What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

What is the height of the base lift (kicker lift) on a typical tube and coupler  scaffold?
a. 225mm (9 inches)
b. 300mm (12 inches)
c. 150mm (6 inches)
d. 100mm (4 inches)
by

1 Answer

Answer :

c. 150mm (6 inches
by

Related questions

What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Description : What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Last Answer : b. 300mm (12 inches)

The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Description : The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Last Answer : c. 150mm (6 inches)

Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Description : Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Last Answer : b. 2/3 of the total threaded length showing

The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Description : The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Last Answer : d. 25mm (1 inch)

What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Description : What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Last Answer : a. 300mm (12 inches)

A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Description : A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Last Answer : b. 360mm (14 inches)

The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Description : The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Last Answer : a. 3 planks 675mm (27 inches)

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Description : What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Last Answer : b. Three

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Description : At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Last Answer : c. Between 95 cm (38 inches) and 115 cm ( 45 inches)

What maximum load would you place on a right angle coupler?

Description : What maximum load would you place on a right angle coupler?

Last Answer : 630kg (or 630kgf or 6.25kN)

What is the maximum load you would lift with a gin wheel?

Description : What is the maximum load you would lift with a gin wheel?

Last Answer : 50kg

The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Description : The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Last Answer : (a) 100mm, 200mm, 300mm

What is the maximum height allowed between ladder landings?

Description : What is the maximum height allowed between ladder landings?

Last Answer : 6m (or 3 lifts)

What is the minimum height an access ladder must extend above the landing?

Description : What is the minimum height an access ladder must extend above the landing?

Last Answer : 1m

Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Description : Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Last Answer : c. Every Fifth post

For A Class, the gross clearance of over maximum moving dimension for BG is (a) 100mm (b) 125mm (c) 150mm* (d) 175mm

Description : For A Class, the gross clearance of over maximum moving dimension for BG is (a) 100mm (b) 125mm (c) 150mm* (d) 175mm

Last Answer : (c) 150mm*

The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Description : The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Last Answer : c. 15m

The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Description : The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Last Answer : b. 6mm ( ¼ inch)

The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Description : The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Last Answer : a. 8m (26 feet)

hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Description : hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Last Answer : b. No more than 9m (30 feet)

Planks must be overlapped a minimum of ------

Description : Planks must be overlapped a minimum of ------

Last Answer : 12 inches.

The headroom above a working platform must be at least? a. 1.6m b. 2.1m c. 2m d. 2.6m

Description : The headroom above a working platform must be at least? a. 1.6m b. 2.1m c. 2m d. 2.6m

Last Answer : c. 2m

At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Description : At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Last Answer : a. 35-55 degree

What minimum width of timber would you use as a soleplate?

Description : What minimum width of timber would you use as a soleplate?

Last Answer : 220mm (or 225mm, or the width of a scaffold plank)

What is the minimum size of a square baseplate?

Description : What is the minimum size of a square baseplate?

Last Answer : 150mm x 150mm (or 225cm2)

Recommended matrix height in citrus is a. 4 inches b. 6 inches c. 9 inches d. 12 inches

Description : Recommended matrix height in citrus is a. 4 inches b. 6 inches c. 9 inches d. 12 inches

Last Answer : 9 inches

Which is better? (1) Kicker L5 15" subwoofer or (2) Kicker L5 12"?

Description : Which is better? (1) Kicker L5 15" subwoofer or (2) Kicker L5 12"?

Last Answer : I’d take 2 12’s over one 15 any day. It really depends what you’re looking for. The 15 will be just plain loud, but two 12’s will most likely give you clearer, more punchy bass. Hope this helps!

What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Description : What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Last Answer : (b) 455mm

Water rises in a capillary tube to a height h. It will rise to a height more than h. a.in a lift moving up with an acceleration b.in all the above cases c.107 dynes d.at the poles e.on the surface of moon

Description : Water rises in a capillary tube to a height h. It will rise to a height more than h. a.in a lift moving up with an acceleration b.in all the above cases c.107 dynes d.at the poles e.on the surface of moon

Last Answer : e. on the surface of moon

What is 6 feet 12 inches height mean?

Description : What is 6 feet 12 inches height mean?

Last Answer : Need answer

What is the area of a triangle that has a base of 10 inches and a height of 7 inches?

Description : What is the area of a triangle that has a base of 10 inches and a height of 7 inches?

Last Answer : The area of triangle is : 35.0

Apline Type-R or Kicker Solobaric L7?

Description : Apline Type-R or Kicker Solobaric L7?

Last Answer : When Kickers are pumping, they are literally heart stopping. I sat in a room with ONE solobaric hooked up to a 1000 watt monoblock amp, and I couldn’t breathe it was so loud and intense.

I just saw a football highlight from 1989 and the place kicker luis zendjas was smoking a cigarette on the sideline during the game has anyone else ever witnessed a professional athlete doing this?

Description : I just saw a football highlight from 1989 and the place kicker luis zendjas was smoking a cigarette on the sideline during the game has anyone else ever witnessed a professional athlete doing this?

Last Answer : Not since about 15–20 years ago.

What is the peak power of the Kicker 08DS12L72?

Description : What is the peak power of the Kicker 08DS12L72?

Last Answer : The peak power of the Kicker 08DS12L72 is 1500 Watts.

Which is better kicker or pyle subwoofer?

Description : Which is better kicker or pyle subwoofer?

Last Answer : Kicker is a much better quality subwoofer than Pyle, and it will have much better bass as well.

Barometric pressure is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) 100mm Hg.

Description : Barometric pressure is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) 100mm Hg.

Last Answer : Answer : a

The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Description : The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Last Answer : a) 250 x 150mm*.

For A class ODC, the gross clearance over maximum moving dimension of B.G is (a) 150mm (b) 175mm (c) 225 mm* (d) (d) 250mm

Description : For A class ODC, the gross clearance over maximum moving dimension of B.G is (a) 150mm (b) 175mm (c) 225 mm* (d) (d) 250mm

Last Answer : (c) 225 mm*

how often to water red-leaf crotons of about 12-inches in height

Description : how often to water red-leaf crotons of about 12-inches in height

Last Answer : If the leaves are droopy then water them more! They're pretty drought tolerant once established but until then you should water them every day that they don't get a good dose of natural rainfall.

What is the surface area of a right triangular prism with a length of 9 inches and a triangular base measuring 3 inches by 4 inches by 5 inches.?

Description : What is the surface area of a right triangular prism with a length of 9 inches and a triangular base measuring 3 inches by 4 inches by 5 inches.?

Last Answer : Surface area: (2*0.5*3*4)+(3*9)+(4*9)+(5*9) = 120 squareinches

Photographers: Can you tell me what difference between a 75-300mm and 55-250mm lens for Canon?

Description : Photographers: Can you tell me what difference between a 75-300mm and 55-250mm lens for Canon?

Last Answer : answer:55-250 will give you a wider angle and less telephoto. 75-300 will give you greater telephoto and less wide angle. The lower the first number, the wider the field of ... -Guide-Chris-Gatcum/dp/1465408452/ref=sr_1_1?s=books&ie=UTF8&qid=1401375024&sr=1-1&keywords=beginners+guide+to+photography

Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Description : Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Last Answer : i’d go for the 55–200 but i was never a big fan of telephoto. still, i think the versatility and price clinch it.

How many 300mm circles in a sq metre?

Description : How many 300mm circles in a sq metre?

Last Answer : Assuming the 300 mm refers to the diameter, there are 9.

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm