There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance.

a) True

b) False
by

1 Answer

Answer :

b) False
by

Related questions

Fatigue failure is time dependent failure. a) True b) False

Description : Fatigue failure is time dependent failure. a) True b) False

Last Answer : a) True

Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Description : Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Last Answer : (C) Creep

Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does not occur (C) Initiation of crack occurs on the surface of the machine part (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Description : Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does ... (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Last Answer : Option B

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Last Answer : (a) True

A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False

Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False

Last Answer : a) True

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Last Answer : b) Fatigue

Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal of load c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Last Answer : a) Ability of material to absorb energy when deformed elastically

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Last Answer : Option C

The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Last Answer : Ductile

Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Last Answer : (b) False

Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Last Answer : (b) False

Stribeck equation gives dynamic load capacity of the bearing. a) True b) False

Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False

Last Answer : b) False

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation

Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation

Last Answer : b) Plasticity

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Last Answer : (a) stick-slip

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Description : Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Last Answer : a) Stick-slip

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Description : The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Last Answer : (a) higher

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Last Answer : b) 2

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Last Answer : (D) All of the above

Which of the following is not true for cast iron flywheels? a) Excellent damping b) Cheap c) Given complex shape d) Sudden failure

Description : Which of the following is not true for cast iron flywheels? a) Excellent damping b) Cheap c) Given complex shape d) Sudden failure

Last Answer : d) Sudden failure

Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when (A) Strain rate is increased (B) Grain size is increased (C) Prior cold deformation is increased (D) Not affected by any of the above parameters

Description : Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when (A) Strain rate is increased (B) Grain size is increased (C) Prior cold deformation is increased (D) Not affected by any of the above parameters

Last Answer : (A) Strain rate is increased

Do you think scientists will be able to predict an earthquake more precisely and give people several hours advance warning?

Description : Do you think scientists will be able to predict an earthquake more precisely and give people several hours advance warning?

Last Answer : I would hope so, but I'm not exactly counting on it. I'm no scientist so I'm not sure how close the scientific community is to a breakthrough in plate techtonics research, but I would think with ... the world, this kind of research might be cut back a little bit in favor of more pressing needs.

Mark the correct option a) Prior permission is required to join Bharat sevak samaj b) Participation of Govt servants in the Indo-Foreign cultural organizations to be avoided c) Mere intimation sufficient to join samyukta sadachar samiti d) Prior permission necessary to join foreign language classes conducted by Indo- foreign cultural organizations. e) All the above

Description : Mark the correct option a) Prior permission is required to join Bharat sevak samaj b) Participation of Govt servants in the Indo-Foreign cultural organizations to be avoided c) Mere intimation ... to join foreign language classes conducted by Indo- foreign cultural organizations. e) All the above

Last Answer : e) All the above