Why must you operate the exhaust blower before starting a boat and inboard gasoline engine?

Why must you operate the exhaust blower before starting a boat and inboard gasoline engine?
by

1 Answer

Answer :

To remove accumulated gasoline vapors from areas of the enginecompartment. Failure to do so can result in an explosion duringstart-up.
by

Related questions

Which of the following is recommended maintenance for an inboard boat?

Description : Which of the following is recommended maintenance for an inboard boat?

Last Answer : Constant oil changes must be made. Periodic parts must be exchanged, especially those made of zinc. Debris accumulated in the engine must be removed. Search for possible leaks in the engine.

If your inboard or outboard boat run aground what action should you take in addition to shift the weight away from the point of impact?

Description : If your inboard or outboard boat run aground what action should you take in addition to shift the weight away from the point of impact?

Last Answer : Place the drive in neutral.Check everyone onboard is OK.Check for leaks.Kill the engine and raise the skeg to check that the prop has not been damaged.If there is the depth try and reverse off.IF any of the above does not work, Radio for help.

How gasoline engine emission is controlled by engine design modification and treatment of exhaust gas?

Description : How gasoline engine emission is controlled by engine design modification and treatment of exhaust gas?

Last Answer : Methods used for controlling of gasoline engine emission by engine design modification are:- 1. Use of leaner air-fuel ratios: The carburetor may be modified to provide relatively lean air fuel mixtures ... ) to open and close the EGR valve. Thus it controls the amount of exhaust gas recalculated.

Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Description : Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Last Answer : ANSWER d. all of the above

Sometimes, when you change the running direction of a E/R blower (from supply to exhaust) it trips. Why?

Description : Sometimes, when you change the running direction of a E/R blower (from supply to exhaust) it trips. Why?

Last Answer : If the flaps of the blower are not set or opened properly or the filters are clogged, the air supply is affected and the blower may be overloaded causing it to trip. Ask E/O for more information.

The _____________ sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: a Explanation: The engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting while the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

State the functions of following elements: i) Diesel engine system ii) Air intake system iii) Engine exhaust system iv) Engine starting system.

Description : State the functions of following elements: i) Diesel engine system ii) Air intake system iii) Engine exhaust system iv) Engine starting system.

Last Answer : i) Diesel engine system:-  Four strokes Two strokes ii) Air intake system:- Air intake system is provided to supply air to engine cylinder for fuel combustion.  iii) Engine exhaust system ... provided to rotate the engine initially until the firing starts and engine run under its own power. 

Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Description : Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Last Answer : Answer: B

If your boat has a power ventilation system how long should you turn it on for after fueling and prior to starting the engine?

Description : If your boat has a power ventilation system how long should you turn it on for after fueling and prior to starting the engine?

Last Answer : Four minutes is the recommended time.

Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Description : Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Last Answer : ANSWER : A

Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Description : Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Last Answer : ANSWER : C

How do I compare the horsepower ratings of inboard vs. outboard motors - is one kind more powerful?

Description : How do I compare the horsepower ratings of inboard vs. outboard motors - is one kind more powerful?

Last Answer : Inboard engines are quieter and are normally more powerful than outboard motors. Outboards are normally less exspensive and easier to maintain.

What is the purpose of inboard ailerons

Description : What is the purpose of inboard ailerons

Last Answer : D. to reduce wing twist at high speed

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

Small amount of gasoline is added to alcohol to a) reduce the emission b) to increase the power output c) to increase the efficiency d) to improve cold weather starting

Description : Small amount of gasoline is added to alcohol to a) reduce the emission b) to increase the power output c) to increase the efficiency d) to improve cold weather starting

Last Answer : Answer: d Explanation: None.

Boiling range of motor gasoline is an indication of the (A) Case of starting (B) Rate of acceleration (C) Vapour locking tendency (D) All (A), (B) and (C)

Description : Boiling range of motor gasoline is an indication of the (A) Case of starting (B) Rate of acceleration (C) Vapour locking tendency (D) All (A), (B) and (C)

Last Answer : (B) Rate of acceleration

How long would an aluminum exhaust last with a diesel engine?

Description : Before he clogged himself with soot. And for comparison with a gasoline car - it happened here and there, but otherwise I don't know either, I've never had a car like that.

Last Answer : I haven't heard of aluminum exhaust here, maybe home production itself? on the other hand, I often hear them about the aluminized ones, I sometimes take them from the Polish izawit and I have no problems with them and it would not happen to me that he gets stuck.

The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Last Answer : ANSWER : B

If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Description : If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Last Answer : ANSWER : B

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Description : In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Last Answer : The compression ratio in a Compression Ignition (CI) engine is generally in between a. 8 to 13 b. 14 to 23 c. 20 to 28 d. 25 to 32 (Ans:b)

The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: d Explanation: The air inlet temperature sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength whereas the engine temperature sensor senses the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: c Explanation: The air flow sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel while exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: b Explanation: Only in exhaust gas sensor, output voltage changes in proportion to air-fuel ratio.

_____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Description : _____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Last Answer : Answer: b Explanation: Exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates airfuel ratio while engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting.

The mean effective pressure obtained from the engine indicator indicates the a. maximum pressure developed b. instantaneous pressure c. exhaust pressure d. average pressure

Description : The mean effective pressure obtained from the engine indicator indicates the a. maximum pressure developed b. instantaneous pressure c. exhaust pressure d. average pressure

Last Answer : ANSWER d. average pressure

Supercharging is the process of a. supplying the engine with air at a density greater than the density of the surrounding atmosphere b. providing forced cooling air c. injecting excess fuel d. raising the exhaust pressure

Description : Supercharging is the process of a. supplying the engine with air at a density greater than the density of the surrounding atmosphere b. providing forced cooling air c. injecting excess fuel d. raising the exhaust pressure

Last Answer : ANSWER a. supplying the engine with air at a density greater than the density of the surrounding atmosphere

Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : (3) compressing air in the cylinders Explanation: Diesel engines use the heat of compressed air to ignite the fuel (intakes air, compresses it, then injects fuel). Diesel engines need high compression ratios to generate the high temperatures required for fuel auto ignition.

As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts

Description : As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts

Last Answer : Answer: D

Pick out the wrong statement (A) Low ozone layer thickness in polar regions is due to cold climatic conditions (B) Amount of unburnt hydrocarbons emitted by two stroke petrol engine is more as compared to that emitted by a four stroke engine (C) Carbon monoxide present in the two stroke petrol engine exhaust is much less as compared to that emitted from a four stroke engine (D) Mercury as a pollutant can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

Description : Pick out the wrong statement (A) Low ozone layer thickness in polar regions is due to cold climatic conditions (B) Amount of unburnt hydrocarbons emitted by two stroke petrol engine is more ... can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

Last Answer : (D) Mercury as a pollutant can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog? (A) Nitrogen oxides (B) Hydrocarbons (C) Both 'a' & 'b' (D) Carbon monoxide

Description : Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog? (A) Nitrogen oxides (B) Hydrocarbons (C) Both 'a' & 'b' (D) Carbon monoxide

Last Answer : (C) Both 'a' & 'b'

A turbo chargers are driven by 1. Engine 2. Exhaust gas 3. Dynamo 4. PTO ans 2

Description : A turbo chargers are driven by 1. Engine 2. Exhaust gas 3. Dynamo 4. PTO ans 2

Last Answer : ans 2

It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Description : It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Last Answer : Thrust

In a four stroke I.C engine completing 3000rpm the natural frequency of vibration of the exhaust valve should be a. 1200 Hz b. 1000 Hz c. 600 Hz d. 120 Hz

Description : In a four stroke I.C engine completing 3000rpm the natural frequency of vibration of the exhaust valve should be a. 1200 Hz b. 1000 Hz c. 600 Hz d. 120 Hz

Last Answer : b. 1000 Hz

Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Last Answer : C. Direct connection with the engine power

Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Last Answer : B. Exhaust gases from engine

State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Description : State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Last Answer : Engine components Material Functions Piston Cat aluminum alloy To transmit the force of explosion to the crankshaft. To form seal so that the high pressure gases in ... atmosphere through the exhaust pipe after combustion stroke is completed. To keep back pressure minimum.

The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 %

Description : The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 % 

Last Answer : ANSWER: Y -- 35 % 

In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : compressing air in the cylinders

What is a 6 letter word starting with r for boat steering?

Description : What is a 6 letter word starting with r for boat steering?

Last Answer : It is a rudder.

Speed of a boat in standing water is 9kmph and the speed of the stream is 1.5kmph. A man rows to a place at a distance of 10.5 km and comes back to the starting point. Find the total time taken by him. A.24 hours B.16 hours C.20 hours D.15 hours

Description : Speed of a boat in standing water is 9kmph and the speed of the stream is 1.5kmph. A man rows to a place at a distance of 10.5 km and comes back to the starting point. Find the total time taken by him. A.24 hours B.16 hours C.20 hours D.15 hours

Last Answer : Answer- A Basic Formula: i. speed = distance traveled / time taken ii. speed of the stream = ½ (a-b) km/hr iii. speed in still water = ½ (a+b) km/hr Explanation: Speed in still water= ½ (a+b) = 9km ... gives a = 10.5km/hr ; b=7.5 kmphr Total time taken by him = 105/10.5 + 105/7.5 = 24 hours

A boys rows to a certain place and comes back, but by mistake he covers 2/3rd more distance while coming back. The total time for this journey is 20 hours. The ratio of speed of boat to that of stream is 2 : 1. If the difference between upstream and downstream speed is 24km/hr, then how much time will the man take to reach to starting point from his present position? A) 2hr 13mints B)1hr 30 mins C) 2hr 30mins D)1hr 40 mins

Description : A boys rows to a certain place and comes back, but by mistake he covers 2/3rd more distance while coming back. The total time for this journey is 20 hours. The ratio of speed of boat to that of ... starting point from his present position? A) 2hr 13mints B)1hr 30 mins C) 2hr 30mins D)1hr 40 mins

Last Answer : ANSWER : A Explanation: let speed of boat and stream be 2x and x respectively So downstream speed = 2x+x = 3x, and upstream speed = 2x-x = x Let total distance between points is d km So he covered d ... with speed 3x = 48 km/hr(downstream) So time is 80/36 * 60 = 133.33 minutes = 2hr 13mins

CNG stopped working for me. the car only runs on gasoline. The engine light is on. please what can be the cause?

Description : CNG does not work

Last Answer : I would check the fuses and see if the fuse has gone and read the engine light with diagnostics and find out what it says

What is the tightening of cylinder head bolt on KIA NAZA RIA 2.5L GASOLINE ENGINE?

Description : What is the tightening of cylinder head bolt on KIA NAZA RIA 2.5L GASOLINE ENGINE?

Last Answer : Need answer

Octane number of gasoline is obtained by comparing the performance of the engine when running on a mixture of the following hydrocarbons A. ethane and methane B. normal heptane and iso-octane C. iso-heptane and octane D. iso-octane and TEL

Description : Octane number of gasoline is obtained by comparing the performance of the engine when running on a mixture of the following hydrocarbons A. ethane and methane B. normal heptane and iso-octane C. iso-heptane and octane D. iso-octane and TEL

Last Answer : ANSWER : B

A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel cycle is higher than the Otto cycle, at a fixed compression ratio c. The compression ratio of a diesel engine is higher than that of an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Description : A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel ... an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Last Answer : ANSWER c. The compression ratio of a diesel engine is higher than that of an S.I engine