Draw and explain force or weight measurement using load cell.

Draw and explain force or weight measurement using load cell. 
by

1 Answer

Answer :

image

Description: Load cells utilize an elastic member as the primary transducer and strain gauges as secondary transducers. Strain gauges may be attached to any elastic member, on which there exists a, suitable plane area to accommodate them. This arrangement may then be used to measure loads applied to deform or deflect the elastic member, provided that the resultant strain is large enough to produce detectible outputs. Fig. above shows a column type load cell mounted with four strain gauges on its periphery. The output voltage measured across the four arm Wheatstone bridge circuit, is a measure of the weight being applied.

by

Related questions

Draw and explain the measurement of torque using Torque Cell

Description : Draw and explain the measurement of torque using Torque Cell

Last Answer : Figure a shows the construction of load cell used to measure torque using strain gauges connected to the rotating shaft.. Figure b represents the bridge arrangement to measure torque. .The ... diagonal axis. The Wheatstone bridge output is proportional to torsion and hence the torque. . 

Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Description : Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Last Answer : (i) Measurement of active power in 3- phase load circuit using two- wattmeter: (ii) Measurement of reactive power in 3- phase load circuit using one wattmeter

Draw and explain the circuit diagram for measurement of single phase power using dynamometer type wattmeter.

Description : Draw and explain the circuit diagram for measurement of single phase power using dynamometer type wattmeter. 

Last Answer : Circuit diagram for measurement of single phase power using dynamometer type wattmeter: Explanation: It consists of two stationary coils, called current coils and one moving coil, called voltage or ... i.e. power. The meter can be calibrated directly to indicate the power in watts. 

Draw and explain in brief speed measurement using non-contact type transducer.

Description : Draw and explain in brief speed measurement using non-contact type transducer. 

Last Answer :  i) Photoelectric Tachometer:  This method of measuring speed consists of mounting an opaque disc on the rotating shaft. The disc has a number of equidistant holes on its periphery. At one side of the disc a light source is ... (pulses per second /number of teeth)  = (P/T) rps = (P/T) *60 rpm.

Draw and explain the displacement measurement system using LVDT.

Description : Draw and explain the displacement measurement system using LVDT.

Last Answer : (Or)  LVDT has a single primary winding P and two secondary windings S1 and S2 wound on a cylindrical former. S1 and S2 have equal number of turns and are ... while simultaneously reducing the voltage in the other winding. Output voltage Vo measured is equivalent to the displacement.

Draw and explain temperature measurement using RTD. State its advantages and disadvantages.

Description : Draw and explain temperature measurement using RTD. State its advantages and disadvantages.

Last Answer : https://youtu.be/rYcglFW4y0I

Explain how force is measured using load cell

Description : Explain how force is measured using load cell

Last Answer : Load cell are primarily intended for measurement of weight of bodies such as slowly moving vehicles. Load cell utilize an elastic member as primary transducer and strain gauges as secondary transducer. ... is held vertically by guard plates so as to increase its stiffness in the radial direction.

What is encoder? Draw and explain an optical encoder operation for rotary motion measurement.

Description : What is encoder? Draw and explain an optical encoder operation for rotary motion measurement.

Last Answer : Definition: Digital encoders convert analog motion (rotary or linear) to a digital output form. An optical encoder is an electromechanical device which has an electrical output in digital form proportional to ... . In this way a train of pulses equivalent to the rotation is obtained as shown.

Draw and explain the working principle of ultrasonic level measurement system. Also give advantages, disadvantages and applications of it.

Description : Draw and explain the working principle of ultrasonic level measurement system. Also give advantages, disadvantages and applications of it.

Last Answer : Ultrasonic level detectors operate either by the absorption of acoustic energy as it travels from source to receiver or by the attenuation (frequency change) of a vibrating diaphragm face, oscillating at ... without making physical contact with the process material. 2. They have no moving parts.

Draw a diagram of radar level measurement. Write an advantage and disadvantage of it.

Description : Draw a diagram of radar level measurement. Write an advantage and disadvantage of it.

Last Answer : Advantages:  • This is non contact method  • High accuracy for measurements in storage tanks and process vessels Disadvantages:  • Expensive technology  • Reading is affected by change in density of liquid

State how pressure measurement can be done using Dead weight tester.

Description : State how pressure measurement can be done using Dead weight tester.

Last Answer : The handle is fully drawn out and the oil is allowed to enter in the cylinder (i.e. gauge and piston) The weight to be measured is placed on the platform. Now the handle is turned ... of the area of the piston and the pressure indicated on the gauge is equal to the weight under measurement.

Load cells used for the measurement of weight has (A) Compact & rugged construction with an accuracy of 0.1 to 1% (B) No moving parts and incurs negligible deflection under load (C) Provision of thermal compensation and is hermetically sealed (D) All 'a', 'b' & 'c'

Description : Load cells used for the measurement of weight has (A) Compact & rugged construction with an accuracy of 0.1 to 1% (B) No moving parts and incurs negligible deflection under load (C) Provision of thermal compensation and is hermetically sealed (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.   

Draw and explain Doppler type flow measurement.

Description : Draw and explain Doppler type flow measurement.

Last Answer : Doppler type ultrasonic flow meter ➢ Explianation: The Doppler Effect Ultrasonic Flow meter use reflected ultrasonic waves to measure the fluid velocity. There is a change in ultrasonic ... , there will be a frequency shift at the receiver end which is protentional to the velocity

Draw Bourdon tube with LVDT setup for pressure measurement.

Description : Draw Bourdon tube with LVDT setup for pressure measurement.

Last Answer : Bourdon tube with LVDT setup for pressure measurement.

Draw the experimental setup of plate load test using gravity loading.

Description : Draw the experimental setup of plate load test using gravity loading.

Last Answer : Plate Load Test :- 1.Bearing Plate: - It is either circular or square made up mild steel of not less than 25mm thickness and varying in size from 300 to 750mm with grooved bottom. For clayey soil ... settlement curve is plotted where load intensity is on X axis and Settlement is on Y axis.

Describe with neat labeled diagram measurement of flow using turbine flow meter.

Description : Describe with neat labeled diagram measurement of flow using turbine flow meter.

Last Answer : Explanation: - Turbine flow meter s are volumetric flow meters and are available in wide ranges. The output is usually in the form of a digital electrical signal whose frequency is directly ... totalized by a counter to give the value of total flow over a particular interval of time.

Describe rotary motion measurement using optical encoder.

Description : Describe rotary motion measurement using optical encoder.

Last Answer : An optical encoder is an electromechanical device which has an electrical output in digital form proportional to the angular position of the input shaft. Optical encoders enable an angular ... amplified and converted into digital form. This signal is then transmitted to the data processor.

Describe the instrumentation system used for temperature measurement using thermistor.

Description : Describe the instrumentation system used for temperature measurement using thermistor.

Last Answer : A thermistor is a type of resistor whose resistance is dependent on temperature. Thermistors are of two opposite fundamental types: With NTC, resistance Decreases with temperature to ... converted to Digital by ADC further given to multiplexer, then output is displayed on computer. 

The measurement of dielectric loss and power factor is done using...

Description : The measurement of dielectric loss and power factor is done using  (A) Weins Bridge (B) Hays Bridge (C) Schering Bridge (D) Wheat Stone Bridge 

Last Answer : C Schering brigde

Define magnetic lines of force. Also draw and show magnetic lines of force of a bar type magnet.

Description : Define magnetic lines of force. Also draw and show magnetic lines of force of a bar type magnet.

Last Answer : Magnetic Lines of force- These are the imaginary lines (having no physical existence) introduced by Faraday for the pictorial representation of the distribution of a magnetic field.  OR  A line of ... that the tangent at any point gives direction of the resultant force at that point. 

Draw circuit diagram of Bistable multivibrator using IC-555 and explain its working.

Description : Draw circuit diagram of Bistable multivibrator using IC-555 and explain its working.

Last Answer : Definition – A multivibrator which has two stable states, one can be change to other when trigger pulse is applied, known as bistable multivibrator. Circuit diagram of Bistable multivibrator using IC555

Draw the diagram of zero crossing detector using op-amp and explain its working.

Description : Draw the diagram of zero crossing detector using op-amp and explain its working.

Last Answer : The zero crossing detector circuit is an important application of the op-amp comparator circuit. It can also be called as the sine to square wave converter. Anyone of the inverting or non-inverting ... the possibility of any false zero crossing due to noise voltages at the op-amp input.

In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings

Description :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the ... kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Last Answer :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the ... of current coil. the power factor and reactive power of the load is 0.2 & 6 √3 kVAR

In the case of power measurement by two wattmeter method in a balanced 3Φ system with a pure inductive load

Last Answer : In the case of power measurement by two wattmeter method in a balanced 3Φ system with a pure inductive load both the Wattmeter will indicate the same but of opposite sign.

Draw a centralized SPC organization and explain how it works under load sharing operation.

Description : Draw a centralized SPC organization and explain how it works under load sharing operation.

Last Answer : In centralized control, all the control equipment is replaced by a single processor which must be quite powerful. It must be capable of processing 10 to 100 calls per second, depending on the ... both the processors are active simultaneously and share the load and the resources dynamically.  

Explain plate load test and draw a load settlement curve

Description : Explain plate load test and draw a load settlement curve

Last Answer : i) Plate load test is a filed test to determine the ultimate bearing capacity f soil and probable settlement under given loading. ii) The test essentially consist in loading a rigid plate, called bearing ... /hr xi) the results of test are plotted between settlement and load intensity

All systems of measurement use the same units for which of the following? w) mass x) time y) force z) volume

Description : All systems of measurement use the same units for which of the following? w) mass x) time y) force z) volume

Last Answer : ANSWER: X -- TIME

Explain the working of diaphragm for pressure measurement.

Description : Explain the working of diaphragm for pressure measurement. 

Last Answer : Capacitive transducers are used for the measurement of pressure by converting the pressure into a displacement. The displacement is sensed by a capacitive transducer using a differential arrangement's ... shows a 1800 phase shift. This voltage may be amplified by an emitter follower amplifier.

How strain gauge is used for pressure measurement, explain?

Description : How strain gauge is used for pressure measurement, explain?

Last Answer : strain gauge: - strain gauge is used for pressure measurement as one of the arm of a wheatstones' bridge, the pressure is applied to the strain gauge through diaphragm elastic pressure sensor.

Explain the need of level measurement.

Description : Explain the need of level measurement.

Last Answer : Need of level measurement: In almost all industries, vast quantities of liquids such as water, solvents, chemicals etc. are used in number of processes. Liquid level measurements are widely ... chemical process variability, resulting in higher product quality, reduced cost, and less waste.

With neat diagram, explain working of capacitance level measurement.

Description : With neat diagram, explain working of capacitance level measurement.

Last Answer : working : The capacitive level detector operates on the equation of parallel plate capacitor, i.e. C = ε A/d. It consist of an insulated capacitance probe (which is a metal electrode) ... in the capacitance is measured and is displayed on the indicator calibrated in terms of liquid level. 

Explain significance and purpose of electrical measurement system.

Description : Explain significance and purpose of electrical measurement system.

Last Answer : ➢ Significance of Electrical Measurement System  1. The measurement is required for measurement of all physical quantities for e.g speed, velocity, temperature, pressure etc.  2. All electrical ... 4. These standards and references may changes time to time, area to area person to person 

Explain V- I method of measurement of medium resistance.

Description : Explain V- I method of measurement of medium resistance. 

Last Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

Draw a neat labeled diagram of Automatic Weight Tensioning and Temperature Compensation and give any two advantages of the same.

Description : Draw a neat labeled diagram of Automatic Weight Tensioning and Temperature Compensation and give any two advantages of the same.

Last Answer :  figure of automatic weight tensioning Advantages of automatic weight tensioning and temperature compensation:  Sparkless current collection at higher speeds.  OHE becomes more dynamically ... of unregulated OHE.  Because of fixed tension, fluctuations in the height are minimized

Explain measurement of phase and frequency using Lissajous pattern. Write the formula for each one.

Description : Explain measurement of phase and frequency using Lissajous pattern. Write the formula for each one.

Last Answer : Phase measurement of Lissajous pattern: The phase measurement can be done by using Lissajous figures. The CRO is set to operate in the X- Y mode, then the display obtained on the screen of a ... or sub- multiple of the unknown frequency.  The Lissajous pattern appears stationary.     

Explain the measurement of voltage and frequency using CRO.

Description : Explain the measurement of voltage and frequency using CRO.

Last Answer : Voltage Measurement: CRO displays the voltage signal as a function of time on its screen. The amplitude of that voltage signal is constant, but we can vary the number of divisions that cover the voltage ... /division nv is the number of divisions that cover the signal in vertical direction.

Explain in brief linear measurement using : i) Pacing ii) Digital Tape

Description : Explain in brief linear measurement using : i) Pacing ii) Digital Tape 

Last Answer : i) Pacing : This method is used only for knowing approximate distance between the objects. In preliminary survey this method can be used for linear measurement. This method consists of counting the ... and compact and measures accurate reading. The maximum measuring length of digital tape is 4.8m 

Explain with sketch torque measurement using (i) Stroboscope method, (ii) Capacitive method.

Description : Explain with sketch torque measurement using (i) Stroboscope method, (ii) Capacitive method.

Last Answer : (i) Stroboscope method:-- Explanation : The arrangement of two flanges A and B placed at a distance on the shaft is as shown. Flange A carries a scale while flange a ... By applying a radiometric algorithm to the received signals, the signed relative angle between the rotors is calculated.

Explain the procedure for measurement of vertical angle using digital theodolite

Description : Explain the procedure for measurement of vertical angle using digital theodolite

Last Answer : Digital Theodolite for measurement of vertical angle. 1)Taking out digital theodolite for box and fix it on tripod over required station. 2) Accurate centering and aapproximate leveling by leg ... required vertical angle from zenith point or horizantal plane as per setting of the instrument. 

Explain with neat labelled diagram measurement of flow using venturi meter

Description : Explain with neat labelled diagram measurement of flow using venturi meter

Last Answer : Explanation: It is a primary element of differential pressure Flow meters. 1) It consists of a straight inlet section, a converging conical inlet section, a cylindrical throat and diverging recovery ... abruptly, so permanent pressure loss or energy loss is very low as compared to orifice plate.

Explain the procedure for measurement of workability of fresh concrete using slump cone test.

Description : Explain the procedure for measurement of workability of fresh concrete using slump cone test.

Last Answer : Test Procedure: i. Clean the mould from inside and apply oil to it. ii. Place the mould on smooth horizontal, rigid & non-absorbent surface or the centre of metallic tray. iii. Fill the mould ... top of cone. vi. Based on measured slump, the degree of workability is designated as follows.

Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Description : Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Last Answer : Application: 1. In Data acquisition from low output transducers such as strain gauges, Thermocouples, Wheatstone bridge measurements e.t.c 2. In Medical instrumentation, Navigation, Radar ... video data acquisition and imaging 5. High frequency signal amplification in cable RF systems 

Draw the power and control circuit for motors using autotransformer type starter.

Description : Draw the power and control circuit for motors using autotransformer type starter.

Last Answer : Draw the power and control circuit for motors using autotransformer type starter.

Is there any way ? Is there any software or app for diabetes test , weight measurement through mobile software ?

Description : Is there any way ? Is there any software or app for diabetes test , weight measurement through mobile software ?

Last Answer : There is no such software.

What is the unit of weight measurement ?

Last Answer : One gram of weight measurement.

CO2 measurement of Fyrite kit is based on (EA c) Weight basis (dry) c) Weight basis (wet) d) Volume basis (dry) d) Volume basis (wet)

Description : CO2 measurement of Fyrite kit is based on (EA c) Weight basis (dry) c) Weight basis (wet) d) Volume basis (dry) d) Volume basis (wet)

Last Answer : volume basis

The magnitude of ‘sag correction’ during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run (c) Square of the weight of the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Description : The magnitude of sag correction' during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run ... the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Last Answer : (c) Square of the weight of the tape, in kg per m run