The main factor on which the behaviour of a mass of fluidised solid depends mainly is the (A) Fluid characteristics (B) Particle size (C) Both (A) and (B) (D) Neither (A) nor (B)

The main factor on which the behaviour of a mass of fluidised solid
depends mainly is the
(A) Fluid characteristics
(B) Particle size
(C) Both (A) and (B)
(D) Neither (A) nor (B)
by

1 Answer

Answer :

(C) Both (A) and (B)
by

Related questions

The uniformity of a gas fluidised bed depends upon the __________ of the solid particles. (A) Size (B) Surface properties (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The uniformity of a gas fluidised bed depends upon the __________ of the solid particles. (A) Size (B) Surface properties (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

With decrease in particle size to be fluidised by a particular fluid, the operating range of fluidisation velocity (A) Widens (B) Squeezes (C) Does not change (D) Unpredictable from the data

Description : With decrease in particle size to be fluidised by a particular fluid, the operating range of fluidisation velocity (A) Widens (B) Squeezes (C) Does not change (D) Unpredictable from the data

Last Answer : (C) Does not change

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

Slugging occurs in a fluidised bed, if the bed is (A) Narrow (B) Deep (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Slugging occurs in a fluidised bed, if the bed is (A) Narrow (B) Deep (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Description : Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Last Answer : (C) Combination of solid & liquid

Isothermal turbulent flow of a fluid results in decrease of its pressure, which depends on the (A) Wall roughness (B) Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Isothermal turbulent flow of a fluid results in decrease of its pressure, which depends on the (A) Wall roughness (B) Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The internal energy of an incompressible fluid depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The internal energy of an incompressible fluid depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Description : The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Thermal conductivity of a conducting solid material depends upon its (A) Temperature (B) Porosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Thermal conductivity of a conducting solid material depends upon its (A) Temperature (B) Porosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

For a solid catalysed chemical reaction, the effectiveness of solid catalyst depends upon the __________ adsorption. (A) Physical (B) Chemical (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : For a solid catalysed chemical reaction, the effectiveness of solid catalyst depends upon the __________ adsorption. (A) Physical (B) Chemical (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (B) Chemical

Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The effect of solid boundary on the fluid flow is confined to the boundary layer, except for fluids (A) Having high viscosities (B) Moving at low velocities (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The effect of solid boundary on the fluid flow is confined to the boundary layer, except for fluids (A) Having high viscosities (B) Moving at low velocities (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Filtration capacity of a rotary drum vacuum filter depends upon the (A) Cake thickness (B) Characteristics of the feed slurry (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Filtration capacity of a rotary drum vacuum filter depends upon the (A) Cake thickness (B) Characteristics of the feed slurry (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Pick out the correct statement. (A) A forced vortex occurs when fluid rotates as a solid about an axis (B) In laminar flow, Newton's law of viscosity does not apply (C) A free vortex occurs, when fluid rotates as a solid (D) In turbulent flow, there are neither cross-currents nor eddies

Description : Pick out the correct statement. (A) A forced vortex occurs when fluid rotates as a solid about an axis (B) In laminar flow, Newton's law of viscosity does not apply (C) A free vortex occurs, when fluid rotates as a solid (D) In turbulent flow, there are neither cross-currents nor eddies

Last Answer : (A) A forced vortex occurs when fluid rotates as a solid about an axis

Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Fanning friction factor equation applies to the __________ fluid flow. (A) Non-isothermal condition of (B) Compressible (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Fanning friction factor equation applies to the __________ fluid flow. (A) Non-isothermal condition of (B) Compressible (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Description : Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Description : Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Last Answer : (C) Shallow beds of solids and proper choice of particle size

Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Description : Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

In a grinding operation, the limiting particle size is the size of the __________ particle in the sample. (A) Smallest (B) Largest (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : In a grinding operation, the limiting particle size is the size of the __________ particle in the sample. (A) Smallest (B) Largest (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'

Description : The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'

Last Answer : (A) Carbon

In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Description : In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Last Answer : (B) Square root

In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Description : In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Last Answer : (B) Inversely proportional to

Which of the following factors control the design of a fluid-solid reactor? (A) Reaction kinetics for single particle (B) Size distribution of solids being treated (C) Flow patterns of solids and fluid in the reactor (D) All (A), (B) and (C)

Description : Which of the following factors control the design of a fluid-solid reactor? (A) Reaction kinetics for single particle (B) Size distribution of solids being treated (C) Flow patterns of solids and fluid in the reactor (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of catalyst, if it doesnot entail a chain mechanism.(A) Proportional to(B) Independent of(C) Inversely proportional to(D) Proportional to the square o

Description : Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of ... to (B) Independent of (C) Inversely proportional to (D) Proportional to the square o

Last Answer : (A) Proportional to

Noise produced by cooling fans (employed in air cooled heat exchangers or cooling tower) is mainly caused due to the turbulence created by blade passage through air. It can be reduced by use of a slower fan (A) With greater number of blades (B) Of increased diameter (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Noise produced by cooling fans (employed in air cooled heat exchangers or cooling tower) is mainly caused due to the turbulence created by blade passage through air. It can be reduced by use of a slower fan (A) With greater ... (B) Of increased diameter (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Capacity of a rotary dryer depends on its (A) rpm (B) Inclination with ground surface (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Capacity of a rotary dryer depends on its (A) rpm (B) Inclination with ground surface (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Description : Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (A) Heat balance consideration

The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Natural draft created by the chimney depends upon (A) Temperature of the flue gas (B) Its height (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Natural draft created by the chimney depends upon (A) Temperature of the flue gas (B) Its height (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Natural draught produced by a chimney depends upon the (A) Density of the chimney gases (B) Height of the chimney (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Natural draught produced by a chimney depends upon the (A) Density of the chimney gases (B) Height of the chimney (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Joule-Thomson co-efficient depends on the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Joule-Thomson co-efficient depends on the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Entropy of an ideal gas depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Entropy of an ideal gas depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Applicability of Bernoulli's equation is limited to a/an __________ fluid, that does not exchange shaft work with the surroundings. (A) Incompressible (B) Non-viscous (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Applicability of Bernoulli's equation is limited to a/an __________ fluid, that does not exchange shaft work with the surroundings. (A) Incompressible (B) Non-viscous (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

. In magnetic flow meters, voltage generation is (A) Due to the motion of conducting fluid through an externally generated uniform field (B) Proportional to the fluid velocity (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : . In magnetic flow meters, voltage generation is (A) Due to the motion of conducting fluid through an externally generated uniform field (B) Proportional to the fluid velocity (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In case of a P.F.R., there (A) May be lateral mixing of fluid (B) Should not be any mixing along the flow path (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In case of a P.F.R., there (A) May be lateral mixing of fluid (B) Should not be any mixing along the flow path (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

A particle moving with uniform speed can possess : (a) radial acceleration (b) tangential acceleration © both radial and tangential accelerations (d) neither radial nor tangential acceleration

Description : A particle moving with uniform speed can possess :  (a) radial acceleration (b) tangential acceleration © both radial and tangential accelerations (d) neither radial nor tangential acceleration

Last Answer : Neither radial nor tangential... as if it move in a straight line.. but it possess radial acceleration if it moves in a uniform circular path

For __________ drying, the effects of velocity, temperature and humidity of the gas and the thickness of the solid are the same. (A) Unsaturated surface (B) Constant rate (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : For __________ drying, the effects of velocity, temperature and humidity of the gas and the thickness of the solid are the same. (A) Unsaturated surface (B) Constant rate (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Non-catalytic fluid-solid reactions are represented by __________ model. (A) Continuous reaction (B) Unreacted core (C) Both (A) and (B) (D) Neither (A) and (B)

Description : Non-catalytic fluid-solid reactions are represented by __________ model. (A) Continuous reaction (B) Unreacted core (C) Both (A) and (B) (D) Neither (A) and (B)

Last Answer : (C) Both (A) and (B)

Fluidised beds are formed, when the (A) Fluid friction is zero (B) Gravity force is less than the fluid friction (C) Pressure forces equal gravity forces (D) Sum of the fluid friction and pressure forces is equal and opposite to gravity forces

Description : Fluidised beds are formed, when the (A) Fluid friction is zero (B) Gravity force is less than the fluid friction (C) Pressure forces equal gravity forces (D) Sum of the fluid friction and pressure forces is equal and opposite to gravity forces

Last Answer : (B) Gravity force is less than the fluid friction

A catalyst in a chemical reaction __________ free energy change in the reaction. (A) Increases (B) Decreases (C) Either (A) or (B); depends on the type of catalyst (D) Neither (A) nor (B)

Description : A catalyst in a chemical reaction __________ free energy change in the reaction. (A) Increases (B) Decreases (C) Either (A) or (B); depends on the type of catalyst (D) Neither (A) nor (B)

Last Answer : (C) Either (A) or (B); depends on the type of catalyst

Quality of transmission depends upon (1) Nature of signal only (2) Nature of medium only (3) Both (1) and (2) (4) Neither A nor B

Description : Quality of transmission depends upon (1) Nature of signal only (2) Nature of medium only (3) Both (1) and (2) (4) Neither A nor B

Last Answer : (3) Both (1) and (2) Explanation: Quality of transmission is governed both by nature of signal and nature of communication channel/medium.

The field capacity of a soil depends upon a. Capillary tension in soil b. Porosity of soil c. Both (a) and (b) d. Neither (a) nor (b)

Description : The field capacity of a soil depends upon a. Capillary tension in soil b. Porosity of soil c. Both (a) and (b) d. Neither (a) nor (b)

Last Answer : c. Both (a) and (b)

For high conversion in a highly exothermic solid catalysed reaction, use a __________ bed reactor. (A) Fixed (B) Fluidised bed reactor followed by a fixed (C) Fixed bed reactor followed by a fluidised (D) Fluidised

Description : For high conversion in a highly exothermic solid catalysed reaction, use a __________ bed reactor. (A) Fixed (B) Fluidised bed reactor followed by a fixed (C) Fixed bed reactor followed by a fluidised (D) Fluidised

Last Answer : (B) Fluidised bed reactor followed by a fixed