the layer between two metals.

Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Description : Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Last Answer : Answer: B

When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an oven to an even temperature and recheck with an ohmmeter B. reheat the connection with a match and recheck with an ohmmeter C. reheat connection with a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Description : When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an ... a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Last Answer : Answer: C

When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Description : When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Last Answer : Answer: B

Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded to the board may come loosened from the board. C. The circuit board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Last Answer : Answer: B

If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at a time B. using a thermal shunt C. pre-oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Description : If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at ... oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Last Answer : Answer: B

Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Last Answer : Answer: D

The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps the turn before it C. apply the tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Description : The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps ... tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Last Answer : Answer: B

Soldering of two metals is possible due to the property–

Description : Soldering of two metals is possible due to the property–

Last Answer : Cohesion

What is soldering and what is brazing?

Description : What is soldering and what is brazing?

Last Answer : Soldering is the process of joining two metals with an alloy whose melting point is less that of the materials to be soldered. Soldering at high temperature using brass as solder is called brazing or hard ... soft solder) is tin 60% and lead 40%. Its melting point is 190°C and is widely used.  

Glass pipes can be joined by (A) Flanges (B) Welding (C) Soldering (D) Bell and spigot joint

Description : Glass pipes can be joined by (A) Flanges (B) Welding (C) Soldering (D) Bell and spigot joint

Last Answer : (D) Bell and spigot joint