Description : A CNC Lathe is usually a machine tool with Z axes is….. a.Line Joining origin and vertical movement b.Line perpendicular to Y axis c.Both A & B d.Line Joining Chuck centre & tail stock centre
Last Answer : d.Line Joining Chuck centre & tail stock centre
Description : In laminated object manufacturing (LOM), which of the following cutting strategy ispreferable? a.Directional scanning b.Zigzag tool paths c.Contouring and spiral paths d.Boundary cutting tool paths
Last Answer : d.Boundary cutting tool paths
Description : In which machine we get feedback? a.Lathe machine b.NC machine c.CNC machine d.Milling machine
Last Answer : c.CNC machine
Description : The machine tool, in which calculation and setting of the operating conditions like depth ofcut, feed, speed are done during the machining by the control system itself, is called a.Computer Numerical Control System b.Direct Numerical Control System c.Machining Center System d.Adaptive Control System
Last Answer : d.Adaptive Control System
Description : The tool of an NC machine has to move along a circular arc from (5, 5) to (10, 10) while performing an operation. The centre of the arc is at (10, 5). Which one of the following NC tool path command performs the ... b.N010 GO3 X10 Y10 X5 Y5 R5 c.N010 GO1 X5 Y5 X10 Y10 R5 d.N010 GO2 X5 Y5 X10 Y10 R5
Last Answer : a.N010 GO2 X10 Y10 X5 Y5 R5
Description : General pivot point rotation can be expressed as a.T(zr,yr).R(θ).T(-zr,-yr) = R(xr,yr,θ) b.T(xr,yr).R(θ).T(-xr,-yr) = R(xr,yr,θ) c.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ) d.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ)
Last Answer : b.T(xr,yr).R(θ).T(-xr,-yr) = R(xr,yr,θ)
Description : If point are expressed in homogeneous coordinates then the pair of (x, y) isrepresented as a.(x’, y’, z’) b.(x, y, z) c.(x’, y’, w’) d.(x’, y’, w)
Last Answer : d.(x’, y’, w)
Description : From which of the following is not the main element of Flexible manufacturing system a.Work handling system b.Material handling system c.Tool handling system d.Main frame computer
Last Answer : a.Work handling system
Description : In cell formation using production flow analysis, the following process will be left out of theanalysis a.Grinding b.Milling c.Drilling d.Gear cutting
Last Answer : d.Gear cutting
Description : Process of converting STL file model in to layers is called________in RP a.chopping b.slicing c.cutting d.trimming
Last Answer : b.slicing
Description : In a CNC program block, N05 GO1 G91 G33 X20 Z-40……, G33 refer to a.Peck Drilling b.Counter Boring c.Thread Cutting d.Grooving
Last Answer : c.Thread Cutting
Description : From the following which is not the application of AGV. a.Truck loading and unloading b.To change the tool c.Material transfer d.Paper roll transfer
Last Answer : b.To change the tool
Description : Among the following, which one is the earliest step in Data Processing for RapidPrototyping? a.Model slicing b.Part orientation c.Tool path generation d.Support generation
Last Answer : b.Part orientation
Description : Among the following, which one is the last step in Data Processing for Rapid Prototyping? a.Model slicing b.Part orientation c.Tool path generation d.Support generation
Last Answer : c.Tool path generation
Description : The lost motion in CNC machine tool is on account of a.Backlash in gearing b.Wind-up of drive shafts c.Deflection of machine tool members d.All the above
Last Answer : a.Backlash in gearing
Description : What is the full form of ATC? a.Automatic tool changer b.Arranged tool changer c.Automatic tool controller d.Arranged tool controller
Last Answer : a.Automatic tool changer
Description : Automatic tool change in CNC Machine code a.M05 b.M06 c.M07 d.M09
Last Answer : b.M06
Description : In CNC machining tool radius compensation turning the left mode ON programming contourdone by a.G40 b.G41 c.G42 d.G43
Last Answer : b.G41
Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation
Last Answer : b.Tool length offset H
Description : In how many ways CNC machine tool systems can be classified? a.2 b.3 c.4 d.5
Last Answer : b.3
Description : he depth that the tool is plunged into the surface is called as a.feed b.depth of cut c.depth of tool d.working depth
Last Answer : b.depth of cut
Description : n an NC machining operation, the tool has to be moved from point (5, 4) to point (7, 2) alonga circular path with centre at (5, 2). Before starting the operation, the tool is at (5, 4). The G and N codes for this motion ... 0 I5.0 J2.0 c.N010 GO1 X7.0 Y2.0 I5.0 J2.0 d.N010 GOO X7.0 Y2.0 I5.0 J2.0
Last Answer : b.N010 GO2 X7.0 Y2.0 I5.0 J2.0
Description : During the execution of a CNC part program block NO20 GO2 X45.0 Y25.0 R5.0the type of tool motion will be a.circular Interpolation – clockwise b.circular Interpolation – counter clockwise c.linear Interpolation d.rapid feed
Last Answer : a.circular Interpolation – clockwise
Description : A cylinder can be created by drawing a rectangular shape using the ________ tool. a.revolve b.sweep c.extrude d.all of the above
Last Answer : a.revolve
Description : Which of the following statement(s) is/are true concerning oxygen delivery? a. The amount of oxygen delivered to peripheral tissues is dependent upon the oxygen content in arterial blood and cardiac ... O2/dL d. Normal systemic oxygen delivery for a typical adult is approximately 1000 cc/min
Last Answer : Answer: a, c, d The amount of oxygen that is delivered to peripheral tissues is the product of the oxygen content in arterial blood times the cardiac output. Normally, oxygen content of arterial blood is ... of venous blood is 16 cc/dL. Hence, the normal arterial-venous difference is 4 cc O2/dL
Description : Secondary Linear Axes U,V & W are ……… to X,Y & Z-axis. a.Perpendicular b.Parallel c.Rotational d.All of the above
Last Answer : b.Parallel
Description : ____ is also known as work volume of robot a.Work envelope b.Speed of movement c.Load carrying capacity d.Precision of movement
Last Answer : a.Work envelope
Description : I inherited a lathe, The smaller I machine the smaller the speed or the smaller the smaller the piece?
Last Answer : This cannot be determined. It depends on the material on the tools used and also on the lathe itself.
Description : The operating range or reach capability of robot is known as ____ in robotics a.Roll b.Pitch c.Yaw d.Speed of movement
Last Answer : c.Yaw
Description : The speed at which robot is capable of manipulating its end effector is known as the____. a.Velocity of robot b.Maximum reach c.Speed of movement d.Load carrying capacity
Last Answer : c.Speed of movement
Description : A combination of equipment and controls which handles, stores and retrieves materials withprecision,accuracy and speed under a defined degree of automation is known as ____ a.Automated storage and retrieval system (AS/RS) b.Flexible manufacturing system c.Automated guided vehicle d.None of the above
Last Answer : a.Automated storage and retrieval system (AS/RS)
Description : Maximum spindle speed limitation code in CNC Machine a.G90 b.G91 c.G92 d.G93
Last Answer : c.G92
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)
Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)
Description : In a CAD package, mirror image of a 2D point P (5, 10) is to be obtained about a line whichpasses through the origin and makes an angle of 45° counterclockwise with the X-axis. The coordinates of the transformed point will be a.(7.5, 5) b.(10, 5) c.(7.5, -5) d.(10, -5)
Last Answer : b.(10, 5)
Description : How many nodes are there in a tetrahedron with curved sides element? a.6 b.8 c.10 d.12
Last Answer : c.10
Description : How many nodes are there in a hexahedron element? a.4 b.6 c.8 d.10
Last Answer : c.8
Description : A circle is passing through two end points A[6,4] and B[10,10]. Find center point ofcircle a.7,8 b.8,8 c.8,7 d.7,7
Last Answer : c.8,7
Description : In a 2-D CAD package, clockwise circular arc of radius, 5, specified from P1 (15,10)to P2 (10,15)will have its center at a.(10, 10) b.(15, 10) c.(15, 15) d.(10, 15)
Last Answer : a.(10, 10)
Description : A line AB with end points A (2, 1) & B (7, 6) is to be moved by 3 units in x-direction & 4units in y-direction. Calculate new coordinates of points B. a.(10, 2) b.(2, 10) c.(10, 10) d.(10, 5)
Last Answer : c.(10, 10)
Description : Write down the steps involved for internal thread cutting on lathe machine.
Last Answer : Steps involved for internal thread cutting on lathe machine 1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on the boring bar adjusted the angle of ... the start. 10) Keep going until the calculated depth of cut has been reached on the top slide.
Description : From the following which type of work envelope is made in jointed arm robot a.Rectangular work envelope b.Cylindrical work envelope c.Spherical or hemispherical work envelope d.C
Last Answer : b.Cylindrical work envelope
Description : From the following which type of work envelope is made in Cartesian coordinate robot. a.Square work envelope b.Spherical work envelope c.Cylindrical work envelope d.Rectangular work envelope
Last Answer : d.Rectangular work envelope
Description : The capacity of robot to carry load is known as_____. a.Load carrying capacity b.Work envelope c.Maximum reach d.None of the above
Last Answer : a.Load carrying capacity
Description : In the CNC machine which device used to hold the workpiece? a.Automatic pallet changer b.Automatic work part positioner c.A & B both d.None of the above
Last Answer : c.A & B both
Description : Which machine's spindle is used to horizontal work? a.UMC b.VMC c.HMC d.DNC
Last Answer : c.HMC
Description : In CNC systems multiple microprocessors and programmable logic controllers work a.in parallel b.in series c.one after the other d.for 80% of the total machining time
Last Answer : a.in parallel
Description : The software that is used to control the computer’s work flow, organize its data andperform housekeeping functions is known as a.operating software b.graphics software c.application software d.programming software
Last Answer : a.operating software
Description : A cement concrete road is 1000 m long, 8 m wide and 15 cm thick over the sub-base of 10 cm thick gravel. The box cutting in road crust is (A) 500 m3 (B) 1000 m3 (C) 1500 m3 (D) 2000 m3
Last Answer : (C) 1500 m3
Description : Which one of the following statements is TRUE? a.Teach pendant is used for lead-through teaching. b.Teach pendant is used for manual teaching. c.Teach pendant is used for off-line teaching of robots. d.Teach pendant is not used in robot teaching.
Last Answer : b.Teach pendant is used for manual teaching.