A Rotameter through which air at room temperature and atmospheric pressure is flowing gives a certain reading for a flow rate of 100 cc/sec. If helium (molecular weight 4) is used and Rotameter shows the same reading, the flow rate (cc/sec) is(A) 26(B) 42(C) 269(D) 325

A Rotameter through which air at room temperature and atmospheric
pressure is flowing gives a certain reading for a flow rate of 100 cc/sec. If
helium (molecular weight 4) is used and Rotameter shows the same reading,
the flow rate (cc/sec) is
(A) 26
(B) 42
(C) 269
(D) 325
by

1 Answer

Answer :

(C) 269
by

Related questions

Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure d. Volume of 1 kg of dry air at 21°C and atmospheric pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Description : Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure ... pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Last Answer : Answer: D

A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then for the same flow rate of water the new manometer reading will be __________ cms. (A) 17 (B) 42(C) 84 (D) 1.8

Description : A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then ... new manometer reading will be __________ cms. (A) 17 (B) 42 (C) 84 (D) 1.8

Last Answer : __________ cms. (A) 17

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

A disk drive has 100 cylinders, numbered 0 to 99. Disk requests come to the disk driver for cyclinders 12, 26, 24, 4, 42, 8 and 50 in that order. The driver is currently serving a request at cyclinder 24. A seek takes 6 msec per cyclinder moved. How much seek time is needed for shortest seek time first (SSTF) algorithm? (A) 0.984 sec (B) 0.396 sec (C) 0.738 sec (D) 0.42 sec

Description : A disk drive has 100 cylinders, numbered 0 to 99. Disk requests come to the disk driver for cyclinders 12, 26, 24, 4, 42, 8 and 50 in that order. The driver is currently serving a request at cyclinder 24. A seek takes ... (SSTF) algorithm? (A) 0.984 sec (B) 0.396 sec (C) 0.738 sec (D) 0.42 sec

Last Answer : C

Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10(C) 100 (D) 1000 Answer:

Description : Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10 (C) 100 (D) 1000 Answer:

Last Answer : (D) 1000

In area meter (e.g., Rotameter), with increase in the fluid flow rate, the (A) Pressure drop increases linearly (B) Pressure drop is almost constant (C) Area through which fluid flows does not vary (D) None of these

Description : In area meter (e.g., Rotameter), with increase in the fluid flow rate, the (A) Pressure drop increases linearly (B) Pressure drop is almost constant (C) Area through which fluid flows does not vary (D) None of these

Last Answer : (B) Pressure drop is almost constant

Water is flowing through a 1 foot diameter pipe at the rate of 10ft/sec. What is the volume flow rate of water in ft³/sec?  a. 7.85  b. 6.85  c. 8.85  d. 5.85 V = Aν

Description : Water is flowing through a 1 foot diameter pipe at the rate of 10ft/sec. What is the volume flow rate of water in ft³/sec?  a. 7.85  b. 6.85  c. 8.85  d. 5.85 V = Aν

Last Answer : 7.85

Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids (C) Particles movement from higher concentration to lower concentration takes place in diffusion process (D) According to Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Description : Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids ( ... Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Last Answer : (B) Molecular diffusion in solid is much faster than that in liquids

In a/an __________, the flow rate of fluids is obtained by measuring the difference between the impact and the static pressure. (A) Rotameter (B) Pitot tube (C) Venturimeter (D) Flow nozzle

Description : In a/an __________, the flow rate of fluids is obtained by measuring the difference between the impact and the static pressure. (A) Rotameter (B) Pitot tube (C) Venturimeter (D) Flow nozzle

Last Answer : (B) Pitot tube

Flow rate of high velocity flue gas discharged through a stack to the atmosphere can be most conveniently measured by a (A) Pitot tube (B) Manometer (C) Rotameter (D) None of these

Description : Flow rate of high velocity flue gas discharged through a stack to the atmosphere can be most conveniently measured by a (A) Pitot tube (B) Manometer (C) Rotameter (D) None of these

Last Answer : (A) Pitot tube

Calculate: a. Mass flow rate in lb/hr. b. The velocity at section 2 in fps  a. 800,000lb/hr;625ft/s  b. 900,000lb/hr;625 ft/s  c. 888,000lb/hr;269 ft/s  d. 700,000lb/hr;269 ft/s m = A1V!/V1

Description : Calculate: a. Mass flow rate in lb/hr. b. The velocity at section 2 in fps  a. 800,000lb/hr;625ft/s  b. 900,000lb/hr;625 ft/s  c. 888,000lb/hr;269 ft/s  d. 700,000lb/hr;269 ft/s m = A1V!/V1

Last Answer : 900,000 lb/hr;625 ft/s

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the first fluid, the pressure drop will (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Description : Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the ... (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Last Answer : (B) Decrease

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

In veins, valves are present to check backward flow of blood flowing at (a) atmospheric pressure (b) high pressure (c) low pressure (d) all of these.

Description : In veins, valves are present to check backward flow of blood flowing at (a) atmospheric pressure (b) high pressure (c) low pressure (d) all of these.

Last Answer : (c) low pressure

Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Description : Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Last Answer : (C) Exit fluid temperature = wall temperature

Water flow rate in a pipe of 3.5 metres diameter can be most economically and conveniently measured by a/an (A) Pitot tube (B) Venturimeter (C) Orificemeter (D) Rotameter

Description : Water flow rate in a pipe of 3.5 metres diameter can be most economically and conveniently measured by a/an (A) Pitot tube (B) Venturimeter (C) Orificemeter (D) Rotameter

Last Answer : (A) Pitot tube

Which of the following can be used for the direct measurement of volumetric flow rate of slurry? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Description : Which of the following can be used for the direct measurement of volumetric flow rate of slurry? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Last Answer : (C) Rotameter

Drag force on the float of a Rotameter is (where Q = flow rate of the) (A) ∝ Q (B) ∝ √Q (C) ∝ Q2 (D) Constant

Description : Drag force on the float of a Rotameter is (where Q = flow rate of the) (A) ∝ Q (B) ∝ √Q (C) ∝ Q2 (D) Constant

Last Answer : (D) Constant

Which is the most efficient and best for measuring very small flow rate of gases? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Flow nozzle

Description : Which is the most efficient and best for measuring very small flow rate of gases? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Flow nozzle

Last Answer : (C) Rotameter

the fluid flow rate increases, the float of the Rotameter (A) Rises in the tube (B) Rotates at higher speed (C) Rotates at lower speed (D) Drops down in the tube

Description : the fluid flow rate increases, the float of the Rotameter (A) Rises in the tube (B) Rotates at higher speed (C) Rotates at lower speed (D) Drops down in the tube

Last Answer : Option A

All gases except __________ shows a cooling effect during throttling process at atmospheric temperature and pressure. (A) Oxygen (B) Nitrogen (C) Air (D) Hydrogen

Description : All gases except __________ shows a cooling effect during throttling process at atmospheric temperature and pressure. (A) Oxygen (B) Nitrogen (C) Air (D) Hydrogen

Last Answer : (D) Hydrogen

12.28× 1.5 -36÷ 2.4 = ? a) 3.24 b) 7.325 c) 6.42 d) 4.32 e) None of these

Description : 12.28× 1.5 -36÷ 2.4 = ? a) 3.24 b) 7.325 c) 6.42 d) 4.32 e) None of these

Last Answer : 12.28 × 1.5 - 15 = ? 18.42 - 15 = ? ? = 3.42 Answer: e)

The pressure head of a flow meter remains constant for (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Description : The pressure head of a flow meter remains constant for (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Last Answer : (C) Rotameter

Out of the following flow measuring devices, which one incurs themaximum installation cost as well as pressure loss? (A) Flow nozzle (B) Venturimeter (C) Rotameter (D) Orificemeter

Description : Out of the following flow measuring devices, which one incurs themaximum installation cost as well as pressure loss? (A) Flow nozzle (B) Venturimeter (C) Rotameter (D) Orificemeter

Last Answer : (B) Venturimeter

The specific volume of air is expressed as the volume of: a. 1 kg of air at 101.325 kPa in cm3 b. 0.833 kg of air at standard pressure and temperature in m3 c. 1 kg of air at 101.325 kPa and 21 degrees Celsius in m3 d. 1 g of air occupied at any temperature and pressure e. 1 kg of air, regardless of temperature and pressure

Description : The specific volume of air is expressed as the volume of: a. 1 kg of air at 101.325 kPa in cm3 b. 0.833 kg of air at standard pressure and temperature in m3 c. 1 kg of air at 101.325 ... d. 1 g of air occupied at any temperature and pressure e. 1 kg of air, regardless of temperature and pressure

Last Answer : Answer: C

Water is flowing at 1 m/sec through a pipe (of 10 cm I.D) with a right angle bend. The force in Newtons exerted on the bend by water is (A) 10 √2π (B) 5π/2 (C) 5 √2π (D) 5π/√2

Description : Water is flowing at 1 m/sec through a pipe (of 10 cm I.D) with a right angle bend. The force in Newtons exerted on the bend by water is (A) 10 √2π (B) 5π/2 (C) 5 √2π (D) 5π/√2

Last Answer : (B) 5π/2

A pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/sec, the average velocity through the bifurcated pipes is (A) 20 m/sec (B) 10 m/sec (C) 5 √2 m/sec (D) 5 m/sec

Description : A pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/sec, the average velocity through the bifurcated pipes is (A) 20 m/sec (B) 10 m/sec (C) 5 √2 m/sec (D) 5 m/sec

Last Answer : (B) 10 m/sec

Rotameter is a device used to measure (A) Absolute pressure (B) Velocity of fluid (C) Flow (D) Rotation

Description : Rotameter is a device used to measure (A) Absolute pressure (B) Velocity of fluid (C) Flow (D) Rotation

Last Answer : Answer: Option C

Calculate coefficient of viscous damper, if the system is critically damped. Consider the following data: 1. Mass of spring mass damper system = 350 kg 2. Static deflection = 2 x 10 –3 m 3. Natural frequency of the system = 60 rad/sec A. 100.5 x 10 3 N-s/m B. 80 x 10 3 N-s/m C. 42 x 10 3 N-s/m D. None of the above

Description : Calculate coefficient of viscous damper, if the system is critically damped. Consider the following data: 1. Mass of spring mass damper system = 350 kg 2. Static deflection = 2 x 10 -3 m 3. Natural frequency of the system = 60 rad/sec ... /m B. 80 x 10 3 N-s/m C. 42 x 10 3 N-s/m D. None of the above

Last Answer : C. 42 x 10 3 N-s/m

Calculate coefficient of viscous damper, if the system is critically damped. Consider the following data: 1. Mass of spring mass damper system = 350 kg 2. Static deflection = 2 x 10 –3 m 3. Natural frequency of the system = 60 rad/sec a. 100.5 x 10 3 N-s/m b. 80 x 10 3 N-s/m c. 42 x 10 3 N-s/m d. None of the above

Description : Calculate coefficient of viscous damper, if the system is critically damped. Consider the following data: 1. Mass of spring mass damper system = 350 kg 2. Static deflection = 2 x 10 -3 m 3. Natural frequency of the system = 60 rad/sec ... /m b. 80 x 10 3 N-s/m c. 42 x 10 3 N-s/m d. None of the above

Last Answer : c. 42 x 10 3 N-s/m

According to Dalton’s law, the total pres sure of the mixture of gases is equal to  (a) greater of the partial pressures of all  (b) average of the partial pressures of all  (c) sum of the partial pressures of all  (d) sum of the partial pressures of all divided by average molecular weight  (e) atmospheric pressure.

Description : According to Dalton's law, the total pres sure of the mixture of gases is equal to  (a) greater of the partial pressures of all  (b) average of the partial pressures of all  (c) sum ... all  (d) sum of the partial pressures of all divided by average molecular weight  (e) atmospheric pressure.

Last Answer : Answer : c

The intraocular pressure: a. shows a higher diurnal variation in glaucoma patients b. is highest in the morning c. gives a falsely higher reading in patients with thick cornea d. all

Description : The intraocular pressure: a. shows a higher diurnal variation in glaucoma patients b. is highest in the morning c. gives a falsely higher reading in patients with thick cornea d. all

Last Answer : all

Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Description : Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Last Answer : (B) 0.62

Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Description : Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Last Answer : (B) 0.62

A sample of natural gas containing 80% methane (CH4 ) and rest nitrogen (N2 ) is burnt with 20% excess air. With 80% of the combustibles producing CO2 and the remainder going to CO, the Orsat analysis in volume percent is (A) CO2 : 6.26, CO : 1.56, O2 : 3.91, H2O :15.66, N2 : 72.60 (B) CO2 : 7.42, CO : 1.86, O2 : 4.64, N2 :86.02 (C) CO2 : 6.39, CO : 1.60, O2 : 3.99, H2O:25.96, N2 :72.06 (D) CO2 : 7.60, CO : 1.90, O2 : 4.75, N2 : 85.74

Description : A sample of natural gas containing 80% methane (CH4 ) and rest nitrogen (N2 ) is burnt with 20% excess air. With 80% of the combustibles producing CO2 and the remainder going to CO, the Orsat analysis in volume percent is (A) CO2 : 6 ... 96, N2 :72.06 (D) CO2 : 7.60, CO : 1.90, O2 : 4.75, N2 : 85.74

Last Answer : (B) CO2 : 7.42, CO : 1.86, O2 : 4.64, N2 :86.02

The average molecular weight of a flue gas having the composition by volume as CO2 = 25%, O2 = 25%, N2 = 50% will be (A) 27.6 (B) 23 (C) 47.3 (D) 42.9

Description : The average molecular weight of a flue gas having the composition by volume as CO2 = 25%, O2 = 25%, N2 = 50% will be (A) 27.6 (B) 23 (C) 47.3 (D) 42.9

Last Answer : (B) 23

Refractive index of a petrofuel which is the ratio of velocity of light in air to its velocity in the petrofuel gives an indication if its (A) Molecular weight (B) Aromatics content (C) Both ‘a’ & ‘b’ (D) Neither ‘a’ nor ‘b’

Description : Refractive index of a petrofuel which is the ratio of velocity of light in air to its velocity in the petrofuel gives an indication if its (A) Molecular weight (B) Aromatics content (C) Both ‘a’ & ‘b’ (D) Neither ‘a’ nor ‘b’

Last Answer : (C) Both ‘a’ & ‘b

A stone of wight 100 kg is thrown vertically upwards by a man of height y = 1.8 m with an initial velocity of 20 m/sec. The maximum height to which it will rise would be a.22.2 m b.26 m c.15.1 m d.20.2 m e.10 m

Description : A stone of wight 100 kg is thrown vertically upwards by a man of height y = 1.8 m with an initial velocity of 20 m/sec. The maximum height to which it will rise would be a.22.2 m b.26 m c.15.1 m d.20.2 m e.10 m

Last Answer : a. 22.2 m

The self-cleansing velocity of water flowing through pipe lines, is A. 2 metres/sec B. 1 metre/sec C. 0.5 metre/sec D. 0.25 metre/sec

Description : The self-cleansing velocity of water flowing through pipe lines, is A. 2 metres/sec B. 1 metre/sec C. 0.5 metre/sec D. 0.25 metre/sec

Last Answer : ANS: A

A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Description : A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Last Answer : (D) Temperature of the solid

Flow measurement in an open channel is done by a/an (A) Venturimeter (B) Orificemeter (C) Weir (D) Rotameter

Description : Flow measurement in an open channel is done by a/an (A) Venturimeter (B) Orificemeter (C) Weir (D) Rotameter

Last Answer : (C) Weir

Open channel liquid flow is most conveniently measured by a (A) Hot wire anemometer (B) Notch (C) Rotameter (D) Segmental orifice

Description : Open channel liquid flow is most conveniently measured by a (A) Hot wire anemometer (B) Notch (C) Rotameter (D) Segmental orifice

Last Answer : (B) Notch

Which of the following may be termed as a variable orifice flow-meter? (A) Rotameter (B) Pitot tube (C) V-notch (D) All (A), (B) and (C)

Description : Which of the following may be termed as a variable orifice flow-meter? (A) Rotameter (B) Pitot tube (C) V-notch (D) All (A), (B) and (C)

Last Answer : (A) Rotameter

. It is possible to integrate an automatic flow controller to a (A) Flow nozzle (B) Venturimeter (C) Rotameter (D) None of these

Description : . It is possible to integrate an automatic flow controller to a (A) Flow nozzle (B) Venturimeter (C) Rotameter (D) None of these

Last Answer : (C) Rotameter

Which of the following flow measuring devices is an area meter? (A) Venturimeter (B) Orificemeter (C) Anemometer (D) Rotameter

Description : Which of the following flow measuring devices is an area meter? (A) Venturimeter (B) Orificemeter (C) Anemometer (D) Rotameter

Last Answer : (D) Rotameter

Which of the following is used for very accurate measurement of flow of gas at low velocity? (A) Pitot tube (B) Rotameter (C) Segmental orificemeter (D) Hot wire anemometer

Description : Which of the following is used for very accurate measurement of flow of gas at low velocity? (A) Pitot tube (B) Rotameter (C) Segmental orificemeter (D) Hot wire anemometer

Last Answer : (D) Hot wire anemometer

Maximum stability of white phosphorous is at (A) Very high pressure (B) Atmospheric pressure (C) Room temperature (D) > 600°C

Description : Maximum stability of white phosphorous is at (A) Very high pressure (B) Atmospheric pressure (C) Room temperature (D) > 600°C

Last Answer : (D) > 600°C

Absolute Zero is defined as – (1) The temperature at which all molecular motion ceases (2) At which water boils at 298K (3) At which liquid Helium boils (4) At which the volume becomes zero

Description : Absolute Zero is defined as – (1) The temperature at which all molecular motion ceases (2) At which water boils at 298K (3) At which liquid Helium boils (4) At which the volume becomes zero

Last Answer : (1) The temperature at which all molecular motion ceases Explanation: Absolute zero is the temperature at which all motion in matter stops and is thought to be unreachable. It is ... nature have minimal vibrational motion, retaining only quantum mechanical, zero-point energy-induced particle motion.