Which of the following factors control the design of a fluid-solid reactor? (A) Reaction kinetics for single particle (B) Size distribution of solids being treated (C) Flow patterns of solids and fluid in the reactor (D) All (A), (B) and (C)

Which of the following factors control the design of a fluid-solid
reactor?
(A) Reaction kinetics for single particle
(B) Size distribution of solids being treated
(C) Flow patterns of solids and fluid in the reactor
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Kinetics of a solid catalysed reaction can best be studied in a __________ reactor. (A) Batch (B) Plug-flow (C) Mixed (D) None of these

Description : Kinetics of a solid catalysed reaction can best be studied in a __________ reactor. (A) Batch (B) Plug-flow (C) Mixed (D) None of these

Last Answer : (C) Mixed

Kinetics of a catalytic reaction can be best studied on a/an __________ reactor. (A) Mixed (B) Integral (plug flow) (C) Differential (flow) (D) Either (A), (B) and (C)

Description : Kinetics of a catalytic reaction can be best studied on a/an __________ reactor. (A) Mixed (B) Integral (plug flow) (C) Differential (flow) (D) Either (A), (B) and (C)

Last Answer : (D) Either (A), (B) and (C)

Pick out the wrong statement. (A) 'Hold back' is defined as the fraction of material that stays longer than the mean residence time (B) Study of non-ideal flow reactor is done experimentally by stimulus￾response technique (C) For studying a chemical reaction, it is desirable to monitor the reactants during initial stages and the products during the final stages of reaction (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

Description : Pick out the wrong statement. (A) 'Hold back' is defined as the fraction of material that stays longer than the mean residence time (B) Study of non-ideal flow reactor is done experimentally ... final stages of reaction (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

Last Answer : (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is important in problems involving gas absorption without chemical reaction (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion (D) Total reflux in case of distillation operation requires infinite number of plates for a binary system separation

Description : Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is ... reflux in case of distillation operation requires infinite number of plates for a binary system separation

Last Answer : (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion

For all positive reaction orders for a particular duty, (A) Mixed reactor is always larger than the plug-flow reactor (B) Ratio of the volume of the mixed reactor to that of the plug-flow reactor decreases with order (C) Reactor size is independent of the type of flow (D) Density variation during reaction affects design

Description : For all positive reaction orders for a particular duty, (A) Mixed reactor is always larger than the plug-flow reactor (B) Ratio of the volume of the mixed reactor to that of the plug-flow ... (C) Reactor size is independent of the type of flow (D) Density variation during reaction affects design

Last Answer : (A) Mixed reactor is always larger than the plug-flow reactor

How can one determine the particle size distribution for a given bulk solid?

Description : How can one determine the particle size distribution for a given bulk solid?

Last Answer : While there are high-tech methods of performing such an analysis (laser-diffraction and video imaging system are available), the simplest way is to use a sieve stack. For example, to analyze a ... a combination of movements (shaken) to allow the solids to pass through the appropriate mesh sizes.

Coal washing waste water containing about 3% suspended solids (comprising of clay, slate, stone etc.) is treated for solid particles removal (A) By chemical coagulation (B) In sedimentation tanks equipped with mechanical scrapper (C) In vacuum filter (D) In clarifiers

Description : Coal washing waste water containing about 3% suspended solids (comprising of clay, slate, stone etc.) is treated for solid particles removal (A) By chemical coagulation (B) In sedimentation tanks equipped with mechanical scrapper (C) In vacuum filter (D) In clarifiers

Last Answer : (B) In sedimentation tanks equipped with mechanical scrapper

The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Description : The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main factor on which the behaviour of a mass of fluidised solid depends mainly is the (A) Fluid characteristics (B) Particle size (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The main factor on which the behaviour of a mass of fluidised solid depends mainly is the (A) Fluid characteristics (B) Particle size (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick out the wrong statement: (A) Chemical reactions with high activation energy are very temperature sensitive (B) A flat velocity profile exists in a plug flow reactor (C) The residence time for all the elements of fluid in case of a P.F.R. need not be same (D) Half life of a reaction increases with increased initial concentration for reaction orders more than one

Description : Pick out the wrong statement: (A) Chemical reactions with high activation energy are very temperature sensitive (B) A flat velocity profile exists in a plug flow reactor (C) The residence ... D) Half life of a reaction increases with increased initial concentration for reaction orders more than one

Last Answer : (C) The residence time for all the elements of fluid in case of a P.F.R. need not be same

Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal mixed reactor at steady state, the exit stream has the samecomposition as fluid within the reactor and the space time is equivalent toholding time for constant density system(C) Plug flow reactor (PFR) is always smaller than mixed reactor for allpositive reaction orders for a particular duty(D) Reaction rate does not decrease appreciably as the reaction proceeds incase of an autocatalytic reaction

Description : Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal ... D) Reaction rate does not decrease appreciably as the reaction proceeds in case of an autocatalytic reaction

Last Answer : (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity

The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Last Answer : (A) 3.6 AVS.ρ

Time required for 50% decomposition of a liquid in an isothermal batch reactor following first order kinetics is 2 minutes. The time required for 75% decomposition will be about __________ minutes. (A) 3 (B) 4 (C) 6 (D) 10

Description : Time required for 50% decomposition of a liquid in an isothermal batch reactor following first order kinetics is 2 minutes. The time required for 75% decomposition will be about __________ minutes. (A) 3 (B) 4 (C) 6 (D) 10

Last Answer : (B) 4

Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Description : Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Last Answer : (C) Shallow beds of solids and proper choice of particle size

The exit age distribution of fluid leaving a vessel is used to know the (A) Activation energies of a reaction (B) Reaction mechanism (C) Extent of non-ideal flow in the vessel (D) None of these

Description : The exit age distribution of fluid leaving a vessel is used to know the (A) Activation energies of a reaction (B) Reaction mechanism (C) Extent of non-ideal flow in the vessel (D) None of these

Last Answer : (C) Extent of non-ideal flow in the vessel

Why solids do not flow Using the particle theory?

Description : Why solids do not flow Using the particle theory?

Last Answer : Solids do not flow because particles in a solid are so close together and their forces of attraction are so strong that they cannot flow past one another. If you have a 8th grade Science & ... your answer that you are looking for (Using the particle theory explain why solids do not flow?)

For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Description : For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Last Answer : (D) Both (A) and (C) hold good

The settlement of a particle in sedimentation tank, is affected by A. Velocity of flow B. Viscosity of water C. Size and shape of solid D. All the above

Description : The settlement of a particle in sedimentation tank, is affected by A. Velocity of flow B. Viscosity of water C. Size and shape of solid D. All the above

Last Answer : ANS: D

In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Description : In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Last Answer : (B) Square root

In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Description : In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Last Answer : (B) Inversely proportional to

Which of the following is not an advantage of fluidisation from transferoperation point of view?(A) Intimate contact of the fluid with all parts of the solid particles(B) Lower fluid pumping power requirement(C) Minimisation of temperature variation(D) Prevention of particle segregation

Description : Which of the following is not an advantage of fluidisation from transferoperation point of view? (A) Intimate contact of the fluid with all parts of the solid particles (B) Lower fluid pumping power requirement (C) Minimisation of temperature variation (D) Prevention of particle segregation

Last Answer : (B) Lower fluid pumping power requirement

The size of plug flow reactor (PFR) for all positive reaction orders and for any given duty, is __________ that of mixed reactor. (A) Greater than (B) Equal to (C) Smaller than (D) Unpredictable from the data

Description : The size of plug flow reactor (PFR) for all positive reaction orders and for any given duty, is __________ that of mixed reactor. (A) Greater than (B) Equal to (C) Smaller than (D) Unpredictable from the data

Last Answer : (C) Smaller than

A globe valve is the most suitable for applications, in which (A) Fluid flow control is required (B) Fluid contains dispersed solid particles (C) Valve is required to be either fully open or fully closed (D) One way flow is required

Description : A globe valve is the most suitable for applications, in which (A) Fluid flow control is required (B) Fluid contains dispersed solid particles (C) Valve is required to be either fully open or fully closed (D) One way flow is required

Last Answer : (A) Fluid flow control is required

Uniform flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at successive periods of time (C) The magnitude and direction of the velocity do not change from point to point in the fluid ) The fluid particles move in plane or parallel planes and the streamline patterns are identical in each pleasure

Description : Uniform flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at ... fluid particles move in plane or parallel planes and the streamline patterns are identical in each pleasure

Last Answer : Answer: Option C

True one-dimensional flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at successive periods of time (C) The magnitude and direction of the velocity do not change from point to point in the fluid (D) The fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Description : True one-dimensional flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same ... fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Last Answer : Answer: Option A

Non uniform flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at successive periods of time (C) Velocity, depth, pressure, etc. change from point to point in the fluid flow. (D) The fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Description : Non uniform flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at ... The fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Last Answer : Answer: Option C

Steady flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at successive periods of time (C) The magnitude and direction of the velocity do not change from point to point in the fluid (D) The fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Description : Steady flow occurs when (A) The direction and magnitude of the velocity at all points are identical (B) The velocity of successive fluid particles, at any point, is the same at successive ... fluid particles move in plane or parallel planes and the streamline patterns are identical in each plane

Last Answer : Answer: Option B

For an ideal mixed flow reactor (CSTR), the exit age distribution E(t) is given by (A) A Dirac delta function (B) A step function (C) A ramp function (D) None of the above

Description : For an ideal mixed flow reactor (CSTR), the exit age distribution E(t) is given by (A) A Dirac delta function (B) A step function (C) A ramp function (D) None of the above

Last Answer : (D) None of the above

For a packed bed reactor; the presence of a long tail in the residence time distribution curve is an indication of: (A) Ideal plug flow (B) Bypass (C) Dead zone (D) Channelling

Description : For a packed bed reactor; the presence of a long tail in the residence time distribution curve is an indication of: (A) Ideal plug flow (B) Bypass (C) Dead zone (D) Channelling

Last Answer : (C) Dead zone

An isothermal irreversible reaction is being carried out in an ideal tubular flow reactor. The conversion in this case will __________ with decrease in space time. (A) Increase (B) Increase exponentially (C) Decrease (D) Remain unchanged

Description : An isothermal irreversible reaction is being carried out in an ideal tubular flow reactor. The conversion in this case will __________ with decrease in space time. (A) Increase (B) Increase exponentially (C) Decrease (D) Remain unchanged

Last Answer : (C) Decrease

A trickle bed reactor is the one, which (A) Has altogether three streams either entering or leaving (B) Processes three reactants at different flow rates (C) Processes three reactants with same flow rate (D) Employs all the three phases (i.e. solid, liquid and gas)

Description : A trickle bed reactor is the one, which (A) Has altogether three streams either entering or leaving (B) Processes three reactants at different flow rates (C) Processes three reactants with same flow rate (D) Employs all the three phases (i.e. solid, liquid and gas)

Last Answer : (D) Employs all the three phases (i.e. solid, liquid and gas)

In a fluidised bed reactor (A) Temperature gradients are very high (B) Temperature is more or less uniform (C) Hot spots are formed (D) Segregation of the solids occurs

Description : In a fluidised bed reactor (A) Temperature gradients are very high (B) Temperature is more or less uniform (C) Hot spots are formed (D) Segregation of the solids occurs

Last Answer : (B) Temperature is more or less uniform

Dean number is concerned with the (A) Fluid-particle interaction (B) Fluid flow through helical pipes (C) Power consumption in agitated vessels (D) Psychrometry

Description : Dean number is concerned with the (A) Fluid-particle interaction (B) Fluid flow through helical pipes (C) Power consumption in agitated vessels (D) Psychrometry

Last Answer : (B) Fluid flow through helical pipes

A streamline is a line in flow field, (A) That is traced by all the fluid particles passing through a given point (B) Along which a fluid particle travels (C) Such that at every point on it, the velocity is tangential to it (D) None of these

Description : A streamline is a line in flow field, (A) That is traced by all the fluid particles passing through a given point (B) Along which a fluid particle travels (C) Such that at every point on it, the velocity is tangential to it (D) None of these

Last Answer : (C) Such that at every point on it, the velocity is tangential to it

Drugs in suspensions and semi-solid formulations always degrade by (A) first order kinetics (B)second order kinetics (C) zero order kinetics (D) non-linear kinetics

Description : Drugs in suspensions and semi-solid formulations always degrade by (A) first order kinetics (B)second order kinetics (C) zero order kinetics (D) non-linear kinetics

Last Answer : (C) zero order kinetics

For multiple reactions, the flow pattern within the vessel affects the (A) Size requirement (B) Distribution of reaction products (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : For multiple reactions, the flow pattern within the vessel affects the (A) Size requirement (B) Distribution of reaction products (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The use of space time is preferred over the mean residence time in the design of a/an (A) Batch reactor (B) Ideal tubular-flow reactor (C) Slurry reactor (D) CSTR

Description : The use of space time is preferred over the mean residence time in the design of a/an (A) Batch reactor (B) Ideal tubular-flow reactor (C) Slurry reactor (D) CSTR

Last Answer : (B) Ideal tubular-flow reactor

The space time is equivalent to the holding time in a steady state mixed reactor for (A) Non-isothermal gas reaction (B) Variable fluid density systems (C) Constant fluid density systems(D) Gas reactions with changing number of moles

Description : The space time is equivalent to the holding time in a steady state mixed reactor for (A) Non-isothermal gas reaction (B) Variable fluid density systems (C) Constant fluid density systems (D) Gas reactions with changing number of moles

Last Answer : (C) Constant fluid density systems

The line traced by a single fluid particle as it moves over a period of time is called __________ line. (A) Stream (B) Path (C) Equipotential (D) None of these

Description : The line traced by a single fluid particle as it moves over a period of time is called __________ line. (A) Stream (B) Path (C) Equipotential (D) None of these

Last Answer : (B) Path

For high conversion in a highly exothermic solid catalysed reaction, use a __________ bed reactor. (A) Fixed (B) Fluidised bed reactor followed by a fixed (C) Fixed bed reactor followed by a fluidised (D) Fluidised

Description : For high conversion in a highly exothermic solid catalysed reaction, use a __________ bed reactor. (A) Fixed (B) Fluidised bed reactor followed by a fixed (C) Fixed bed reactor followed by a fluidised (D) Fluidised

Last Answer : (B) Fluidised bed reactor followed by a fixed

The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Last Answer : (B) 1/[L√(K/D1 )]

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Description : Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Description : Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Last Answer : A) 2 to 3

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

With decrease in particle size to be fluidised by a particular fluid, the operating range of fluidisation velocity (A) Widens (B) Squeezes (C) Does not change (D) Unpredictable from the data

Description : With decrease in particle size to be fluidised by a particular fluid, the operating range of fluidisation velocity (A) Widens (B) Squeezes (C) Does not change (D) Unpredictable from the data

Last Answer : (C) Does not change

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

For the non catalytic reaction of particles with surrounding fluid, the same needed to achieve the same fractional conversion for particles of different unchanging sizes is proportional to the particle diameter, when the __________ is the controlling resistance. (A) Film diffusion (B) Diffusion through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Description : For the non catalytic reaction of particles with surrounding fluid, the same needed to achieve the same fractional conversion for particles of different unchanging sizes is proportional to the particle diameter, when the ... through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Last Answer : (C) Chemical reaction

For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, when the __________ is the controlling resistance. (A) Film diffusion (B) Diffusion through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Description : For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, ... through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Last Answer : (B) Diffusion through ash layer