State the equation of cutting speed for milling operation

State the equation of cutting speed for milling operation
by

1 Answer

Answer :

Ans: The equation for cutting speed for milling calculation is

image

Where d = diameter of cutter(m) ,N= Cutter speed (RPM)

by

Related questions

In cell formation using production flow analysis, the following process will be left out of theanalysis a.Grinding b.Milling c.Drilling d.Gear cutting

Description : In cell formation using production flow analysis, the following process will be left out of theanalysis a.Grinding b.Milling c.Drilling d.Gear cutting

Last Answer : d.Gear cutting

Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove

Description : Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove

Last Answer : (i) Gear Tooth : Form milling cutter, Cylindrical type or End mill type, Gear cutter. (ii) Parting off: Slitting Cutter (iii) Keyway : Staggered teeth side milling cutter, End mill cutter, key ... milling cutter. Selection of a cutter depends upon type and size of slot or groove to be produced. 

If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B. starting winding will burn out C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Description : If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B ... C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Last Answer : Answer: B

Which one of the process is subtractive prototyping? a.5 axis CNC Milling b.Fused Deposition Modeling c.Multi-Jet Modeling d.Stereolithography Apparatus

Description : Which one of the process is subtractive prototyping? a.5 axis CNC Milling b.Fused Deposition Modeling c.Multi-Jet Modeling d.Stereolithography Apparatus

Last Answer : a.5 axis CNC Milling

Drilling, milling and threading are examples of which kind of processes? a.Additive manufacturing b.Subtractive manufacturing c.Formative manufacturing d.None of the above

Description : Drilling, milling and threading are examples of which kind of processes? a.Additive manufacturing b.Subtractive manufacturing c.Formative manufacturing d.None of the above

Last Answer : b.Subtractive manufacturing

Which of the following is not subtractive process? a.Milling b.Stereo-lithography c.Sawing d.EDM

Description : Which of the following is not subtractive process? a.Milling b.Stereo-lithography c.Sawing d.EDM

Last Answer : b.Stereo-lithography

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

In which machine we get feedback? a.Lathe machine b.NC machine c.CNC machine d.Milling machine

Description : In which machine we get feedback? a.Lathe machine b.NC machine c.CNC machine d.Milling machine

Last Answer : c.CNC machine

CNC machining centres do not include operations like a.milling b.boring c.welding d.tapping

Description : CNC machining centres do not include operations like a.milling b.boring c.welding d.tapping

Last Answer : c.welding

Numerical control a.applies only to milling machines b.is a method for producing exact number of parts per hour c.is a method for controlling by means of set of instructions d.None of the mentioned

Description : Numerical control a.applies only to milling machines b.is a method for producing exact number of parts per hour c.is a method for controlling by means of set of instructions d.None of the mentioned

Last Answer : c.is a method for controlling by means of set of instructions

What are the benefits of down cut milling ?

Description : What are the benefits of down cut milling ?

Last Answer : The advantages of down cut milling are- 1. The downward pressure puts the workpiece on the table. 2. More depth of cut can be given. 3. Quick material removal is possible. 4. Increases production ... of the cutter do not rub against the workpiece surface. As a result, more heat is not generated.

What does milling mean ?

Description : What does milling mean ?

Last Answer : : The literal meaning of milling is the process of crushing or cutting with the help of crushing machine. This means that milling is the process of cutting the object with the help of ... processes performed by milling machines. Gear cutting , surface finishing , facing are some of these processes.

Milling machine vs Milling machine.

Description : What's the difference?

Last Answer : Milling machine is a milling machine tool.

__________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Description : __________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Last Answer : (D) Pebble

Flywheel is used in (A) Punch press (B) Drilling machine (C) Surface grinder (D) Milling machine

Description : Flywheel is used in (A) Punch press (B) Drilling machine (C) Surface grinder (D) Milling machine

Last Answer : (A) Punch press

Powder metallurgy process does not make metal powder by (A) Atomisation (B) Grinding/milling (C) Hammering (D) Electrolytic deposition

Description : Powder metallurgy process does not make metal powder by (A) Atomisation (B) Grinding/milling (C) Hammering (D) Electrolytic deposition

Last Answer : Option C

machine is used for "Threshing , Harvesting , Separating , Cleaning and Collecting grains " a) Lathe b) Milling c) Combine d) Forklift

Description : machine is used for "Threshing , Harvesting , Separating , Cleaning and Collecting grains " a) Lathe b) Milling c) Combine d) Forklift

Last Answer : Combine 

Milling a hundred pounds of wheat should yield ____ percent straight flour. a. 72 to 75 c. 88 to 90 b. 75 to 80 d. 68 to 70

Description : Milling a hundred pounds of wheat should yield ____ percent straight flour. a. 72 to 75 c. 88 to 90 b. 75 to 80 d. 68 to 70

Last Answer : a. 72 to 75

W yellow powder, mostly made of uranium, that is produced in the uranium milling process is called what?

Description : W yellow powder, mostly made of uranium, that is produced in the uranium milling process is called what?

Last Answer : ANSWER: YELLOWCAKE or AMMONIUM DIURANATE

Explain keyway milling process with standard milling cutters.

Description : Explain keyway milling process with standard milling cutters.

Last Answer : Keyway Milling Operation: This milling process produce keyway slot. The cutter use if thin size. This operation suited for long keyways. The position of the cutter is shown in figure. Standard ... and then the cut is taken. Woodruff key is produced by using a woodruff key slot cutter.

Classify various types of Milling Machines. List major parts of Universal Milling Machine.

Description : Classify various types of Milling Machines. List major parts of Universal Milling Machine.

Last Answer : Classification of Milling Machine:- 1) Column and Knee Type Milling Machine a. Plain or Horizontal Milling Machine b. Hand Milling Machine c. Vertical Milling Machine d. Universal Milling Machine e. Omniversal ... Base [2]Column [3]Knee [4]Saddle [5]Table [6]Overhanging arm [7]Spindle [8]Arbor

Explain Gang Milling Process.

Description : Explain Gang Milling Process.

Last Answer : Gang Milling Operation: It involves the use of a combination of more than two cutters, mounted on a common arbor, for milling a number of flat horizontal and vertical surfaces of a work piece ... . The cutting speed of a gang of cutters is calculated from the cutter of the largest diameter. 

In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine oil for the first four hours of operation C. baking the armature in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Description : In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine ... in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Last Answer : Answer: A

The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Description : The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Last Answer : (B) Attrition

In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Last Answer : ans c

The operation of cutting, picking, plucking digging or any combination of these for removing the whole crop or edible part of the crop from either under the ground or above the ground is called a. threshing b. Post harvesting d. None of above

Description : The operation of cutting, picking, plucking digging or any combination of these for removing the whole crop or edible part of the crop from either under the ground or above the ground is called a. threshing b. Post harvesting d. None of above

Last Answer : Ans-    c. Harvesting

Functions of mold board plough a. Cutting the furrow slice. c) body to yoke b. Increase the depth of operation. d) length of the beam

Description : Functions of mold board plough a. Cutting the furrow slice. c) body to yoke b. Increase the depth of operation. d) length of the beam

Last Answer : Cutting the furrow slice.

349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Last Answer : (d) Gathering loss

Prepare operation process sheet and decide sequence of operation for the component shown in Figure No. 1. Assume suitable material and cutting conditions.

Description : Prepare operation process sheet and decide sequence of operation for the component shown in Figure No. 1. Assume suitable material and cutting conditions.

Last Answer : Operation Sheet with correct sequence of operations for the above given component by assuming suitable material and cutting conditions is as shown in below table;

Thread cutting operation

Description : Thread cutting operation

Last Answer : Thread cutting operation:- The principle of thread cutting is to produce a helical groove on cylindrical/conical surfaces by feeding the tool longitudinally when the job is revolved between centers. In this operation, ... The longitudinal feed is equal to the pitch of the thread to be cut.

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

which inverse operation would be used to verify the following equation? 54 ÷ 9 = 6 -General Knowledge

Description : which inverse operation would be used to verify the following equation? 54 ÷ 9 = 6 -General Knowledge

Last Answer : 9 * 6 = 54 would be used to verify the inverse operation equation of 54 ÷ 9 = 6.

Explain the principle of operation of attracted armature relay with equation and characteristics curve.

Description : Explain the principle of operation of attracted armature relay with equation and characteristics curve.

Last Answer : Principle: It works on the principle that when a current is passed through a coil magnetic lines of force develop and the coil behaves like a magnet. When we place a magnetic material inside the coil it is ... ) time delay. If we want a time delay we can add a slug in the armature core.  

Which of the following Maxwell equations use curl operation? a) Maxwell 1st and 2nd equation b) Maxwell 3rd and 4th equation c) All the four equations d) None of the equations

Description : Which of the following Maxwell equations use curl operation? a) Maxwell 1st and 2nd equation b) Maxwell 3rd and 4th equation c) All the four equations d) None of the equations

Last Answer : a) Maxwell 1st and 2nd equation

Which of the following theorem use the curl operation? a) Green’s theorem b) Gauss Divergence theorem c) Stoke’s theorem d) Maxwell equation

Description : Which of the following theorem use the curl operation? a) Green’s theorem b) Gauss Divergence theorem c) Stoke’s theorem d) Maxwell equation

Last Answer : b) Gauss Divergence theorem

In the lathe it is the peripheral speed of the work piece cutting speed of tool is expressed inm/min, V is a.= 𝜋𝐷𝑁/1000 b.= 𝜋𝐷/1000 c.= 𝐷𝑁/1000 d.=𝜋𝐷𝑁/10

Description : In the lathe it is the peripheral speed of the work piece cutting speed of tool is expressed inm/min, V is a.= 𝜋𝐷𝑁/1000 b.= 𝜋𝐷/1000 c.= 𝐷𝑁/1000 d.=𝜋𝐷𝑁/10

Last Answer : a.= 𝜋𝐷𝑁/1000

High speed cutting tool steels contain about __________ percent of tungsten. (A) 6-8 (B) 18-20 (C) 30-35 (D) 50-55

Description : High speed cutting tool steels contain about __________ percent of tungsten. (A) 6-8 (B) 18-20 (C) 30-35 (D) 50-55

Last Answer : (B) 18-20

Highest cutting speed is achieved by the __________ tool material. (A) High speed steel (B) Carbide (C) Cast alloy (D) Plain carbon steel

Description : Highest cutting speed is achieved by the __________ tool material. (A) High speed steel (B) Carbide (C) Cast alloy (D) Plain carbon steel

Last Answer : (B) Carbide

Non-ferrous alloys used for making cutting tools need not have high (A) Abrasion resistance (B) Toughness (C) Red hardness (D) Cutting speed

Description : Non-ferrous alloys used for making cutting tools need not have high (A) Abrasion resistance (B) Toughness (C) Red hardness (D) Cutting speed

Last Answer : (C) Red hardness

In regard to carbide burs; the more number of cutting blades and low speed will result in: A. Less efficient cutting and a smoother surface B. Less efficient cutting and a rougher surface C. More efficient cutting and a smoother surface D. More efficient cutting and a rougher surface

Description : In regard to carbide burs; the more number of cutting blades and low speed will result in: A. Less efficient cutting and a smoother surface B. Less efficient cutting and a rougher surface C. More efficient cutting and a smoother surface D. More efficient cutting and a rougher surface

Last Answer : A. Less efficient cutting and a smoother surface

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Description : Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Last Answer : b)20-40m/s

Write type of chip formed with following factors. (i) High rake angle (ii) High cutting speed (iii) Small depth of cut (iv) Low cutting speed (v) Large depth of cut (vi) Low rake angle

Description : Write type of chip formed with following factors. (i) High rake angle (ii) High cutting speed (iii) Small depth of cut (iv) Low cutting speed (v) Large depth of cut (vi) Low rake angle

Last Answer : (i) High rake angle : Continuous chips (ii) High cutting speed : Continuous chips (iii) Small depth of cut : Continuous chips (iv) Low cutting speed :Continuous chips with built up edge (v) ... cut : Continuous chips with built up edge (vi) Low rake angle :Continuous chips with built up edge

Define cutting speed and feed in metal cutting process.

Description : Define cutting speed and feed in metal cutting process.

Last Answer : Cutting Speed: Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).  Feed : Feed is defined as the distance the tool travels during one revolution of the part. 

Cutting Speed

Description : Cutting Speed

Last Answer : Cutting Speed: - It is the speed at which the metal is removed by the tool from the work piece. In lathe it is the peripheral speed of the work past the cutting tool expressed in meter per ... degree of surface finish, rigidity of the machine tool being used, and type of coolant being used. 

Material having highest cutting speed is :

Description : Material having highest cutting speed is : (A) Cast iron (B) Bronze (C) Aluminium (D) High carbon steel

Last Answer : Material having highest cutting speed is : Aluminium

The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Description : The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Last Answer : Ans: all options are correct

1. With which game in Christianio Ronaldo associated? 2. How is angular speed of a whirlwind in a tornado towards the centre? 3. In which the claim of Ashoka’s greatness cheifly lay? 4. Sweating during exercise indicates operation of which process in the human body? 5. Which is the State having the largest population of scheduled castes?

Description : 1. With which game in Christianio Ronaldo associated? 2. How is angular speed of a whirlwind in a tornado towards the centre? 3. In which the claim of Ashoka's greatness cheifly lay? 4. ... the founder of world Economic Forum? 20. Which fungus is responsible for the tikka disease of groundnut?

Last Answer : Answer : 1. Football 2. Decreases rapidly 3. Promotion of welfare of his people 4. Osmoregulation 5. Utter Pradesh 6. Because it has high specific heat 7. Typhoons 8. Minor Rock Edict XIII 9. ... -Party 15. Sulphur 16. India Gate 17. 1890 18. Aryabhatta 19. Klaus Schwab 20. Cercosplora personata

State the principle of operation of the gear box in terms of Torque, speed and diameter of the gear.

Description : State the principle of operation of the gear box in terms of Torque, speed and diameter of the gear.

Last Answer : In a gear box, the counter shaft is mashed to the clutch with a use of a couple of gear. So the counter shaft is always in running condition. When the counter shaft is bring ... lubricant. This prevents excessive wear and early failure. Therefore a gearbox runs partially filled with lubricant oil.