Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Lead pipe is
(A) Especially resistant to solutions containing H2SO4
(B) Usually joined by burning (e.g. by melting to adjacent pieces with a
torch)
(C) Having very low elastic limit resulting in permanent deformation from
either mechanical or thermal strain
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C
by

Related questions

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

A hollow circular pipe with non-reflective inner surface is cut into 5 pieces and arranged as shown in the figure below. If it is illuminated from below using a torch as shown in the figure, what would be the profile of the light falling on the sheet kept above?

Description : A hollow circular pipe with non-reflective inner surface is cut into 5 pieces and arranged as shown in the figure below. If it is illuminated from below using a torch as shown in the figure, what would be the profile of the light falling on the sheet kept above?

Last Answer : A

All materials obey Hooke's law within elastic limit. When elastic limit is reached, the tensile strain (A) Increases very quickly (B) Decreases very quickly (C) Increases in proportion to stress (D) Decreases in proportion to stress

Description : All materials obey Hooke's law within elastic limit. When elastic limit is reached, the tensile strain (A) Increases very quickly (B) Decreases very quickly (C) Increases in proportion to stress (D) Decreases in proportion to stress

Last Answer : (A) Increases very quickly

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25

Description : cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25

Last Answer : Option C

Which of the following low melting alloy containing bismuth and lead is used for electric fuse? (A) Wood's metal (B) Babbitt metal (C) Monel metal (D) Duralumin

Description : Which of the following low melting alloy containing bismuth and lead is used for electric fuse? (A) Wood's metal (B) Babbitt metal (C) Monel metal (D) Duralumin

Last Answer : Option A

Lead pipes are not safe for carrying drinking water because water containing dissolved oxygen attacks lead thereby forming poisonous Pb (OH)2 . Lead pipes are readily corroded by (A) Dilute HCI (B) Acetic acid (C) Concentrated H2SO4 (D) None of these

Description : Lead pipes are not safe for carrying drinking water because water containing dissolved oxygen attacks lead thereby forming poisonous Pb (OH)2 . Lead pipes are readily corroded by (A) Dilute HCI (B) Acetic acid (C) Concentrated H2SO4 (D) None of these

Last Answer : (B) Acetic acid

Lead pipes are not safe for carrying drinking water, because water, containing dissolved oxygen attacks lead thereby forming poisonous Pb(OH)2 . Lead pipes are readily corroded by (A) Dilute HCl (B) Acetic acid (C) Concentrated H2SO4 (D) None of these

Description : Lead pipes are not safe for carrying drinking water, because water, containing dissolved oxygen attacks lead thereby forming poisonous Pb(OH)2 . Lead pipes are readily corroded by (A) Dilute HCl (B) Acetic acid (C) Concentrated H2SO4 (D) None of these

Last Answer : (B) Acetic acid

The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Last Answer : (b) Proportional Limit

Pick out the wrong statement. (A) Low intensity explosives are also called propellants, whereas high intensity explosive are called detonators (B) Gun powder comprises of 75% salt petre, 15% charcoal and 10% sulphur (C) Lead azide is a popular military explosive (D) TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

Description : Pick out the wrong statement. (A) Low intensity explosives are also called propellants, whereas high intensity explosive are called detonators (B) Gun powder comprises of 75% salt petre, 15% charcoal ... TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

Last Answer : (D) TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Description : What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Last Answer : (3) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.

What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Description : What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Last Answer : (4) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.

Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None

Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None

Last Answer : (c) Thirdly Maximum Principal stress theory

Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Last Answer : (d) None

Total strain energy theory for the failure of a material at elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory

Description : Total strain energy theory for the failure of a material at elastic limit, is known  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Haig's theory 

Last Answer : (D) Haig's theory 

Shear strain energy theory for the failure of a material at elastic limit, is due to (A) Rankine (B) Guest or Trecas (C) St. Venant (D) Von Mises

Description : Shear strain energy theory for the failure of a material at elastic limit, is due to  (A) Rankine  (B) Guest or Trecas  (C) St. Venant  (D) Von Mises

Last Answer : (D) Von Mises

Maximum strain theory for the failure of a material at the elastic limit, is known as (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory

Description : Maximum strain theory for the failure of a material at the elastic limit, is known as  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Haig's theory 

Last Answer : (B) St. Venant's theory

As the elastic limit reaches, tensile strain (A) Increases more rapidly (B) Decreases more rapidly (C) Increases in proportion to the stress (D) Decreases in proportion to the stress

Description : As the elastic limit reaches, tensile strain (A) Increases more rapidly (B) Decreases more rapidly (C) Increases in proportion to the stress (D) Decreases in proportion to the stress

Last Answer : (A) Increases more rapidly

Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength

Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Description : Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Last Answer : (A) Good mechanical strength

. A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Description : . A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Last Answer : (A) Newtonian

Consider the following statements: 1. Failure occurs beyond elastic limit 2. Rupture takes place immediately after elastic limit 3. Permanent set occurs beyond elastic limit Which of these are considered in the theories of failure? (a) 1, 2 and 3 (b) 1 and 3 only (c) 2 and 3 only d) 1 and 2 only

Description : Consider the following statements: 1. Failure occurs beyond elastic limit 2. Rupture takes place immediately after elastic limit 3. Permanent set occurs beyond elastic limit Which of these are considered in the theories of failure? (a) 1, 2 and 3 (b) 1 and 3 only (c) 2 and 3 only d) 1 and 2 only

Last Answer : d) 1 and 2 only

When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Last Answer : d) Plasticity

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco-elastic material, stress-strain relation is dependent on time (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Last Answer : (D) All the above

Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when (A) Strain rate is increased (B) Grain size is increased (C) Prior cold deformation is increased (D) Not affected by any of the above parameters

Description : Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when (A) Strain rate is increased (B) Grain size is increased (C) Prior cold deformation is increased (D) Not affected by any of the above parameters

Last Answer : (A) Strain rate is increased

Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Description : Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Last Answer : (D) Plastic

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just next to pipe (i.e., inside) (B) The better insulating material should be put outside (C) Either of the insulating material could be put on either side (D) Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)

Description : A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just ... to which insulating material is to be put inside (i.e., just next to the pipe)

Last Answer : (A) The better insulation material should be put just next to pipe (i.e., inside)

__________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Description : __________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Last Answer : (A) Pyrex

Is a propane "ice melt" torch effective for melting ice on a driveway?

Description : Is a propane "ice melt" torch effective for melting ice on a driveway?

Last Answer : No. But..I HAVE hooked up the garden hose to the hot water outlet in the garage that my washing machine hooks up to, and have hosed down icy areas with hot water to melt the ice. ;-)

Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process? (A) Galvanising (B) Tinning (C) Sherardizing (D) None of these

Description : Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process? (A) Galvanising (B) Tinning (C) Sherardizing (D) None of these

Last Answer : (C) Sherardizing

Nylon-6 as compared to nylon-66 is (A) Harder (B) More abrasion resistant (C) Having higher melting point (D) None of these

Description : Nylon-6 as compared to nylon-66 is (A) Harder (B) More abrasion resistant (C) Having higher melting point (D) None of these

Last Answer : (D) None of these

A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Description : A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Last Answer : (A) More corrosion resistant

A material capable of undergoing large permanent deformation, when subjected to compression is termed as (A) Malleable (B) Ductile (C) Brittle (D) None of these

Description : A material capable of undergoing large permanent deformation, when subjected to compression is termed as (A) Malleable (B) Ductile (C) Brittle (D) None of these

Last Answer : (A) Malleable

. A material capable of undergoing large permanent deformation, when subjected to tension is termed as (A) Friable (B) Ductile (C) Brittle (D) None of these

Description : . A material capable of undergoing large permanent deformation, when subjected to tension is termed as (A) Friable (B) Ductile (C) Brittle (D) None of these

Last Answer : (B) Ductile

The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Description : The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Last Answer : (B) Flexibility

03. A fluid whose viscosity changes with the rate of deformation or shear strain is known as Non￾Newtonian fluid. A) True B) False

Description : 03. A fluid whose viscosity changes with the rate of deformation or shear strain is known as Non￾Newtonian fluid. A) True B) False

Last Answer : A

A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Description : A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Last Answer : Answer: Option C

The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Description : The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Last Answer : a) Strain

The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these

Description : The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these

Last Answer : (a) Strain

Is it true Elastic deformation occurs when a material deforms as stress is applied?

Description : Is it true Elastic deformation occurs when a material deforms as stress is applied?

Last Answer : Yes

Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Description : Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Last Answer : ductile substances

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Description : A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Last Answer : (A) Plastic

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C