Which of these represent short in a series circuit?

 Which of these represent short in a series circuit? 

a) Increase in resistance b) Increase in current c) Increase in voltage d) Increase in conductance
by

1 Answer

Answer :

 Which of these represent short in a series circuit?  Increase in current

by

Related questions

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : -

Description : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

Last Answer : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - 10 KHz

When a pure inductor is connected in series with a lamp circuit, effect is: -

Description : When a pure inductor is connected in series with a lamp circuit, effect is: -  a) Dimmer b) Brighter c) Same d) Fused

Last Answer : When a pure inductor is connected in series with a lamp circuit, effect is: -  Dimmer 

Which of this represent the half-time constant?

Description : Which of this represent the half-time constant?  a) 0.693 T b) 0.504 T c) 0.876 T d) 0.450 T

Last Answer : Which of this represent the half-time constant?  0.693 T 

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across...

Description : With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

Last Answer : 0.7V

The purpose of the series quadrature windings in an Amplidyne -

Description : The purpose of the series quadrature windings in an Amplidyne -  a) Neutralize the effect of Armature Reaction b) Reduce commutation difficulties c) Increase the gain d) Increase the response time

Last Answer : The purpose of the series quadrature windings in an Amplidyne - Increase the gain 

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp?

Description : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

Last Answer : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

A 0 -10 mAPMMC ammeter reads 5 mA in a circuit; its bottom control spring snaps out suddenly the meter ...

Description :  A 0 -10 mAPMMC ammeter reads 5 mA in a circuit; its bottom control spring snaps out suddenly the meter will now read:- a) 5 mA b) 10 mA c) 2.5 mA d). 0

Last Answer :  A 0 -10 mAPMMC ammeter reads 5 mA in a circuit; its bottom control spring snaps out suddenly the meter will now read:- 0

When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:

Description : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:  a) Static strain are being measured b) Dynamic strain are being measured c) Both Static and dynamic strain are being measured d) None of the above

Last Answer : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when: Dynamic strain are being measured

A flasher circuit application is a : -

Description : A flasher circuit application is a : -  a) Safety blinkers for bicycles c) Street Light Control  b) Rides lighting d) Glow lamp

Last Answer : A flasher circuit application is a : - Safety blinkers for bicycles 

Which of the device is employed in substation to limit the short circuit current in the power system: a) Shunt condenser b) Reactor c) Series capacitor d) Shunt capacitor

Description : Which of the device is employed in substation to limit the short circuit current in the power system: a) Shunt condenser b) Reactor c) Series capacitor d) Shunt capacitor

Last Answer : Ans: B

A circuit that has one of two wires in contact with the hull of a ship, is called a _____________. A. grounded circuit B. short circuit C. series circuit D. closed circuit

Description : A circuit that has one of two wires in contact with the hull of a ship, is called a _____________. A. grounded circuit B. short circuit C. series circuit D. closed circuit

Last Answer : Answer: A

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Last Answer : Answer: D

Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Description : Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Last Answer : Answer: B

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

What is the effect on total resistance and total current in a circuit if a short occurs in (a) a parallel branch, and (b) in a series portion?

Description : What is the effect on total resistance and total current in a circuit if a short occurs in (a) a parallel branch, and (b) in a series portion?

Last Answer : (a) Total resistance decreases, total current increases (b) Total resistance decreases, total current increases

Who did the is a series of dots and lines to represent numbers and letters using a telegraph?

Description : Who did the is a series of dots and lines to represent numbers and letters using a telegraph?

Last Answer : Need answer

What does the WR series number represent on standard Wire Rope Isolator (WRI)?

Description : What does the WR series number represent on standard Wire Rope Isolator (WRI)?

Last Answer : The number following WR represents the wire diameter in 32nd of an inch. The WRS series isolators use 5/32” diameter wire.

In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?

Description : In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?

Last Answer : a. Data used by digital computers. b. Pulsed squarewave signals. c. Digitized analog waveforms.

………….. gives defining the flow of the data through and organization or a company or series of tasks that may or may not represent computerized processing. A) System process B) System flowchart C) System design D) Structured System

Description : ………….. gives defining the flow of the data through and organization or a company or series of tasks that may or may not represent computerized processing. A) System process B) System flowchart C) System design D) Structured System

Last Answer : B) System flowchart

A series of closely spaced contour lines represent a (a) Steep slope* (b) Gentle slope (c) Uniform slope (d) Plane surface

Description : A series of closely spaced contour lines represent a (a) Steep slope* (b) Gentle slope (c) Uniform slope (d) Plane surface

Last Answer : (a) Steep slope*

Chrysler's Chief Executive Officer is the company's spokesperson. His message has focused on concern for customers and product quality. Which aspect of implementing the marketing concept does this represent? A)Focusing on general conditions B)Stressing the short run C)Endorsement of the marketing concept by top management D)Development of an information system E)Restructuring of the organisation

Description : Chrysler's Chief Executive Officer is the company's spokesperson. His message has focused on concern for customers and product quality. Which aspect of implementing the marketing concept does ... concept by top management D)Development of an information system E)Restructuring of the organisation

Last Answer : C)Endorsement of the marketing concept by top management

The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Last Answer : Answer: D

Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Last Answer : Answer: D

The diagrams shown in the illustration represent a/an _______________. EL-0093 A. engine order telegraph circuit B. rudder angle indicator arrangement C. engine speed tachometer with repeaters D. sound powered telephone system

Description : The diagrams shown in the illustration represent a/an _______________. EL-0093 A. engine order telegraph circuit B. rudder angle indicator arrangement C. engine speed tachometer with repeaters D. sound powered telephone system

Last Answer : Answer: D

Which one of the following frequency meter is suitable for measuring radio frequency?

Description : Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

Last Answer : Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

Which of the following factors limit the deflection of the pointer of a PMMC instrument of about

Description : Which of the following factors limit the deflection of the pointer of a PMMC instrument of about 90o?  1. Its damping mechanism  2. Linearity of magnetic field in which the coil moves  3. Control spring arrangement  4. ... Only 1 and 3 (b) Only 2 and 4 (c) Only 2 and 3 (d) Only 1 and 4 

Last Answer : Which of the following factors limit the deflection of the pointer of a PMMC instrument of about 90o?  1. Its damping mechanism  2. Linearity of magnetic field in which the coil moves  3. Control spring arrangement  4. ... Only 1 and 3 (b) Only 2 and 4 (c) Only 2 and 3 (d) Only 1 and 4 

Torque/weight ratio of an instrument indicates

Description : Torque/weight ratio of an instrument indicates   (a) Selectivity (b) Accuracy (c) Fidelity (d) Sensitivity

Last Answer : Torque/weight ratio of an instrument indicates Sensitivity

Wagner's earth devices are used in AC bridge circuits for

Description : Wagner's earth devices are used in AC bridge circuits for (a) Eliminating the effect of earth capacitances (b) Eliminating the effect of intercomponent capacitances (c) Eliminating the effect of stray electrostatic fields (d) Shielding the bridge elements

Last Answer : Wagner's earth devices are used in AC bridge circuits for Eliminating the effect of earth capacitances

Loading effect is principally caused by instruments

Description : Loading effect is principally caused by instruments   (a) High resistance (b) Low sensitivity (c) High sensitivity (d) High range

Last Answer : B

Thermocouple instruments can be used for a frequency range upto

Description : Thermocouple instruments can be used for a frequency range upto   (a) 100Hz (b) 5000 Hz (c) 1 MHz (d) 50 MHz and above 

Last Answer : Thermocouple instruments can be used for a frequency range upto 50 MHz and above 

In a single phase induction energy meter, in order to obtain true value of energy, the shunt

Description : In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by   (a) 90o (b) 0o (c) 45o (d) 60o

Last Answer : In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by 90o

Gearing, blacklash, friction between moving parts and scale accuracies are generally known as

Description : Gearing, blacklash, friction between moving parts and scale accuracies are generally known as  (a) Instrument errors (b) Interference errors (c) Calibration errors (d) Interaction errors

Last Answer : Gearing, blacklash, friction between moving parts and scale accuracies are generally known as Instrument errors

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of

Description : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

Last Answer : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is 0.03 cm/V

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is

Description : The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

Last Answer : The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is 500 W

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

If stator field is rotating in clockwise direction rotor rotates in

Description : If stator field is rotating in clockwise direction rotor rotates in (A) any direction (B) cannot predict (C) anticlockwise (D) clockwise 

Last Answer : If stator field is rotating in clockwise direction rotor rotates in clockwise 

What is the vector location of TRAP interrupt?

Description : What is the vector location of TRAP interrupt? (A) 0000 h (B) 0008 h (C) 0014 h (D) 0024 h

Last Answer : What is the vector location of TRAP interrupt?  0024 h

An amplifier has a voltage gain of 50; this gain in dB will be

Description : An amplifier has a voltage gain of 50; this gain in dB will be (A) 34 dB (B) 68 dB (C) 41 dB (D) 14 dB 

Last Answer : An amplifier has a voltage gain of 50; this gain in dB will be 34 dB

Converter is a device for transforming

Description : Converter is a device for transforming (A) ac to dc (B) dc to dc (C) dc to ac (D) ac to ac

Last Answer : Converter is a device for transforming ac to ac

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is

Description : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

Last Answer : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is 1200 Hz

The grid in triodes is made in the form of

Description : The grid in triodes is made in the form of (A) mesh (B) metal strip (C) metallic cylinder (D) single filament wire 

Last Answer : The grid in triodes is made in the form of mesh

The 555 timer can be used in which of the following configurations ?

Description : The 555 timer can be used in which of the following configurations ?  a) astable, monostable b) monostable, bistable c) astable, toggled d) bistable, tristable

Last Answer : The 555 timer can be used in astable, monostable configurations.

The dc current through each diode in a bridge rectifier equals : -

Description : The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

Last Answer : The dc current through each diode in a bridge rectifier equals : - the load current

Intrinsic semiconductor material is characterized by a valence shell of how many electrons?

Description : Intrinsic semiconductor material is characterized by a valence shell of how many electrons? a) 1 b) 2 c) 4 d) 6

Last Answer : Intrinsic semiconductor material is characterized by a valence shell of 4 electrons.

Sample -and -hold circuits in ADCs are designed to : -

Description : Sample -and -hold circuits in ADCs are designed to : - a) sample and hold the output of the binary counter during the conversion process b) stabilize theAD Cs threshold c) voltage ... d) signal during the conversion process sample and hold the ADC staircase waveform during the conversion process

Last Answer : Sample -and -hold circuits in ADCs are designed to : - voltage during the conversion process stabilize the input analog 

Base 10 refers to which number system?

Description : Base 10 refers to which number system? a) binary coded decimal b) decimal c) octal d) hexadecimal

Last Answer : Base 10 refers to decimal number system.

A basic S -R flip-flop can be constructed by cross -coupling which basic logic gates : -

Description : A basic S -R flip-flop can be constructed by cross -coupling which basic logic gates : - a) AND or OR gates b) XOR or XNOR gates c) NOR or NAND gates d) AND or NOR gates

Last Answer : A basic S -R flip-flop can be constructed by cross -coupling which basic logic gates : - NOR or NAND gates

A zero -level detector is a -

Description : A zero -level detector is a - a) comparator with a sine wave output b) comparator with a trip point referenced to zero c) peak detector d) limiter

Last Answer : A zero -level detector is a - comparator with a trip point referenced to zero

A single transistor can be used to build which of the following digital logic gates : -

Description : A single transistor can be used to build which of the following digital logic gates : - a) AND gates b) OR gates c) NOT gates d) NAND gates

Last Answer : a