Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these
Last Answer : (B) Muffle furnace
Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating
Last Answer : (A) Cold rolled steel coil annealing
Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola
Last Answer : (B) Reheating furnace
Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these
Last Answer : (A) Soaking pit
Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace
Last Answer : (C) Soaking pit
Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven
Last Answer : (D) Coke oven
Description : Example of an indirectly heated furnace is (A) Hood annealing furnace (B) Muffle furnace (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth
Last Answer : (A) Walking beam
Description : Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln
Last Answer : (B) Annealing furnace
Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace
Last Answer : (C) Tunnel kiln
Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns
Last Answer : (C) Boiler furnace
Description : Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the flue gas outlet temperature from the soaking pit is 1200°C. (A) 5 (B) 60 (C) 20 (D) 40
Last Answer : (C) 20
Description : Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter
Last Answer : (B) Blast furnace
Description : An example of shaft furnace is the (A) L.D. converter (B) Glass melting tank (C) Blast furnace (D) Soaking pit
Last Answer : (C) Blast furnace
Description : Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80
Last Answer : (B) 20
Description : Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these
Last Answer : (D) None of these
Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)
Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace
Last Answer : (A) By-product coke oven
Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)
Description : Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola
Last Answer : (C) Cupola
Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85
Last Answer : (B) 40
Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating
Last Answer : (B) Underfired
Description : Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above
Last Answer : Answer: Option D
Description : A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these
Description : In a muffle furnace, the muffle (A) Retards the heat transfer (B) Assists in temperature equalisation in the charge (C) Permits the use of controlled atmosphere for the protection of stock (D) All (A), (B) and (C)
Description : The main function of a muffle in the muffle furnace is to (A) Protect the charge from the effects of the products of combustion (B) Smooth out temperature inequalities on the combustion side of the muffle wall (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted
Last Answer : (C) Radiation
Description : In which of the following furnaces, the gases are sucked through the stock bed from below? (A) Soaking pit (B) Sintering machine (C) Beehive oven (D) None of these
Last Answer : (B) Sintering machine
Description : Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace
Last Answer : (D) Boiler furnace
Description : Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets
Last Answer : (B) Slabs
Description : Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln
Last Answer : (B) Reverberatory furnace
Description : Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these
Last Answer : (A) Cupola
Description : Unit of furnace loading is (A) Ton stock/hr/m2 hearth area (B) Ton stock/hr (C) Ton stock/m2 hearth area (D) Both (B) and (C)
Last Answer : (A) Ton stock/hr/m2 hearth area
Description : Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits
Last Answer : (A) By-product coke ovens
Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor
Last Answer : compressor
Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above
Last Answer : Billet Reheating Furnace
Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The heat treatment cycle is as follows; Increase temperature from 30 OC to 850 OC in 3 hours. ... efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50
Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30) = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8
Description : An element of a CRT, that releases electrons when heated indirectly by a filament
Last Answer : cathode
Description : A mixture of phosphate rock __________ is heated in an electric furnace to produce phosphorous. (A) Salt & coke (B) Sand & coke (C) And coke (D) And sand
Last Answer : (B) Sand & coke
Description : Scouring is a finishing operation during the manufacture of fibre, which aims at __________ of fibres. (A) Improving the stretchability (B) Dyeing/colouring (C) Detergent solution washing (D) Glycol soaking
Last Answer : (C) Detergent solution washing
Description : In India the rails are manufactured by A. Open hearth process B. Duplex process C. Both A & B D. None of These
Last Answer : C [Both A & B]
Description : Softer variety of steel may be obtained by (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth
Last Answer : Answer: Option C
Description : The steel which contains fissures and cavities, is manufactured by (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth process
Last Answer : Answer: Option A
Description : Pick up the correct statement from the following: (A) Steel produced by open hearth process is milder than that obtained by the Bessemer process (B) Engineers prefer open hearth steel ... is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel
Description : The process of manufacturing steel by heating short lengths of wrought iron bars mixed with charcoal in fire clay crucibles and collecting the molten iron into moulds, is known as (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth process
Last Answer : Answer: Option B
Description : The process of decarbonising the pig iron completely and then adding proper percentage of carbon for manufacturing steel, is called (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth process