Why is steel wool NEVER used as an abrasive to clean soldering tools?

Why is steel wool NEVER used as an abrasive to clean  soldering tools?
by

1 Answer

Answer :

The strands can fall into electrical equipment being worked on  and cause short circuits.
by

Related questions

What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Description : What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Last Answer : The soldering tips are hot only during the brief period of soldering the connection, thus minimizing the chance of burning the wire insulation or connector inserts.

A soldering gun should NOT be used on what components?

Description : A soldering gun should NOT be used on what components?

Last Answer : Electronic components, such as resistors, capacitors, and transistors.

Why are solvents used in the soldering process?

Description : Why are solvents used in the soldering process?

Last Answer : To remove contaminants from soldered connections.

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

What purpose does flux serve in the soldering process?

Description : What purpose does flux serve in the soldering process?

Last Answer : It cleans the metal by removing the oxide layer and prevents further oxidation during the soldering

What causes the nuts or screws that hold the tips on soldering irons and guns to loosen?

Description : What causes the nuts or screws that hold the tips on soldering irons and guns to loosen?

Last Answer : The heating and cooling cycles.

What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Description : What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Last Answer : It will overheat and could burn the insulation of the wire being soldered.

What should be done to a soldering iron tip that is pitted?

Description : What should be done to a soldering iron tip that is pitted?

Last Answer : File the tip until it is smooth and retin it.

State why a well-designed soldering iron is self-regulating

Description : State why a well-designed soldering iron is self-regulating

Last Answer : The resistance of its heating element increases with rising temperature, thus limiting the current flow.

Why are small-wattage soldering irons not used to solder large conductors?

Description : Why are small-wattage soldering irons not used to solder large conductors?

Last Answer : Although its temperature is as high as the larger irons, it does not have thermal inertia.

What does "tinning" mean in relationship to soldering?

Description : What does "tinning" mean in relationship to soldering?

Last Answer : The coating of the material to be soldered with a light coat of solder.

Why must items to be soldered be cleaned just prior to the soldering process?

Description : Why must items to be soldered be cleaned just prior to the soldering process?

Last Answer : Solder will not adhere to dirty, greasy, or oxidized surfaces.

How should excess solder be removed from a hot soldering iron?

Description : How should excess solder be removed from a hot soldering iron?

Last Answer : By use of a cleaning cloth.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

Flux aids in soldering by removing what from surfaces to be soldered?

Description : Flux aids in soldering by removing what from surfaces to be soldered?

Last Answer : Oxides.

In soldering, what alloy changes directly from a solid state to a liquid state?

Description : In soldering, what alloy changes directly from a solid state to a liquid state?

Last Answer : Eutectic.

How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Last Answer : Use a skipping pattern

What determines the shape and size of a soldering iron tip?

Description : What determines the shape and size of a soldering iron tip?

Last Answer : The type of work to be done.

What is the most common source of heat in electronic soldering?

Description : What is the most common source of heat in electronic soldering?

Last Answer : Conductive-type soldering iron.

The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Description : The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Last Answer : Option C

I have wool blanket that is dry clean only - but it's shedding like crazy! What are my options?

Description : I have wool blanket that is dry clean only - but it's shedding like crazy! What are my options?

Last Answer : Dry clean it. Washing it will shrink i really badly.

how do you clean wool that's just been shorn?

Description : how do you clean wool that's just been shorn?

Last Answer : you have to card it to get out the big pieces. that involves these two sorta' blocks with hooks all over 'em, and you pass the wool back and forth between them. this combs the filth out. i wouldn't put any liquid on it at all until you've cleaned it like this.

How To Clean Wool Oriental Rugs?

Description : How To Clean Wool Oriental Rugs?

Last Answer : Prevention is always key in maintaining a wool oriental rug.However accidents do happen and there are chances that the rugmight be dirtied or stained. This does not mean that the rug isruined or destroyed. A ... to be cleaned.If a person doesn't want to or have the time to clean their wooloriental

How To Clean Wool Braided Rugs?

Description : How To Clean Wool Braided Rugs?

Last Answer : A nice accent to a home or an apartment is a wool braided rug.These rugs are beautifully braided together usually in a roundshape with a variety of different colors. This type of decor willadd any personality ... vacuum bag beempty for this step. If a person does not own a vacuum they canhang it f

What is the best way to clean wool carpeting?

Description : What is the best way to clean wool carpeting?

Last Answer : I have a wool carpet. How is wool carpet cleaning done?

Which is best used as a sound absorbing material in partition walls? (1) Stone chips (2) Steel (3) Glass – wool (4) Glass pieces

Description : Which is best used as a sound absorbing material in partition walls? (1) Stone chips (2) Steel (3) Glass – wool (4) Glass pieces

Last Answer : (3) Glass – wool Explanation: Materials that do not transfer mechanical energy well. These tend to be soft, flexible, low density, and with high surface area to linear area ratios.

Which is best used as a sound absorbing material in partition walls? (1) Stone chips (2) Steel (3) Glass - wool (4) Glass pieces

Description : Which is best used as a sound absorbing material in partition walls? (1) Stone chips (2) Steel (3) Glass - wool (4) Glass pieces

Last Answer : (3) Glass - wool Explanation: Materials that do not transfer mechanical energy well. These tend to be soft, flexible, low density, and with high surface area to linear area ratios.

Modern Society question: Do you feel that being rude, abrasive, sarcastic, or apathetic are the new norms for acceptable behavior and ettiquette?

Description : Modern Society question: Do you feel that being rude, abrasive, sarcastic, or apathetic are the new norms for acceptable behavior and ettiquette?

Last Answer : There has always been rude, abrasive, sarcastic, or apathetic people. I would start with the need of a two paycheck household. A child gets better direction when a parent is home to guide them.

Abrasive exhaust - corrosion

Description : When crossing the curb, I probably stuck in the underside of the car and during the visual inspection I noticed that the exhaust cabin is slightly frayed. On another forum, I learned that the anti- ... given place? Or would the exhaust cell start to corrode? Thank you for your answers and responses.

Last Answer : I wouldn't deal with it personally. Corrosion will sooner or later burn the exhaust and you will change it. Even if it is scratched, it will not significantly reduce the service life of the exhaust.

Trinitrotoluene is – (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive

Description : Trinitrotoluene is – (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive

Last Answer : (4) used as an explosive Explanation: Trinitrotoluene (C6H2 (NO2)3.CH3), abbreviated as TNT, is sometimes used as a reagent in chemical synthesis, but it is best known as an explosive material ... The explosive yield of TNT is considered to be the standard mea-sure of bombs and other explosives.

The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength of the insulation B. the paint dust is composed of abrasive and semi-conducting materials which impair insulation C. paint dust buildup has a tendency to cause corrosion D. phase windings frequently become isolated from each other due to dust interference at the terminals

Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals

Last Answer : Answer: B

All of the following items can be used in the maintenance of a D.C. propulsion motor's commutator EXCEPT _______________. A. a canvas wiper B. safety solvent C. abrasive dressing stones D. sandpaper

Description : All of the following items can be used in the maintenance of a D.C. propulsion motor's commutator EXCEPT _______________. A. a canvas wiper B. safety solvent C. abrasive dressing stones D. sandpaper

Last Answer : Answer: B

Epoxy resin is (A) Not used for surface coating (B) A good abrasive (C) An elastomer (D) A polyester

Description : Epoxy resin is (A) Not used for surface coating (B) A good abrasive (C) An elastomer (D) A polyester

Last Answer : (B) A good abrasive

Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Description : Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Last Answer : (A) Apron

__________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Last Answer : (B) Belt

Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Description : Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Last Answer : (C) Flight conveyor

Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Description : Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Last Answer : (B) Suitable for sticky materials

Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Description : Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Last Answer : (B) Large quantity of very fine

Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Description : Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Last Answer : (A) Attrition

__________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Description : __________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Last Answer : (A) Flight

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

Cermets are __________ materials. (A) Refractory (B) Reinforced (C) Abrasive (D) Fully metallic

Description : Cermets are __________ materials. (A) Refractory (B) Reinforced (C) Abrasive (D) Fully metallic

Last Answer : (A) Refractory

The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (A) Abrasive

Give reason Why Diamond is used as abrasive?

Description : Give reason Why Diamond is used as abrasive?

Last Answer : Ans. because it is the hardest substance . All the four valencies are filled.

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (A) Embeddability

Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Last Answer : b) Corrosive

What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Description : What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Last Answer : a) Adhesive wear

Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Description : Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Last Answer : (B) Abrasive