What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

What is the maximum distance that bracing can be installed from a node point on  a scaffold?
a. 200mm (8 inches)
b. 300mm (12 inches)
c. 150mm (6 inches)
d. 250mm (10 inches)
by

1 Answer

Answer :

b. 300mm (12 inches)
by

Related questions

What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Description : What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Last Answer : c. 150mm (6 inches

The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Description : The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Last Answer : c. 150mm (6 inches)

Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Description : Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Last Answer : b. 2/3 of the total threaded length showing

What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Description : What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Last Answer : b. Three

What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Description : What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Last Answer : a. 300mm (12 inches)

The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Description : The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Last Answer : d. 25mm (1 inch)

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Description : A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Last Answer : b. 360mm (14 inches)

Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Description : Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Last Answer : c. Every Fifth post

At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Description : At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Last Answer : a. 35-55 degree

The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Description : The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Last Answer : a. 3 planks 675mm (27 inches)

For A class ODC, the gross clearance over maximum moving dimension of B.G is (a) 150mm (b) 175mm (c) 225 mm* (d) (d) 250mm

Description : For A class ODC, the gross clearance over maximum moving dimension of B.G is (a) 150mm (b) 175mm (c) 225 mm* (d) (d) 250mm

Last Answer : (c) 225 mm*

At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Description : At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Last Answer : c. Between 95 cm (38 inches) and 115 cm ( 45 inches)

The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Description : The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Last Answer : c. 15m

The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Description : The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Last Answer : b. 6mm ( ¼ inch)

Tamron 18-270mm vs Canon 18-200mm vs Canon 18-135mm vs Canon 18-55mm+Canon 55-250mm --Which should I get?

Description : Tamron 18-270mm vs Canon 18-200mm vs Canon 18-135mm vs Canon 18-55mm+Canon 55-250mm --Which should I get?

Last Answer : answer:270 needs more light. As does the 250. IE Slower shutter speed and/or larger aperture.

Photographers: Can you tell me what difference between a 75-300mm and 55-250mm lens for Canon?

Description : Photographers: Can you tell me what difference between a 75-300mm and 55-250mm lens for Canon?

Last Answer : answer:55-250 will give you a wider angle and less telephoto. 75-300 will give you greater telephoto and less wide angle. The lower the first number, the wider the field of ... -Guide-Chris-Gatcum/dp/1465408452/ref=sr_1_1?s=books&ie=UTF8&qid=1401375024&sr=1-1&keywords=beginners+guide+to+photography

The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Description : The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Last Answer : a) 250 x 150mm*.

Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Description : Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Last Answer : i’d go for the 55–200 but i was never a big fan of telephoto. still, i think the versatility and price clinch it.

The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Description : The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Last Answer : (a) 100mm, 200mm, 300mm

What is the maximum height allowed between ladder landings?

Description : What is the maximum height allowed between ladder landings?

Last Answer : 6m (or 3 lifts)

What maximum load would you place on a right angle coupler?

Description : What maximum load would you place on a right angle coupler?

Last Answer : 630kg (or 630kgf or 6.25kN)

What is the maximum load you would lift with a gin wheel?

Description : What is the maximum load you would lift with a gin wheel?

Last Answer : 50kg

The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Description : The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Last Answer : a. 8m (26 feet)

hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Description : hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Last Answer : b. No more than 9m (30 feet)

Planks must be overlapped a minimum of ------

Description : Planks must be overlapped a minimum of ------

Last Answer : 12 inches.

The headroom above a working platform must be at least? a. 1.6m b. 2.1m c. 2m d. 2.6m

Description : The headroom above a working platform must be at least? a. 1.6m b. 2.1m c. 2m d. 2.6m

Last Answer : c. 2m

What is the minimum height an access ladder must extend above the landing?

Description : What is the minimum height an access ladder must extend above the landing?

Last Answer : 1m

What minimum width of timber would you use as a soleplate?

Description : What minimum width of timber would you use as a soleplate?

Last Answer : 220mm (or 225mm, or the width of a scaffold plank)

What is the minimum size of a square baseplate?

Description : What is the minimum size of a square baseplate?

Last Answer : 150mm x 150mm (or 225cm2)

To assess the surface of a weld for direct inspection, the distance from the surface to eye should be a maximum of? a) 200mm b) 600mm c) 60mm d) 6000mm

Description : To assess the surface of a weld for direct inspection, the distance from the surface to eye should be a maximum of? a) 200mm b) 600mm c) 60mm d) 6000mm

Last Answer : b) 600mm

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

Which distance is larger 250mm or 2cm?

Description : Which distance is larger 250mm or 2cm?

Last Answer : 250mm is 25cm, which is larger than 2cm.

The inverse Square Law is concerned with intensity of radiation using type D film of 200mm target to film distance, the exposure time was 0.25s. What would be the exposure for the same situation with 400mm target to film distance? M07********** A. 0.5s B. 1.0s C. 2.0s D. 0.25s E. 0.125s

Description : The inverse Square Law is concerned with intensity of radiation using type D film of 200mm target to film distance, the exposure time was 0.25s. What would be the exposure for the same situation with 400mm target to film distance? M07********** A. 0.5s B. 1.0s C. 2.0s D. 0.25s E. 0.125s

Last Answer : B. 1.0s

For A Class, the gross clearance of over maximum moving dimension for BG is (a) 100mm (b) 125mm (c) 150mm* (d) 175mm

Description : For A Class, the gross clearance of over maximum moving dimension for BG is (a) 100mm (b) 125mm (c) 150mm* (d) 175mm

Last Answer : (c) 150mm*

The clear distance between consecutive sleepers laid over unballasted bridge on BG should not exceed a)300mm b)400mm c)450mm* d)550mm

Description : The clear distance between consecutive sleepers laid over unballasted bridge on BG should not exceed a)300mm b)400mm c)450mm* d)550mm

Last Answer : c)450mm*

A wave and its reflection produce a standing wave with the distance from NODE to nearest ANTINODE of 4 meters. The wavelength of this wave is: w) 4 meters x) 8 meters y) 12 meters z) 16 meters

Description : A wave and its reflection produce a standing wave with the distance from NODE to nearest ANTINODE of 4 meters. The wavelength of this wave is: w) 4 meters x) 8 meters y) 12 meters z) 16 meters

Last Answer : ANSWER: Z -- 16 METERS

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Description : What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Last Answer : (b) 455mm

Not far off shore a ship stands with a rope ladder hanging over her side. The rope has 10 rungs. The distance between each rung is 12 inches. The lowest rung touches the water. The ocean is calm. Because of the incoming tide, the surface of the water rises 4 inches per hour. How soon will the water cover the third rung from the top rung of the rope ladder? -Riddles

Description : Not far off shore a ship stands with a rope ladder hanging over her side. The rope has 10 rungs. The distance between each rung is 12 inches. The lowest rung touches the water. The ocean is calm. ... hour. How soon will the water cover the third rung from the top rung of the rope ladder? -Riddles

Last Answer : When a problem deals with a physical phenonmenon, the phenonmenon should be considered as well as the numbers given. As the water rises, so does the rope ladder. The water will never cover the rung.

has amplitude of vibration is 200mm and frequency of operation is 400 cycle/ sec. b. Acme tooth harrow c. Blade harrow d. None of the above

Description : has amplitude of vibration is 200mm and frequency of operation is 400 cycle/ sec. b. Acme tooth harrow c. Blade harrow d. None of the above

Last Answer : Ans- a. Reciprocating power harrow

A standing wave is formed on a tightly stretched string. The distance between a node and an antinode is: w) 1/8 wavelength x) 1/4 wavelength y) 1/2 wavelength z) 1 wavelength

Description : A standing wave is formed on a tightly stretched string. The distance between a node and an antinode is: w) 1/8 wavelength x) 1/4 wavelength y) 1/2 wavelength z) 1 wavelength

Last Answer : ANSWER: X -- 1/4 WAVELENGTH

How many 300mm circles in a sq metre?

Description : How many 300mm circles in a sq metre?

Last Answer : Assuming the 300 mm refers to the diameter, there are 9.

A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Last Answer : A 0.144

A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) It should not be done because the thickness is below that recommended b) It should be better to use a cobalt 60 source in this instance c) There is no problem with the technique d) Only the double wall, double image technique should be used with Iridium

Description : A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) ... problem with the technique d) Only the double wall, double image technique should be used with Iridium

Last Answer : c) There is no problem with the technique

How do you remove a plugin in a Ruby on Rails application and scaffold?

Description : How do you remove a plugin in a Ruby on Rails application and scaffold?

Last Answer : answered my own question I think. script/generate scaffold lfp_contact didn't load the helpers with the right case sensitivity. change the helper method and was able to run script/server. Hopefully I will be ... keep all my cases lowercase. and I won't use underscores in my naming conventions. ^_^

Where can I recieve scaffold safety training?

Description : Where can I recieve scaffold safety training?

Last Answer : If you are going to be working around scaffolding, you have to have safety training. Training programs are written with OSHA specifications, and you can order training CDs. http://www.affordablesafetytraining.com/tsca.html