Draw a neat labeled sketch of the following: i) Aqueduct ii) Super passage iii)Level crossing

Draw a neat labeled sketch of the following: i) Aqueduct ii) Super passage iii)Level crossing
by

1 Answer

Answer :

i) Aqueduct 

Image 1113.jpg

ii) Super passage

Image 1116.jpg

Iii ) Level Crossing

Image 1119.jpg

by

Related questions

The drainage water intercepting the canal can be disposed of by passing the canal below the drainage in (A) Aqueduct and syphon aqueduct (B) Aqueduct and super passage (C) Super passage and canal syphon (D) Level crossing

Description : The drainage water intercepting the canal can be disposed of by passing the canal below the drainage in (A) Aqueduct and syphon aqueduct (B) Aqueduct and super passage (C) Super passage and canal syphon (D) Level crossing

Last Answer : Answer: Option C

Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of these statements are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Description : Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of ... are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Last Answer : d) 1 and 3 only

The aqueduct or super-passage type of works are generally used when (A) High flood drainage discharge is small (B) High flood drainage discharge is large and short lived (C) High flood drainage discharge is large and continues for a long time (D) None of the above

Description : The aqueduct or super-passage type of works are generally used when (A) High flood drainage discharge is small (B) High flood drainage discharge is large and short lived (C) High flood drainage discharge is large and continues for a long time (D) None of the above

Last Answer : Answer: Option A

Draw neat labeled sketch of ply press.

Description : Draw neat labeled sketch of ply press.

Last Answer : sketch of ply press

Draw a neat labeled sketch of 30m chain.

Description : Draw a neat labeled sketch of 30m chain.

Last Answer : neat labeled sketch of 30m chain

Draw neat and labeled sketch of three pass packages type boiler.

Description : Draw neat and labeled sketch of three pass packages type boiler. 

Last Answer : Each set of tubes that hot combustion flue gas travels through before making a turn within the boiler, is considered a "pass." A 3-pass fire tube boiler design consists of three sets of ... design that allows more heat transfer time to deliver the same or higher efficiency rating. 

Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line

Description : Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

Last Answer : i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

When the railway crosses a deep vally without perinial water,it is called……. a)Aqueduct * b)Cause way c)Via-duct d)River crossing

Description : When the railway crosses a deep vally without perinial water,it is called……. a)Aqueduct * b)Cause way c)Via-duct d)River crossing

Last Answer : a)Aqueduct *

Explain the requirements of good formwork with names and materials proposed for beam of size 300 X 450 mm with neat labeled sketch.

Description : Explain the requirements of good formwork with names and materials proposed for beam of size 300 X 450 mm with neat labeled sketch.  

Last Answer : Requirements of good formwork:- 1. It should be adequately strong to withstand an extensive variety of dead and live loads. For instance, self-weight, weight of reinforcement, weight of wet concrete, loads of ... of concreting. 8. It should be lightweight. 9. It should be easy to remove.

Draw a labeled sketch of pump feed fuel supply system for petrol engine and state location and function of each component.

Description : Draw a labeled sketch of pump feed fuel supply system for petrol engine and state location and function of each component.

Last Answer : The pump feed system is shown in the figure above. Fuel tank is for storage of fuel located above the engine of two wheeler and in case of car located at backside of the car ... the tendency of forming vapor lock. The system provides the fuel requirement at various engine speeds efficiently. 

Draw labeled sketch of prismatic compass.

Description : Draw labeled sketch of prismatic compass.

Last Answer : Sketch of prismatic compass :

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Description : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Last Answer : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Description :  Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Last Answer : Labeled diagram of 3-phase electronic energy meter:

Draw neat labeled diagram of optical pyrometer.

Description : Draw neat labeled diagram of optical pyrometer.

Last Answer :  optical pyrometer

Draw neat labeled diagram of AC track circuit. Also give two advantages of AC track circuit.

Description : Draw neat labeled diagram of AC track circuit. Also give two advantages of AC track circuit.

Last Answer : AC Track Circuit:  Advantages of AC Track Circuit: 1. Free from effects of stray currents. 2. Track circuit is up to a long length of track in one section length up to 3km to 5 km. 3. Cheaper in costs as compared to DC track circuit. 4. Easy to install than DC track circuit. 

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

Draw a neat labeled diagram to show protective system for AC traction and give the function of each relay used in it.

Description : Draw a neat labeled diagram to show protective system for AC traction and give the function of each relay used in it. 

Last Answer : Protective system for AC traction:  Function Of Each Relay: For transformer -  Inverse time over current relay- as back up protection on primary (HV side) over current ... against faults near substation  Under voltage relay - protection against faults far away from substation

Draw a neat labeled diagram of Automatic Weight Tensioning and Temperature Compensation and give any two advantages of the same.

Description : Draw a neat labeled diagram of Automatic Weight Tensioning and Temperature Compensation and give any two advantages of the same.

Last Answer :  figure of automatic weight tensioning Advantages of automatic weight tensioning and temperature compensation:  Sparkless current collection at higher speeds.  OHE becomes more dynamically ... of unregulated OHE.  Because of fixed tension, fluctuations in the height are minimized

(i) state any two applications of I. C. Engine (ii) Draw a neat sketch of Two stroke petrol engine.

Description : (i) state any two applications of I. C. Engine (ii) Draw a neat sketch of Two stroke petrol engine.

Last Answer : Applications of I.C engine 1) In Automotive - i) Two stroke engine - Mopeds, Scooters. ii) Four stroke engine - Light vehicles, Heavy vehicles. 2) Marine Application - Ships, Boat 3) Locomotive s - ... handling system  (ii) Draw a neat sketch of Two stroke petrol engine. OR

(i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Description : (i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Last Answer : (i)   (ii) Sources of air leakage in condenser: i) Air leak through joints and packing. ii) Air also comes in condenser with the steam. iii) In jet condensers dissolved air in the cooling water enters the condenser. 

Explain the following terms of centrifugal governor with neat sketch: (i) Height of Governor (ii) Equilibrium Speed (iii) Sleeve Lift

Description : Explain the following terms of centrifugal governor with neat sketch: (i) Height of Governor (ii) Equilibrium Speed (iii) Sleeve Lift

Last Answer : Terms related with Governor: (i) Height of Governor: It is the vertical distance from the centre of the ball to a point where the axes of the arms (or arms produced) intersect on ... (iii) Sleeve Lift: It is the vertical distance which the sleeve travels due to change in equilibrium speed.

In a contour map, if contours are crossing each other, what will be nature of topography? Draw the sketch to support your answer.

Description : In a contour map, if contours are crossing each other, what will be nature of topography? Draw the sketch to support your answer.

Last Answer : If contours are crossing or intersecting each other, then there is overhanging cliff as shown in figure 1 below.

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.   

Draw a neat sketch of Electro-dialysis.

Description : Draw a neat sketch of Electro-dialysis.

Last Answer : Electro- dialysis:

Draw a neat sketch of cross-section of an exogenous tree and label the parts.

Description : Draw a neat sketch of cross-section of an exogenous tree and label the parts. 

Last Answer : Cross-section of an exogenous tree:

Draw the neat sketch of overhead valve operating mechanism and explain its working.

Description : Draw the neat sketch of overhead valve operating mechanism and explain its working.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the push ... close. A spring (attached to the valve) returns the valve to its seated position.   

Draw neat sketch of valve timing diagram for 4-stroke petrol engine & label it.

Description : Draw neat sketch of valve timing diagram for 4-stroke petrol engine & label it.

Last Answer : Figure: Valve timing diagram of 4 stroke SI engine  

Draw a neat lebelled sketch of optical square. Explain its working.

Description : Draw a neat lebelled sketch of optical square. Explain its working.

Last Answer : Working of optical square1. Optical square works on principle of optical square to set perpendicular offset 2. Keep ranging rods at point B and C as shown in fig. 3. Observe the ... matched each other point D can be marked on ground and distance CD is measured as perpendicular offset.

Draw a neat sketch of an arrow with dimensions.

Description : Draw a neat sketch of an arrow with dimensions.

Last Answer :  neat sketch of an arrow with dimensions

Draw a neat sketch of optical square. Explain its working.

Description : Draw a neat sketch of optical square. Explain its working.

Last Answer : Optical Square: Working: The optical square consists of circular box 50 mm in diameter, 12.5 mm in depth. The box has three slits as A,B, and C. bb' is horizon glass, half silvered i.e ... the point on the chain line where the offset can be dropped to meet point J as shown in fig.  

Draw a neat sketch of prismatic compass and label its component parts

Description : Draw a neat sketch of prismatic compass and label its component parts

Last Answer : Sketch of prismatic compass and label its component parts

Draw neat sketch of pre-combustion chamber and name its parts.

Description : Draw neat sketch of pre-combustion chamber and name its parts.

Last Answer : Fig. Pre-combustion chamber

Draw neat sketch to show TBI system of SI engine and name its parts.

Description : Draw neat sketch to show TBI system of SI engine and name its parts.

Last Answer : Draw neat sketch to show TBI system of SI engine and name its parts.

State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Description : State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Last Answer : 1) T Head Type Combustion chambers 2) L Head Type Combustion chambers 3) F- Head combustion chamber 4) Over head valve or I head combustion chamber 5) Hemispherical combustion chamber 6) Bathtub ... - Head combustion chamber 4) Over head valve or I head combustion chamber

Draw neat sketch of swirl type combustion chamber of IDI engine.

Description : Draw neat sketch of swirl type combustion chamber of IDI engine.

Last Answer : Fig. swirl type combustion chamber of IDI engine.

Define folds and draw neat sketch of a fold and label its different parts.

Description : Define folds and draw neat sketch of a fold and label its different parts. 

Last Answer : Fold: Folds may be defined as undulations or bends that are developed in the rock of the Earth’s crust, as a result of stresses (commonly lateral compression) To which these rocks have been subjected to, from time to time in the past history of the Earth.

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

Draw a neat sketch of simple curve showing all elements.

Description : Draw a neat sketch of simple curve showing all elements.

Last Answer : Simple curve

Draw neat sketch of simple circular curve and show notation there on.

Description : Draw neat sketch of simple circular curve and show notation there on.

Last Answer : Sketch of simple circular curve and show notation there on :

Draw a neat sketch of progressive die.

Description : Draw a neat sketch of progressive die. 

Last Answer : progressive die

Draw neat sketch showing various parts of die set.

Description : Draw neat sketch showing various parts of die set. 

Last Answer : Answer: 1. Stop 2.Sheet metal 3.Pilot 4.Blanking punch 5.Ram 6.Piercing punch 7.Stripper 8.die Fig. Progressive Die OR

Draw neat sketch of compound die, showing various parts of it.

Description : Draw neat sketch of compound die, showing various parts of it.

Last Answer : Answer:

Draw the neat sketch of fly press. Give the functions of important parts of it.

Description : Draw the neat sketch of fly press. Give the functions of important parts of it. 

Last Answer : Answer: OR Functions of important parts of Fly Press. 1. Ram : This is main operating part of the press which works directly during processing of a workpiece. Ram ... : A die is a specialized tool used in manufacturing industries to cut or shape material mostly using a press 

Draw a neat sketch of regenerative feed heating.

Description : Draw a neat sketch of regenerative feed heating.

Last Answer : Regenerative Feed Heating  

Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Last Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Draw a neat sketch of Ultrasonic flowmeter.

Description : Draw a neat sketch of Ultrasonic flowmeter. 

Last Answer : Diagram of ultrasonic flow meter (Time Difference Type ):

Draw neat sketch of Rotameter and explain its working principle.

Description : Draw neat sketch of Rotameter and explain its working principle.

Last Answer : Rotameter: - A variable-area flowmeter is one where the fluid must pass through a restriction whose area increases with flow rate. The height of the float is directly proportional to the flowrate ... on glass tube and the flow rate can be determined by direct observation of the metering tube  

Draw neat labelled sketch of Lamont boiler.

Description : Draw neat labelled sketch of Lamont boiler. 

Last Answer : Lamont boiler

Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Description : Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Last Answer : Draw a neat sketch showing RCC components of lintel with 1:20 scale.