The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

The heating capacity of continuous reheating furnace depends upon the
(A) Hearth area and furnace temperature
(B) Emissivity of the stock
(C) Ratio of wall surface to stock surface
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Last Answer : (B) Reheating furnace

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Last Answer : (A) Cold rolled steel coil annealing

__________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Last Answer : (B) Muffle furnace

An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Last Answer : (A) Walking beam

Heat transfer rate to the stock/charge in the furnace does not depend upon the(A) Emissivity of the refractory walls(B) Size of the furnace(C) Use of waste heat recovery equipments(D) Thickness of the stock

Description : Heat transfer rate to the stock/charge in the furnace does not depend upon the (A) Emissivity of the refractory walls (B) Size of the furnace (C) Use of waste heat recovery equipments (D) Thickness of the stock

Last Answer : (C) Use of waste heat recovery equipments

Which of the following variables does not affect the furnace capacity? (A) Size of the furnace (B) Gas velocity in furnace (C) Ratio of wall surface to surface of stock (D) None of these

Description : Which of the following variables does not affect the furnace capacity? (A) Size of the furnace (B) Gas velocity in furnace (C) Ratio of wall surface to surface of stock (D) None of these

Last Answer : (D) None of these

Unit of furnace loading is (A) Ton stock/hr/m2 hearth area (B) Ton stock/hr (C) Ton stock/m2 hearth area (D) Both (B) and (C)

Description : Unit of furnace loading is (A) Ton stock/hr/m2 hearth area (B) Ton stock/hr (C) Ton stock/m2 hearth area (D) Both (B) and (C)

Last Answer : (A) Ton stock/hr/m2 hearth area

Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock(D) All (A), (B) and (C)

Description : Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Description : Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Last Answer : (B) Slabs

The rate of scaling of furnace stock depends upon the (A) Temperature (B) Time(C) Nature of atmosphere(D) All (A), (B) and (C)

Description : The rate of scaling of furnace stock depends upon the (A) Temperature (B) Time (C) Nature of atmosphere (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Description : Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Last Answer : (D) None of these

If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Last Answer : (B) Underfired

Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these

Description : A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these

Last Answer : (B) Muffle furnace

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

Which is not accomplished in an underfired furnace? (A) Increase in heating capacity/m2 of floor space (B) Elimination of cold spot at the bottom of the charge (C) Reduction in the temperature of furnace gases (D) Protection of the periphery of the charge from excessive radiation

Description : Which is not accomplished in an underfired furnace? (A) Increase in heating capacity/m2 of floor space (B) Elimination of cold spot at the bottom of the charge (C) Reduction in the temperature of furnace gases (D) Protection of the periphery of the charge from excessive radiation

Last Answer : (A) Increase in heating capacity/m2 of floor space

Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Last Answer : (C) Boiler furnace

An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Last Answer : (B) Muffle furnace

The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Last Answer : (B) 40

Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Description : Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Last Answer : (B) Annealing furnace

Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Description : Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Last Answer : (D) Boiler furnace

Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Last Answer : (C) Soaking pit

Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln

Description : Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln

Last Answer : (B) Reverberatory furnace

Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace(C) Steam boiler(D) Coke oven

Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven

Last Answer : (D) Coke oven

Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Description : Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Last Answer : (A) Cupola

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The amount of combustible escaping unconsumed from the furnace, depends upon the (A) Air supplied and furnace temperature (B) Burner design (thoroughness of mixing versus stratification) (C) Air preheat and the flow of gases in the furnace (mixing by induction, by acceleration or by change of direction) (D) All (A), (B) and (C)

Description : The amount of combustible escaping unconsumed from the furnace, depends upon the (A) Air supplied and furnace temperature (B) Burner design (thoroughness of mixing versus stratification) (C) Air preheat and the flow of ... , by acceleration or by change of direction) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the(A) Quantity & temperature of waste gas(B) Dust concentration & nature of dust in waste gas(C) Corrosive nature of the waste gas(D) All (A), (B) and (C)

Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)

Last Answer : (B) Dust concentration & nature of dust in waste gas

Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Last Answer : (C) Tunnel kiln

Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80

Description : Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80

Last Answer : (B) 20

Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Last Answer : (A) By-product coke oven

An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Last Answer : (A) Soaking pit

Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola

Description : Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola

Last Answer : (C) Cupola

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Last Answer : compressor

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

Air at a particular humidity is heated in a furnace. The new dew point (A) Decreases (B) Increases (C) Depends on the extent of heating (D) Remain unchanged

Description : Air at a particular humidity is heated in a furnace. The new dew point (A) Decreases (B) Increases (C) Depends on the extent of heating (D) Remain unchanged

Last Answer : (B) Increases

Thickness of stock does not affect the fuel economy of furnaces, if thematerial to be heated is of(A) Low emissivity(B) High thermal conductivity(C) Both (A) and (B)(D) Neither (A) nor (B)

Description : Thickness of stock does not affect the fuel economy of furnaces, if thematerial to be heated is of (A) Low emissivity (B) High thermal conductivity (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above

Description : Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above

Last Answer : Answer: Option D

The thermal radiative flux from a surface of emissivity = 0.4 is 22.68 kW/m2 . The approximate surface temperature (K) is (Stefan-Boltzmann constant = 5.67 × 10 -8 W/m2 .K4 )(A) 1000(B) 727(C) 800(D) 1200

Description : The thermal radiative flux from a surface of emissivity = 0.4 is 22.68 kW/m2 . The approximate surface temperature (K) is (Stefan-Boltzmann constant = 5.67 × 10 -8 W/m2 .K4 ) (A) 1000 (B) 727 (C) 800 (D) 1200

Last Answer : (A) 1000

Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness (C) The emissivity of a polished surface is quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Description : Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness ... quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Last Answer : (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Description : Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Last Answer : Option D

Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Description : Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)