Pick out the correct combination about the role of various additives used in polymers. (A) Plasticiser: increases the polymer strength (B) Heat stabiliser: increases the maximum service temperature (C) Fillers: Does not affect the property of polymer but increases its weight (D) Lubricants: increases the flexibility of polymers

Pick out the correct combination about the role of various additives
used in polymers.
(A) Plasticiser: increases the polymer strength
(B) Heat stabiliser: increases the maximum service temperature
(C) Fillers: Does not affect the property of polymer but increases its weight
(D) Lubricants: increases the flexibility of polymers
by

1 Answer

Answer :

Option C
by

Related questions

Plasticisers are high boiling liquids added to plastic polymers to impart toughness and flexibility at ordinary temperature. Which of the following is not a plasticiser? (A) Ethylene glycol (B) Stearic acid estors (C) Tricresyl phosphate (D) Esters of phthalic acid

Description : Plasticisers are high boiling liquids added to plastic polymers to impart toughness and flexibility at ordinary temperature. Which of the following is not a plasticiser? (A) Ethylene glycol (B) Stearic acid estors (C) Tricresyl phosphate (D) Esters of phthalic acid

Last Answer : (A) Ethylene glycol

Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to a very high temperature (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Description : Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to ... D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Last Answer : (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Description : Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Last Answer : (C) Flexibility

Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more aliphatic character are more soluble in aliphatic solvents, while those polymers having more aromatic character are more soluble in aromatic solvents (C) Swelling tendency or solubility of polymers in a particular solvent decreases with increase in molecular weight of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Description : Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more ... of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Last Answer : (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Addition of stabiliser during PVC manufacture is done to (A) Improve its impact strength (B) Improve its elasticity (C) Reduce the melt viscosity & glass transition temperature (D) Prevent its thermal degradation

Description : Addition of stabiliser during PVC manufacture is done to (A) Improve its impact strength (B) Improve its elasticity (C) Reduce the melt viscosity & glass transition temperature (D) Prevent its thermal degradation

Last Answer : (D) Prevent its thermal degradation

Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Description : Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Last Answer : (B) Softness & flexibility

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Description : Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Last Answer : Answer: Option D

. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Last Answer : (D) Hardness, rigidity & brittleness

Pick out the wrong statement. (A) Polymers made of only one monomer is called homopolymer (B) Polymers made of more than one monomer is called copolymer or mixed polymer (C) Vulcanised rubber is more elastic than natural rubber

Description : Pick out the wrong statement. (A) Polymers made of only one monomer is called homopolymer (B) Polymers made of more than one monomer is called copolymer or mixed polymer (C) Vulcanised rubber is more elastic than natural rubber

Last Answer : (A) Polymers made of only one monomer is called homopolyme

What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Description : What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Last Answer : amount of hydrogen bonding between different subunitsnumber of subunits in the polymer chainits greater tensile strengththe synthetic composure

Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter polymer melt to harden into filaments. Melt spinning is not used in case of the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Description : Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter ... the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Last Answer : (A) Acrylic

Fillers such as zinc oxide and carbon black are added to the crude natural rubber before vulcanisation in order to improve its (A) Elasticity (B) Strength (C) Plasticity (D) Weathering characteristics

Description : Fillers such as zinc oxide and carbon black are added to the crude natural rubber before vulcanisation in order to improve its (A) Elasticity (B) Strength (C) Plasticity (D) Weathering characteristics

Last Answer : (D) Weathering characteristics

What do you call a polymer without adding additives or blending with another ploymer?

Description : What do you call a polymer without adding additives or blending with another ploymer?

Last Answer : Need answer

Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Description : Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Last Answer : (A) Polymeric fibres are never produced by addition polymerisation

Which of the following is not a primary essential property of a fibre? a. Flexibility b. Tensile strength c. Absorbency d. Cohesiveness

Description : Which of the following is not a primary essential property of a fibre? a. Flexibility b. Tensile strength c. Absorbency d. Cohesiveness

Last Answer : c. Absorbency

Pick out the correct statement. (A) Higher is the temperature of the radiating body, higher is the wavelength of radiation (B) Logarithmic mean area is used for calculating the heat flow rate through a thick walled cylinder (C) The wavelength corresponding to maximum mono-chromatic emissive power increases with rise in temperature (D) Solid angle subtended by the finite surface at the radiating element is called the angle of incidence

Description : Pick out the correct statement. (A) Higher is the temperature of the radiating body, higher is the wavelength of radiation (B) Logarithmic mean area is used for calculating the heat flow rate ... ) Solid angle subtended by the finite surface at the radiating element is called the angle of incidence

Last Answer : (B) Logarithmic mean area is used for calculating the heat flow rate through a thick walled cylinder

Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or thermosetting (C) Branching in case of cross-linked polymers caused by small amount of impurities in bifunctional monomer formulation reduces its solubility and increases the softening point (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Description : Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or ... (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Last Answer : D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

In case of wet spinning of polymers, the polymer solution is forced through spinnerates into, a coagulating bath to give a filament form. Wet spinning is not used in case of the __________ fibres. (A) Viscose rayon (B) Acrylic (C) Polyvinyl acetate (D) Saturated polyeste

Description : In case of wet spinning of polymers, the polymer solution is forced through spinnerates into, a coagulating bath to give a filament form. Wet spinning is not used in case of the __________ fibres. (A) Viscose rayon (B) Acrylic (C) Polyvinyl acetate (D) Saturated polyeste

Last Answer : (D) Saturated polyeste

Which of the following polymers does not belong to the class of Polyacrylate polymer? (A) PMMA(B) Polyacrylonitrile(C) Poly Ethyl acrylate(D) None of these

Description : Which of the following polymers does not belong to the class of Polyacrylate polymer? (A) PMMA (B) Polyacrylonitrile (C) Poly Ethyl acrylate (D) None of these

Last Answer : (D) None of these

In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Description : In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament ... is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Last Answer : (B) PVC

Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Description : Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Last Answer : (C) Elastometric

Viscosity of a polymer solution or melt (A) Decreases with increase in molecular weight (B) Decreases with increase in temperature (C) Increases with increase in temperature (D) Does not vary with temperature rise

Description : Viscosity of a polymer solution or melt (A) Decreases with increase in molecular weight (B) Decreases with increase in temperature (C) Increases with increase in temperature (D) Does not vary with temperature rise

Last Answer : (C) Increases with increase in temperature

Polyvinyl chloride (PVC) (A) Is produced by Polycondensation reaction (B) Uses either emulsion or suspension polymerisation methods (C) Can be made thermosetting by adding a plasticiser (D) Softening temperature is 200°C

Description : Polyvinyl chloride (PVC) (A) Is produced by Polycondensation reaction (B) Uses either emulsion or suspension polymerisation methods (C) Can be made thermosetting by adding a plasticiser (D) Softening temperature is 200°C

Last Answer : (B) Uses either emulsion or suspension polymerisation methods

The best lubricants for a machine working at high temperature & load is (A) Grease (B) Solid lubricant (C) Animal oils (D) Mineral oils

Description : The best lubricants for a machine working at high temperature & load is (A) Grease (B) Solid lubricant (C) Animal oils (D) Mineral oils

Last Answer : Option B

Pick out the wrong statement. (A) Copper is the metal having the highest electronic conductivity (B) Hardenability & Weldability of metals are inversely related (C) Covalent bonding formed by sharing of electrons is present in all semiconductor materials (D) Glass transition temperature applies to 'polymers' but not to 'glasses'

Description : Pick out the wrong statement. (A) Copper is the metal having the highest electronic conductivity (B) Hardenability & Weldability of metals are inversely related (C) Covalent bonding formed by ... all semiconductor materials (D) Glass transition temperature applies to 'polymers' but not to 'glasses'

Last Answer : Option A

Are All Conductive Polymers, Conjugated Polymer?

Description : Are All Conductive Polymers, Conjugated Polymer?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

Classify the polymers as addition and condensation polymer— Nylon 6, Neoprene and PVC.

Description : Classify the polymers as addition and condensation polymer— Nylon 6, Neoprene and PVC.

Last Answer : Ans: Nylon 6 —Condensation polymer  Neoprene and PVC— Addition polymer.

What is the advantage of synthetic polymer over glass? OR Why is glass being replaced by synthetic polymers?

Description : What is the advantage of synthetic polymer over glass? OR Why is glass being replaced by synthetic polymers?

Last Answer : Glass is being replaced by light and transparent synthetic polymers like poly methyl metacrylate polymers. The advantages of polymers are that they are unbreakable, light and scratches on polymers can be removed by wiping with acetone.

Pick out the wrong statement about the smoking tendency of various hydrocarbon constituents of kerosene. (A) Smoking tendency of hydrocarbons increases in the order: paraffins → isoparaffins → naphthenes → aromatics (B) Smoking tendency of paraffins increases with decrease in its molecular weight

Description : Pick out the wrong statement about the smoking tendency of various hydrocarbon constituents of kerosene. (A) Smoking tendency of hydrocarbons increases in the order: paraffins → isoparaffins → naphthenes → aromatics (B) Smoking tendency of paraffins increases with decrease in its molecular weight

Last Answer : (B) Smoking tendency of paraffins increases with decrease in its molecular weight

A Zener diode is operated in the …… mode as a voltage stabiliser.

Last Answer : A Zener diode is operated in the Reverse bias around the knee of breakdown region mode as a voltage stabilizer.

Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Description : Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the ... in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Last Answer : (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity

What Designed to regulate temperature secrete lubricants and protect the body from harmful substances?

Description : What Designed to regulate temperature secrete lubricants and protect the body from harmful substances?

Last Answer : Epithelial tissues

. Pick out the wrong statement. (A) The eddy viscosity is a function of(B) The eddy viscosity is a fluid property(C) The viscosity of gas increases with increase in temperature(D) The viscosity of a liquid increases with decrease in temperature the type of turbulence involved

Description : . Pick out the wrong statement. (A) The eddy viscosity is a function of the type of turbulence involved (B) The eddy viscosity is a fluid property (C) The viscosity of gas increases with increase in temperature (D) The viscosity of a liquid increases with decrease in temperature

Last Answer : (B) The eddy viscosity is a fluid property

Pick out the correct statement. (A) Diffusivity decreases with increase in temperature (B) Diffusivity increases with increase in molecular weight (C) Diffusivity increases with the size of the individual molecule (D) None of these

Description : Pick out the correct statement. (A) Diffusivity decreases with increase in temperature (B) Diffusivity increases with increase in molecular weight (C) Diffusivity increases with the size of the individual molecule (D) None of these

Last Answer : (D) None of these

Alkyd resin cannot be used for making (A) Plasticiser (B) Paint & varnish (C) Fibres (D) Film forming materials

Description : Alkyd resin cannot be used for making (A) Plasticiser (B) Paint & varnish (C) Fibres (D) Film forming materials

Last Answer : (C) Fibres

Alkyd resin e.g., glyptal resin formed by Phthalic anhydride and glycerine is not used (A) For surface coating of automobiles & air crafts (B) For fibre making (C) As plasticiser for PVC & nitrocellulose (D) For film forming materials

Description : Alkyd resin e.g., glyptal resin formed by Phthalic anhydride and glycerine is not used (A) For surface coating of automobiles & air crafts (B) For fibre making (C) As plasticiser for PVC & nitrocellulose (D) For film forming materials

Last Answer : (B) For fibre making

The main use of butadiene is (A) As a plasticiser for unsaturated polyester (B) In the manufacture of synthetic rubber (C) As an anti-skimming agent in paint (D) None of these

Description : The main use of butadiene is (A) As a plasticiser for unsaturated polyester (B) In the manufacture of synthetic rubber (C) As an anti-skimming agent in paint (D) None of these

Last Answer : (B) In the manufacture of synthetic rubber

Margarine is a/an (A) Fat (B) Explosive (C) Plasticiser (D) Rocket propellant

Description : Margarine is a/an (A) Fat (B) Explosive (C) Plasticiser (D) Rocket propellant

Last Answer : (A) Fat

Aryl benzene sulphonate (ABS) is a (A) Detergent (B) Plasticiser for unsaturated polyester (C) Starting material for the synthesis of glycerine (D) Coating ingredient for photographic film

Description : Aryl benzene sulphonate (ABS) is a (A) Detergent (B) Plasticiser for unsaturated polyester (C) Starting material for the synthesis of glycerine (D) Coating ingredient for photographic film

Last Answer : (A) Detergent

The major use of butadiene is (A) As a plasticiser for unsaturated polyester (B) In the manufacture of synthetic rubber (C) As an anti-skinning agent in paint (D) None of these

Description : The major use of butadiene is (A) As a plasticiser for unsaturated polyester (B) In the manufacture of synthetic rubber (C) As an anti-skinning agent in paint (D) None of these

Last Answer : (B) In the manufacture of synthetic rubber

Carbon disulphide is mainly used in the production of(A) Viscose rayon(B) Corundum(C) Plasticiser for unsaturated polyester(D) Paints

Description : Carbon disulphide is mainly used in the production of(A) Viscose rayon (B) Corundum (C) Plasticiser for unsaturated polyester (D) Paints

Last Answer : (A) Viscose rayon

Branched chain polymers compared to linear polymers have higher (A) Density (B) Tensile strength (C) Melting point (D) Degree of irregularity in atomic packing

Description : Branched chain polymers compared to linear polymers have higher (A) Density (B) Tensile strength (C) Melting point (D) Degree of irregularity in atomic packing

Last Answer : (D) Degree of irregularity in atomic packing

Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Description : Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Last Answer : (A) Good mechanical strength

Branched chair polymers as compared to linear polymers have (A) Higher melting point (B) Higher tensile strength (C) Lower density (D) None of these

Description : Branched chair polymers as compared to linear polymers have (A) Higher melting point (B) Higher tensile strength (C) Lower density (D) None of these

Last Answer : (C) Lower density

Volatile hydrocarbons are not used in the brakes of automobile as lubricants, but non-volatile hydrocarbons are used as lubricants.

Description : Volatile hydrocarbons are not used in the brakes of automobile as lubricants, but non-volatile hydrocarbons are used as lubricants.

Last Answer : Ans.: The vapour pressure of volatile hydrocarbons is very high and they get evaporated leaving behind the system. Due to this they are not used as lubricants in automobiles. Nonvolatile hydrocarbons having low vapour pressure are used as lubricants.

Crystallisation of polymers is an undesirable property. Crystallisation of celluloid is prevented by adding (A) Glycerol (B) Nitro cellulose (C) Camphor (D) None of these

Description : Crystallisation of polymers is an undesirable property. Crystallisation of celluloid is prevented by adding (A) Glycerol (B) Nitro cellulose (C) Camphor (D) None of these

Last Answer : (C) Camphor

Pick up the correct statement from the following: (A) The property of a soil that enables it to become stiff in a relatively short time on standing is called thixotropy (B) The ratio of shear strength in natural state to the remoulded shear strength under undrained conditions is called degree of sensitivity (C) The difference between the undisturbed shear strength and remoulded shear strength is known remoulding loss (D) All the above

Description : Pick up the correct statement from the following: (A) The property of a soil that enables it to become stiff in a relatively short time on standing is called thixotropy (B) The ratio ... the undisturbed shear strength and remoulded shear strength is known remoulding loss (D) All the above

Last Answer : (D) All the above

The marketers of Bic razor blades are using a strategy that includes large advertising expenditures and more price flexibility within the various types of blades offered. Based on this example, razor blades are probably in the __________ stage of the product life cycle. A)decline B)growth C)introduction D)maturity

Description : The marketers of Bic razor blades are using a strategy that includes large advertising expenditures and more price flexibility within the various types of blades offered. Based on this example, razor ... the __________ stage of the product life cycle. A)decline B)growth C)introduction D)maturity

Last Answer : D)maturity

Pick up the correct statement from the following: (A) The concrete gains strength due to hydration of cement (B) The concrete does not set at freezing point (C) The strength of concrete increases with its age (D) All the above

Description : Pick up the correct statement from the following: (A) The concrete gains strength due to hydration of cement (B) The concrete does not set at freezing point (C) The strength of concrete increases with its age (D) All the above

Last Answer : Answer: Option D