Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : Compound A is extracted from a solution of A + B into a pure solvent S. A Co-current unit is used for the liquid-liquid extraction. The inlet rate of the solution containing A is 200 moles of B/hr.m2 and the ... extraction achieved in the unit is (A) 25% (B) 50% (C) 70% (D) 90%
Last Answer : (B) 50%
Description : What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C
Last Answer : (B) Kcal/hr.m.°C
Description : Unit of mass velocity is (A) kg/hr (B) kg/m2 . hr (C) kg/m2 (D) kg/m3 . hr
Last Answer : (B) kg/m2 . hr
Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating
Last Answer : (A) Cold rolled steel coil annealing
Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola
Last Answer : (B) Reheating furnace
Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)
Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace
Last Answer : (C) Tunnel kiln
Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating
Last Answer : (B) Underfired
Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace
Last Answer : (B) Muffle furnace
Description : Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80
Last Answer : (B) 20
Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace
Last Answer : (A) By-product coke oven
Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these
Last Answer : (A) Soaking pit
Description : Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola
Last Answer : (C) Cupola
Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth
Last Answer : (A) Walking beam
Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ
Last Answer : (A) 3.6 AVS.ρ
Description : Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above
Last Answer : Answer: Option D
Description : One ton of refrigeration capacity is equivalent to the heat removal rate of (A) 50 kcal/hr (B) 200 BTU/hr (C) 200 BTU/minute
Last Answer : (C) 200 BTU/minute
Description : The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr. (A) 100 (B) 200 (C) 1000 (D) 2000
Last Answer : (B) 200
Description : Yield of blast furnace gas is about __________ Nm3 /ton of pig iron. (A) 300 (B) 2000 (C) 5000 (D) 10000
Last Answer : (B) 2000
Description : The usual energy consumption in electric arc furnace steel making is __________ KWh/ton of steel. (A) 60 - 100 (B) 400 - 700 (C) 1200 -1500 (D) 2000 - 2300
Last Answer : (B) 400 - 700
Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high
Last Answer : (B) Supersaturated
Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F
Last Answer : (C) 50 -100 BTU/hr. ft. 2°F
Description : Pick out the wrong statement: (A) With change in temperature, the radiant energy emitted by a black body remains unchanged (B) Absorptivity of a body approaches unity in case of diffuse reflection (C) Absorptivity of ... unity (D) Value of Stefan-Boltzmann constant is 4.876 10 -8 KCal/m2 .hr.°K4
Last Answer : (A) With change in temperature, the radiant energy emitted by a black body remains unchanged
Description : A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these
Last Answer : (B) 4.88 kcal/hr. m. 2°C
Description : Water filtration rate in a rapid sand filter ranges from __________ kilolitres/m2 /hr. (A) 0.1 to 1 (B) 3 to 6 (C) 10 to 15 (D) 15 to 20
Last Answer : (B) 3 to 6
Description : Water filtration rate in a slow sand filter ranges from __________ litres/m2 /hr. (A) 10 to 20 (B) 100 to 200 (C) 1500 to 2500 (D) 4000 to 5000
Last Answer : (B) 100 to 200
Description : A truck of mass 5 ton is travelling on a horizontal road with 36 km hr^-1 stops on travelling 1 km after its engine fails suddenly.
Last Answer : A truck of mass 5 ton is travelling on a horizontal road with 36 km hr-1 stops on travelling ... similar distance same how much will the fraction be?
Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : The radiation heat flux from a heating element at a temperature of 800°C, in a furnace maintained at 300°C is 8 kW/m2 . The flux, when the element temperature is increased to 1000°C for the same furnace temperature is (A) 11.2 kW/m2 (B) 12.0 kW/m2 (C) 14.6 kW/m2 (D) 16.5 kW/m
Last Answer : (D) 16.5 kW/m2
Description : Which is not accomplished in an underfired furnace? (A) Increase in heating capacity/m2 of floor space (B) Elimination of cold spot at the bottom of the charge (C) Reduction in the temperature of furnace gases (D) Protection of the periphery of the charge from excessive radiation
Last Answer : (A) Increase in heating capacity/m2 of floor space
Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )
Last Answer : a) Specific Energy Consumption of Induction Melting Furnace Molten Steel Production from the Induction melting furnace per day = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE = 655864000/107 = 65.586 ToE
Description : Normal values of overflow rate for plain sedimentation tank using coagulants, is (A) 750 to 1000 litres/hr/m2 (B) 1000 to 1250 litres/hr/m2 (C) 1250 to 1500 litres/hr/m2 (D) 1500 litres/hr/m
Last Answer : (B) 1000 to 1250 litres/hr/m2
Description : Normal values of overflow rate for sedimentation tanks using coagulants in litres/hr/m2 , generally range between (A) 250 to 500 (B) 500 to 750 (C) 750 to 1000 (D) 1000 to 1250
Last Answer : (D) 1000 to 1250
Description : Normal values of overflow rate for plain sedimentation tanks in litres/hr/m2 , generally range between (A) 100 to 250 (B) 250 to 500 (C) 500 to 750 (D) 750 to 1000
Last Answer : (C) 500 to 750
Description : Normal values of overflow rate for plain sedimentation tank, is (A) 250 to 500 litres/hr/m2 (B) 500 to 750 litres/hr/m2 (C) 750 to 1000 litres/hr/m2 (D) 1000 to 1250 litres/hr/m
Last Answer : (B) 500 to 750 litres/hr/m
Description : The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800
Last Answer : (A) 500
Description : It takes 0.4 hrs to drive from the garage to the head of the route, 0.4 hrs to drive between the route head and disposal site and 0.25 hrs to return from the disposal site. It takes 0.2 hrs to offload a truck at the ... loading time as 30 minutes. (a) 4.15 hrs (b) 4.25 hrs (c) 4.75 hrs (d) 4.85 hrs
Last Answer : (a) 4.15 hrs
Description : Specific heating capacity of a furnace is expressed as (A) Weight heated/hr (B) Weight heated/furnace volume (C) Weight heated/hr/furnace volume (D) None of these
Last Answer : (C) Weight heated/hr/furnace volume
Description : Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these
Last Answer : (A) kcal/hr/m3 combustion space
Description : The energy required per unit mass to grind limestone particles of very large size to 100 μm is 12.7 kWh/ton. An estimate (using Bond's law) of the energy to grind the particles from a very large size to 50 μm is (A) 6.35 kWh/ton (B) 9.0 kWh/ton (C) 18 kWh/ton (D) 25.4 kWh/ton
Last Answer : (C) 18 kWh/ton
Description : Mercury electrolytic cells are preferred over diaphragm electrolytic cell (for production of caustic soda), as it (A) Has larger production capacity per unit cell (B) Consumes less power per ton of Cl2 produced (C) Produces high purity (70%) caustic soda directly (D) All (A), (B) and (C)
Description : LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%) (D) All (A), (B) and (C)
Description : Maximum sulphur percentage in low sulphur heavy stock (LSHS) furnace oil is about (A) 0.1 (B) 1 (C) 2.5 (D) 3.5
Last Answer : (B) 1
Description : The rate of scaling of furnace stock depends upon the (A) Temperature (B) Time (C) Nature of atmosphere (D) All (A), (B) and (C)
Description : A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these
Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock
Last Answer : (A) Type of fuels viz. solid, liquid or gaseous