Handling of ashes and similar materials can be done best by a __________ conveyor. (A) Flight (B) Drag or slat (C) Belt (D) Ribbon

Handling of ashes and similar materials can be done best by a
__________ conveyor.
(A) Flight
(B) Drag or slat
(C) Belt
(D) Ribbon
by

1 Answer

Answer :

(B) Drag or slat
by

Related questions

Short distance transportation of grain, gravel, sand, ash, asphalt etc. is done by using a __________ conveyor. (A) Flight (B) Slat or drag (C) Ribbon (D) Screw

Description : Short distance transportation of grain, gravel, sand, ash, asphalt etc. is done by using a __________ conveyor. (A) Flight (B) Slat or drag (C) Ribbon (D) Screw

Last Answer : (D) Screw

Gummy & sticky materials like molasses, sugar etc. are besttransported/handled by using a __________ conveyor.(A) Drag(B) Ribbon(C) Screw(D) Slat

Description : Gummy & sticky materials like molasses, sugar etc. are besttransported/handled by using a __________ conveyor. (A) Drag (B) Ribbon (C) Screw (D) Slat

Last Answer : (B) Ribbon

__________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Description : __________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Last Answer : (A) Flight

Which of the following mechanical conveyors does not come under the division ‘scrapers’? (A) Ribbon conveyor (B) Flight conveyor (C) Bucket elevators (D) Drag conveyor

Description : Which of the following mechanical conveyors does not come under the division ‘scrapers’? (A) Ribbon conveyor (B) Flight conveyor (C) Bucket elevators (D) Drag conveyor

Last Answer : (C) Bucket elevators

Which of the following material handling equipments is not suitable for moving materials in varying paths? (A) Hand trolley (B) Belt conveyor (C) Crane (D) Truck

Description : Which of the following material handling equipments is not suitable for moving materials in varying paths? (A) Hand trolley (B) Belt conveyor (C) Crane (D) Truck

Last Answer : (B) Belt conveyor

Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Description : Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Last Answer : (C) Flight conveyor

Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Description : Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Last Answer : (A) Apron

__________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Last Answer : (B) Belt

Dry powdery solid materials are transported by a __________ conveyor. (A) Belt (B) Bucket (C) Screw (D) None of these

Description : Dry powdery solid materials are transported by a __________ conveyor. (A) Belt (B) Bucket (C) Screw (D) None of these

Last Answer : (C) Screw

A belt conveyor used for the transportation of materials can (A) Run upto 1 km (B) Travel at a speed upto 300 metres/minute (C) Handle materials upto 5000 tons/hr (D) All (A), (B) and (C)

Description : A belt conveyor used for the transportation of materials can (A) Run upto 1 km (B) Travel at a speed upto 300 metres/minute (C) Handle materials upto 5000 tons/hr (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The capacity of a belt conveyor depends upon two factors. If one is the cross-section of the load, the other is the __________ of the belt. (A) Speed (B) Thickness (C) Length (D) None of these

Description : The capacity of a belt conveyor depends upon two factors. If one is the cross-section of the load, the other is the __________ of the belt. (A) Speed (B) Thickness (C) Length (D) None of these

Last Answer : (A) Speed

Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Description : Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Description : For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Last Answer : (B) Pneumatic

Vertical transportation of materials can be done by a/an (A) Apron conveyor (B) Pneumatic conveyor (C) Bucket elevator (D) Both (B) & (C)

Description : Vertical transportation of materials can be done by a/an (A) Apron conveyor (B) Pneumatic conveyor (C) Bucket elevator (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

The maximum slope of a belt conveyor can be (A) 15° (B) 30° (C) 45° (D) 60

Description : The maximum slope of a belt conveyor can be (A) 15° (B) 30° (C) 45° (D) 60

Last Answer : (B) 30°

The most suitable equipment for the transportation of 200 mesh size particles is a (A) Bucket elevator (B) Pneumatic conveyor (C) Screw conveyor (D) Belt conveyor

Description : The most suitable equipment for the transportation of 200 mesh size particles is a (A) Bucket elevator (B) Pneumatic conveyor (C) Screw conveyor (D) Belt conveyor

Last Answer : (B) Pneumatic conveyor

Which is the most suitable conveyor for transportation of sticky material? (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Pneumatic conveyo

Description : Which is the most suitable conveyor for transportation of sticky material? (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Pneumatic conveyo

Last Answer : (C) Screw conveyor

For transporting pasty material, one will use a/an (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Bucket elevator

Description : For transporting pasty material, one will use a/an (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Bucket elevator

Last Answer : (C) Screw conveyor

Which of the following mechanical conveyors does not come under the division ‘carriers’? (A) Belt conveyor (B) Bucket elevator (C) Screw conveyor

Description : Which of the following mechanical conveyors does not come under the division ‘carriers’? (A) Belt conveyor (B) Bucket elevator (C) Screw conveyor

Last Answer : (C) Screw conveyor

Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise of conveyor belt system is reduced by using urethane coated cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Description : Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise ... cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

From the following which material handling equipment is used in Robot centered layout of FMS a.Industrial Robot b.Conveyor systems c.Rail guided vehicle system d.None of the above

Description : From the following which material handling equipment is used in Robot centered layout of FMS a.Industrial Robot b.Conveyor systems c.Rail guided vehicle system d.None of the above

Last Answer : a.Industrial Robot

From the following which material handling equipment is used in ladder layout of FMS a.Conveyor systems b.AGVS c.Both A & B d.None of the above

Description : From the following which material handling equipment is used in ladder layout of FMS a.Conveyor systems b.AGVS c.Both A & B d.None of the above

Last Answer : c.Both A & B

Where can I buy a belt conveyor system?

Description : Where can I buy a belt conveyor system?

Last Answer : There are several different sites online where you can purchase a conveyor belt system. One such site is conveyorbelts.com. A wide selection is offered.

What type of bearing will you recommend for use in the conveyor belt roller? (a) Ball-bearing (b) Roller bearing (c) Magnetic bearing (d) None of the mentioned

Description : What type of bearing will you recommend for use in the conveyor belt roller? (a) Ball-bearing (b) Roller bearing (c) Magnetic bearing (d) None of the mentioned

Last Answer : (b) Roller bearing

are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.

Develop a ladder diagram for to control conveyor belt motor equipped with the: (i) Counter of item. (ii) Start & Stop functions. (iii) Change of direction function.

Description : Develop a ladder diagram for to control conveyor belt motor equipped with the: (i) Counter of item. (ii) Start & Stop functions. (iii) Change of direction function.

Last Answer : Forward: Reverse:

Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Last Answer : (A) 3.6 W.D.V.ρ

Mechanical conveyors which push the material along an endless trough or tube are called scrappers. Which of the following conveying equipments comes under the category of ‘scrappers’? (A) Bucket conveyor (B) Flight conveyor (C) Screw conveyor (D) Both (B) and (C)

Description : Mechanical conveyors which push the material along an endless trough or tube are called scrappers. Which of the following conveying equipments comes under the category of ‘scrappers’? (A) Bucket conveyor (B) Flight conveyor (C) Screw conveyor (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Raw materials are charged in the iron blast furnace using (A) Bucket elevator (B) Skip hoist (C) Screw conveyor (D) None of these

Description : Raw materials are charged in the iron blast furnace using (A) Bucket elevator (B) Skip hoist (C) Screw conveyor (D) None of these

Last Answer : (B) Skip hoist

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal c. Thrust is greater than drag and lift is greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Description : Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal ... greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Last Answer : b. These forces are equal

__________ adds time and place utility to a product by moving it from where it is made to where it is purchased and used. A)Warehousing B)Containerisation C)Distribution D)Materials handling E)Transportation

Description : __________ adds time and place utility to a product by moving it from where it is made to where it is purchased and used. A)Warehousing B)Containerisation C)Distribution D)Materials handling E)Transportation

Last Answer : E)Transportation

Air-tech management learns that last month's production run of heaters is defective and announces a recall of the specific models produced. To handle the large number of products it expects to receive for replacement, Air -tech will probably need to add a __________ to its distribution network. A)distribution centre B)private warehouse C)dispatching shipment system D)public warehouse E)materials handling system

Description : Air-tech management learns that last month's production run of heaters is defective and announces a recall of the specific models produced. To handle the large number of products ... distribution centre B)private warehouse C)dispatching shipment system D)public warehouse E)materials handling system

Last Answer : D)public warehouse

Order processing, inventory management, materials handling, warehousing, and transportation are __________ activities. A)wholesaling B)retailing C)physical distribution D)channel management

Description : Order processing, inventory management, materials handling, warehousing, and transportation are __________ activities. A)wholesaling B)retailing C)physical distribution D)channel management

Last Answer : C)physical distribution

Refractory bricks are usually dried in a __________ dryer. (A) Tray (B) Tunnel (C) Conveyor (D) Festoon

Description : Refractory bricks are usually dried in a __________ dryer. (A) Tray (B) Tunnel (C) Conveyor (D) Festoon

Last Answer : (B) Tunnel

Dryer widely used in a textile industry is __________ dryer. (A) Festoon (B) Cylinder (C) Conveyor (D) Tunnel

Description : Dryer widely used in a textile industry is __________ dryer. (A) Festoon (B) Cylinder (C) Conveyor (D) Tunnel

Last Answer : (C) Conveyor

In paper industry, paper is dried in a __________ dryer. (A) Tunnel (B) Heated cylinder (C) Conveyor (D) Festoon

Description : In paper industry, paper is dried in a __________ dryer. (A) Tunnel (B) Heated cylinder (C) Conveyor (D) Festoon

Last Answer : (B) Heated cylinder

During a general briefing at the pre-flight stage, the captain should emphasize: a. The complete delegation of all duties b. The importance of crew coordination c. The priority of departing on schedule d. The avoidance of inadequate handling of controls

Description : During a general briefing at the pre-flight stage, the captain should emphasize: a. The complete delegation of all duties b. The importance of crew coordination c. The priority of departing on schedule d. The avoidance of inadequate handling of controls

Last Answer : b. The importance of crew coordination

During a general briefing at the pre-flight stage, the captain should emphasize: a. The complete delegation of all duties b. The importance of crew coordination c. The priority of departing on schedule d. The avoidance of inadequate handling of controls

Description : During a general briefing at the pre-flight stage, the captain should emphasize: a. The complete delegation of all duties b. The importance of crew coordination c. The priority of departing on schedule d. The avoidance of inadequate handling of controls

Last Answer : b. The importance of crew coordination

__________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Description : __________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Last Answer : (B) Dry powders

__________ mixer is used for devulcanisation of rubber scrap & making water dispersion & rubber solution.(A) Tumbler (B) Banbury (C) Muller (D) Ribbon blender

Description : __________ mixer is used for devulcanisation of rubber scrap & making water dispersion & rubber solution. (A) Tumbler (B) Banbury (C) Muller (D) Ribbon blender

Last Answer : (B) Banbury

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Vibrating screens are used for handling large tonnages of materials. The vibrating motion is imparted to the screening surface by means of (A) Electromagnets (B) Cams or eccentric shafts (C) Unbalanced flywheels (D) Either (A), (B) or (C)

Description : Vibrating screens are used for handling large tonnages of materials. The vibrating motion is imparted to the screening surface by means of (A) Electromagnets (B) Cams or eccentric shafts (C) Unbalanced flywheels (D) Either (A), (B) or (C)

Last Answer : (D) Either (A), (B) or (C)

Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Description : Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Last Answer : (D) Brass, cast iron, mild steel and tin

High pressure at the bottom of a distillation tower handling heat sensitive materials results in (A) Thermal decomposition of bottoms (B) Increased relative volatility (C) Erosion of the tower (D) Very efficient operation

Description : High pressure at the bottom of a distillation tower handling heat sensitive materials results in (A) Thermal decomposition of bottoms (B) Increased relative volatility (C) Erosion of the tower (D) Very efficient operation

Last Answer : (A) Thermal decomposition of bottoms

A compact estimate about the amount of materials handling between various work stations is obtained from the (A) Gantt chart (B) Bin chart (C) String diagram (D) Travel chart

Description : A compact estimate about the amount of materials handling between various work stations is obtained from the (A) Gantt chart (B) Bin chart (C) String diagram (D) Travel chart

Last Answer : (D) Travel chart

The slat type mold board is used in a) Sticky soil b) Hard soil c) Loose soil d) Stoney and trashy soil Ans. a

Description : The slat type mold board is used in a) Sticky soil b) Hard soil c) Loose soil d) Stoney and trashy soil Ans. a

Last Answer : ans a

This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above

Description : This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above

Last Answer : Ans- b. Sod or breaker

is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Description : is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Last Answer :  Disc harrow

have gaps between the slats. a) Share b) Soil c) Slat type d) None

Description : have gaps between the slats. a) Share b) Soil c) Slat type d) None

Last Answer : Slat type