What condition gives maximum power transfer from the source to the load?

What condition gives maximum power transfer from the  source to the load?
by

1 Answer

Answer :

When the load resistance equals the source resistance.
by

Related questions

In order to get maximum power transfer from a capacitive source, the load must?

Description : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

Last Answer : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

Which connector should you use to connect the (a) power source and (b) load to the fuseholder shown in figure 2-12(A)?

Description : Which connector should you use to connect the (a) power source and (b) load to the fuseholder shown in figure 2-12(A)?

Last Answer : a. Center connector b. Outside connector

What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Last Answer : Equal impedance.

If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?

Description : If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?

Last Answer : The ground (reference point) is placed in the proper point in the voltage divider so that positive and negative voltages are supplied

what part of the circuit is the (a) load and (b) source?

Description : what part of the circuit is the (a) load and (b) source?

Last Answer : a) DS1, the flashlight bulb (b) BAT, the dry cell

A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Description : A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Last Answer : C. Load water

Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Description : Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Last Answer : D. transfer maximum power to the load

When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W

Description : When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W

Last Answer : Ans: 0W

What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Description : What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Last Answer : a. Size of the headgap. b. Speed of the magnetic tape.

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source

Description : For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: A) twice the load impedance B) complex conjugate of load impedance C) twice the complex conjugate of load impedance D) none of these 

Last Answer :  For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: complex conjugate of load impedance

For maximum transfer of power, internal resistance of the source should be?

Description : For maximum transfer of power, internal resistance of the source should be?

Last Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Description : What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Last Answer : An unbalance in the metering bridge.

When a source is delivering maximum power to a load, the efficiency of the circuit is always

Description : When a source is delivering maximum power to a load, the efficiency of the circuit is always (a) 50% (b) 75% (c) 100% (d) Depends on the circuit parameters

Last Answer : When a source is delivering maximum power to a load, the efficiency of the circuit is always 50%

What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Description : What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Last Answer : 200 psig.

A distillation column with N plates is being operated under normal conditions. At some point of time, the operation is shifted to total reflux condition (i.e., no product and residue are being withdrawn and feed to the column is stopped). At the new steady state, (A) Composition of vapors and that of liquid do not vary throughout the column (B) Reboiler load and condenser load are minimum (C) The top and bottom compositions are unchanged with and without total reflux (D) The top and bottom compositions correspond to the maximum enrichment available

Description : A distillation column with N plates is being operated under normal conditions. At some point of time, the operation is shifted to total reflux condition (i.e., no product and residue are ... and without total reflux (D) The top and bottom compositions correspond to the maximum enrichment available

Last Answer : (D) The top and bottom compositions correspond to the maximum enrichment available

What is the efficiency of power transfer in question 30?

Description : What is the efficiency of power transfer in question 30?

Last Answer : 50 percent.

If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Description : If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Last Answer : 33.33%

What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Description : What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Last Answer : Shorting probe.

What device is used to switch power from the normal source to an alternate source for nonvital users?

Description : What device is used to switch power from the normal source to an alternate source for nonvital users?

Last Answer : What device is used to switch power from the normal source to an alternate source for nonvital users?

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

Power for the electronic digital multimeter is normally supplied by what internal power source?

Description : Power for the electronic digital multimeter is normally supplied by what internal power source?

Last Answer : Rechargeable batteries.

What factors should be considered when selecting a primary cell for a power source?

Description : What factors should be considered when selecting a primary cell for a power source?

Last Answer : Cost, size, ease of replacement, and voltage or current needs. b. Capacitance is the property of a circuit which opposes changes in voltage.

What factors should be considered when selecting a primary cell for a power source?

Description : What factors should be considered when selecting a primary cell for a power source?

Last Answer : Cost, size, ease of replacement, and voltage or current needs. b. Capacitance is the property of a circuit which opposes changes in voltage.

The presence of ozone due to corona is harmful because it (a) reduces power factor (b) corrodes the material (c) gives odour (d) transfer energy to the ground (e) none of the above

Description : The presence of ozone due to corona is harmful because it (a) reduces power factor (b) corrodes the material (c) gives odour (d) transfer energy to the ground (e) none of the above

Last Answer : (b) corrodes the material

. What primary condition must magnetic lines of force meet in order to exist?

Description : . What primary condition must magnetic lines of force meet in order to exist?

Last Answer : Magnetic lines of force must form a continuous closed loop.

What is the condition of the diode in a series limiter when an output is developed? In a parallel limiter?

Description : What is the condition of the diode in a series limiter when an output is developed? In a parallel limiter?

Last Answer : Conducting, cutoff.

In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Last Answer : Nonresonant (circuit is either above or below resonance)

What causes the specified condition to shift position?

Description : What causes the specified condition to shift position?

Last Answer : The input, or clock pulse.

What condition must occur to have a change in the output of a D FF?

Description : What condition must occur to have a change in the output of a D FF?

Last Answer : A positive-going clock pulse.

A tape pack has gaps in the tape winding as shown in figure 2-5. What causes this condition?

Description : A tape pack has gaps in the tape winding as shown in figure 2-5. What causes this condition?

Last Answer : Tape is loosely wound on reel.

A tape pack is buckled and deformed as shown in figure 2- 4. What are three possible causes for this condition?

Description : A tape pack is buckled and deformed as shown in figure 2- 4. What are three possible causes for this condition?

Last Answer : a. Reel has a distorted hub, b. tape wound over small particle deposited on hub, and c. tape wound on reel with tension increasing toward end of winding.

. After rewinding a tape onto its supply reel, you examine the tape pack and notice pile-ups of tape resembling the example in figure 2-2. What causes this condition?

Description : . After rewinding a tape onto its supply reel, you examine the tape pack and notice pile-ups of tape resembling the example in figure 2-2. What causes this condition?

Last Answer : The tape is stopped too quickly when winding or rewinding.

For a circuit to be considered to be in the quiescent condition, what

Description : For a circuit to be considered to be in the quiescent condition, what

Last Answer : The input signal

What two properties of the launch condition may affect multimode fiber attenuation measurements?

Description : What two properties of the launch condition may affect multimode fiber attenuation measurements?

Last Answer : . Launch spot size and angular distribution.

Modes of a light pulse that enter the fiber at one time exit the fiber at different times. This condition causes the light pulse to spread. What is this condition called?

Description : Modes of a light pulse that enter the fiber at one time exit the fiber at different times. This condition causes the light pulse to spread. What is this condition called?

Last Answer : Modal dispersion.

What condition causes a light ray to be totally reflected back into its medium of propagation?

Description : What condition causes a light ray to be totally reflected back into its medium of propagation?

Last Answer : Total internal reflection occurs when the angle of refraction approaches 90 degrees. This condition occurs when the angle of incidence increases to the point where no refraction is possible.

What condition must exist on both the limiter and quadrature grids for current to flow in a gated-beam detector?

Description : What condition must exist on both the limiter and quadrature grids for current to flow in a gated-beam detector?

Last Answer : Both grids must be positively biased

What is the most accurate method of determining the condition of an electron tube?

Description : What is the most accurate method of determining the condition of an electron tube?

Last Answer : Testing the tube in its circuit

Prior to substituting a diode, what measurements should you take to determine its condition?

Description : Prior to substituting a diode, what measurements should you take to determine its condition?

Last Answer : Voltages and resistances.

How is an overload condition indicated by the electronic digital multimeter?

Description : How is an overload condition indicated by the electronic digital multimeter?

Last Answer : Simultaneous flashing of display readouts

Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Description : Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Last Answer : De-energized

What is an excessive heat condition?

Description : What is an excessive heat condition?

Last Answer : A condition in which the heat in or around the circuit increases to a higher than normal level

What is an excessive current condition?

Description : What is an excessive current condition?

Last Answer : A condition that is not a direct short but in which circuit current increases beyond the designed current carrying ability of the circuit.

When all the lead sulfate has been converted, what is the condition of the cell?

Description : When all the lead sulfate has been converted, what is the condition of the cell?

Last Answer : Fully charged.

When all the lead sulfate has been converted, what is the condition of the cell?

Description : When all the lead sulfate has been converted, what is the condition of the cell?

Last Answer : Fully charged.

What condition exists when the insertion of a meter into a circuit changes the operation of the circuit?

Description : What condition exists when the insertion of a meter into a circuit changes the operation of the circuit?

Last Answer : Meter-loading.

Determine the correctness or otherwise of the following Assertion [a] and the Reason [r]. Assertion: Fast decoupled load flow method gives approximate load flow solution because it uses several assumptions. Reason: Accuracy depends on the power mismatch vector tolerance. a) Both [a] and [r] are true and [r] is the correct reason for [a]. b) Both [a] and [r] are true and [r] is not the correct reason for [a]. c) [a] is false and [r] is true.

Description : Determine the correctness or otherwise of the following Assertion [a] and the Reason [r]. Assertion: Fast decoupled load flow method gives approximate load flow solution because it uses several assumptions. Reason: Accuracy ... the correct reason for [a]. c) [a] is false and [r] is true.

Last Answer : c) [a] is false and [r] is true

The Preamble is useful in constitutional interpretation because it - (1) uses value loaded words (2) contains the real objective and philosophy of the constitution makers (3) is a source of power and limitation (4) gives and exhaustive list of basic features of the Constitution

Description : The Preamble is useful in constitutional interpretation because it - (1) uses value loaded words (2) contains the real objective and philosophy of the constitution makers (3) is a source of power and limitation (4) gives and exhaustive list of basic features of the Constitution

Last Answer : (2) contains the real objective and philosophy of the constitution makers Explanation: The preamble is useful in constitutional interpretation because it contains the real objective and philosophy of the constitution makers.

When a wave is reflected from a surface, energy is transferred. When is the transfer of energy greatest?

Description : When a wave is reflected from a surface, energy is transferred. When is the transfer of energy greatest?

Last Answer : When the incident wave is nearly parallel with the surface.