The headroom above a working platform must be at least? a. 1.6m b. 2.1m c. 2m d. 2.6m

The headroom above a working platform must be at least?
a. 1.6m
b. 2.1m
c. 2m
d. 2.6m
by

1 Answer

Answer :

c. 2m
by

Related questions

The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Description : The vertical spacing between ties must be no more than? a. 8m (26 feet) b. 10m (33 feet) c. 12m (39 feet) d. 6m (20 feet)

Last Answer : a. 8m (26 feet)

The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Description : The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Last Answer : a. 3 planks 675mm (27 inches)

The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Description : The travel distance to an exit point on a working platform must be no more than? a. 7.4m b. 45m c. 15m d. 60m

Last Answer : c. 15m

A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Description : A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Last Answer : b. 360mm (14 inches)

At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Description : At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Last Answer : c. Between 95 cm (38 inches) and 115 cm ( 45 inches)

The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Description : The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Last Answer : c. 150mm (6 inches)

Planks must be overlapped a minimum of ------

Description : Planks must be overlapped a minimum of ------

Last Answer : 12 inches.

The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Description : The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Last Answer : d. 25mm (1 inch)

What is the minimum height an access ladder must extend above the landing?

Description : What is the minimum height an access ladder must extend above the landing?

Last Answer : 1m

Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Description : Where must longitudinal (façade) bracing be installed on a length whose is greater than its height? a. Every Third post b. Every post c. Every Fifth post d. Every Second post

Last Answer : c. Every Fifth post

At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Description : At what angle must zig zag bracing be installed? a. 35-55 degree b. 35-60 degree c. 25-45 degree d. 35-70 degree

Last Answer : a. 35-55 degree

The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Description : The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Last Answer : b. 6mm ( ¼ inch)

hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Description : hat is the horizontal spacing between tie? a. No more than 5m (16 feet) b. No more than 9m (30 feet) c. No more than 7m (23 feet) d. No more than 38m (125 feet)

Last Answer : b. No more than 9m (30 feet)

What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Description : What is the minimum overlap required when splicing bracing? a. 300mm (12 inches) b. 400mm (16 inches) c. 600mm (24 inches) d. 450mm (18 inches)

Last Answer : a. 300mm (12 inches)

Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Description : Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Last Answer : b. 2/3 of the total threaded length showing

What is the maximum height allowed between ladder landings?

Description : What is the maximum height allowed between ladder landings?

Last Answer : 6m (or 3 lifts)

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

What maximum load would you place on a right angle coupler?

Description : What maximum load would you place on a right angle coupler?

Last Answer : 630kg (or 630kgf or 6.25kN)

What is the maximum load you would lift with a gin wheel?

Description : What is the maximum load you would lift with a gin wheel?

Last Answer : 50kg

What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Description : What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Last Answer : b. 300mm (12 inches)

What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Description : What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Last Answer : b. Three

What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Description : What is the main function of bracing? a. To correct any incorrect measurements b. To enable easy inspection of the scaffold c. To make the scaffold square d. To add rigidity to the scaffold

Last Answer : d. To add rigidity to the scaffold

What minimum width of timber would you use as a soleplate?

Description : What minimum width of timber would you use as a soleplate?

Last Answer : 220mm (or 225mm, or the width of a scaffold plank)

What is the minimum size of a square baseplate?

Description : What is the minimum size of a square baseplate?

Last Answer : 150mm x 150mm (or 225cm2)

What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Description : What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Last Answer : c. 150mm (6 inches

Three charged cylindrical sheets are present in three spaces with σ = 5 at R = 2m, σ = - 2 at R = 4m and σ = -3 at R = 5m. Find the flux density at R = 6m. a) 17/6 b) -17/6 c) 13/6 d) -13/6

Description : Three charged cylindrical sheets are present in three spaces with σ = 5 at R = 2m, σ = - 2 at R = 4m and σ = -3 at R = 5m. Find the flux density at R = 6m. a) 17/6 b) -17/6 c) 13/6 d) -13/6

Last Answer : d) -13/6

If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2(D) D/6m(h1 - h2)3

Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3

Last Answer : (C) D/6m(h1 - h2)2

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with ... P_(2) = 32 J//s` D. None of these

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `16 N` C. `24 N` D. `32 N`

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `0` B. `2A` C. `4A` D. `6A`

What fraction of 2m 50cm is 1m 50cm?

Description : What fraction of 2m 50cm is 1m 50cm?

Last Answer : It is 150/250 or 3/5 in its simplest form

Four wires of the same material and dimensions as under are stretched by a load of same magnitude separately. Which of them will be elongated maximum? (a) wire of 3m length and 1.5 mm diameter (b) wire of 1m length and 2mm diameter (c) wire of 2m length and 2mm diameter (d) wire of 1m length and 1mm diameter

Description : Four wires of the same material and dimensions as under are stretched by a load of same magnitude separately. Which of them will be elongated maximum? (a) wire of 3m length and 1.5 mm diameter (b) ... and 2mm diameter (c) wire of 2m length and 2mm diameter (d) wire of 1m length and 1mm diameter

Last Answer : Ans:(a)

Which of the listed conditions occur when selection is made for 'third point hoist' on the winch shown in the illustration? EL-0102 A. Master switch contacts '5', '6', '7', '8', and '9' close. B. Contactors '2M', '3M', '4M' and '1A' pick up. C. Contactors '1M', 3M', '1A' and '2A' drop out. D. Master switch contacts '3','4', '6', '8', and '9' close.

Description : Which of the listed conditions occur when selection is made for 'third point hoist' on the winch shown in the illustration? EL-0102 A. Master switch contacts '5', '6', '7', '8', and '9' close. B. Contactors '2M', ' ... ' and '2A' drop out. D. Master switch contacts '3','4', '6', '8', and '9' close.

Last Answer : Answer: D

Three charged cylindrical sheets are present in three spaces with σ = 5 at R = 2m, σ = - 2 at R = 4m and σ = -3 at R = 5m. Find the flux density at R = 1m. a) 0 b) 1 c) 2 d) 3

Description : Three charged cylindrical sheets are present in three spaces with σ = 5 at R = 2m, σ = - 2 at R = 4m and σ = -3 at R = 5m. Find the flux density at R = 1m. a) 0 b) 1 c) 2 d) 3

Last Answer : a) 0

Find the potential due to a charged ring of density 2 units with radius 2m and the point at which potential is measured is at a distance of 1m from the ring. a) 18π b) 24π c) 36π d) 72π

Description : Find the potential due to a charged ring of density 2 units with radius 2m and the point at which potential is measured is at a distance of 1m from the ring. a) 18π b) 24π c) 36π d) 72π

Last Answer : d) 72π

The potential of a coaxial cylinder with charge density 1 unit , inner radius 1m and outer cylinder 2m is (in 10 9 ) a) 12.74 b) 13.47 c) 12.47 d) 13.74

Description : The potential of a coaxial cylinder with charge density 1 unit , inner radius 1m and outer cylinder 2m is (in 10 9 ) a) 12.74 b) 13.47 c) 12.47 d) 13.74

Last Answer : c) 12.47

To prevent segregation the concrete should to be thrown from a height of more than. (a) ½ m (b) 1m (c) 1.5m (d) 2m

Description : To prevent segregation the concrete should to be thrown from a height of more than. (a) ½ m (b) 1m (c) 1.5m (d) 2m

Last Answer : (b) 1m

One tesla equals a) 1 NA-1m -1 b) 1 NA-2m -3 c) 1NAm-1 d) 1NA-1 m

Description : One tesla equals a) 1 NA-1m -1 b) 1 NA-2m -3 c) 1NAm-1 d) 1NA-1 m

Last Answer : a) 1 NA-1m -1

Rail Cluster, as temporary arrangement can be used upto a span of a) 3.66m* b) 6.1m c) 12.2m d) 18.3 m

Description : Rail Cluster, as temporary arrangement can be used upto a span of a) 3.66m* b) 6.1m c) 12.2m d) 18.3 m

Last Answer : a) 3.66m*

One kg of gas occupying 0.1m^3 at pressure of 14 bar is expanded at constant pressure to 0.2m^3. Determine an initial and final temperature of gas. Take Cp=1.008KJ/KgK, Cv =0.72KJ/KgK.

Description : One kg of gas occupying 0.1m^3 at pressure of 14 bar is expanded at constant pressure to 0.2m^3. Determine an initial and final temperature of gas. Take Cp=1.008KJ/KgK, Cv =0.72KJ/KgK.

Last Answer : V1=0.1m^3 V2=0.2 m^3 P1=P2=14 bar Cp=1.008 KJ/KgK Cv=0.72 KJ/KgK R=Cp-Cv R=1.008-0.72 R=0.288KJ/KgK Characteristic gas equation,  P1V1=mRT1 14*10^5*0.1=1*288*T1 T1=486.11K For constant pressure process, V1/T1=V2/T2 0.1/486.11=0.2/T2 T2=972.22K

The lintels are preferred to arches because (A) Arches require more headroom to span the openings like doors, windows etc. (B) Arches require strong abutments to withstand arch thrust (C) Arches are difficult in construction (D) All of the abo

Description : The lintels are preferred to arches because (A) Arches require more headroom to span the openings like doors, windows etc. (B) Arches require strong abutments to withstand arch thrust (C) Arches are difficult in construction (D) All of the above

Last Answer : Answer: Option D

Define the terms Newel post and Headroom in vertical communication.

Description : Define the terms Newel post and Headroom in vertical communication.

Last Answer : Newel post : This is the vertical member which is placed at the ends of flights to connect the end of strings and hand rail.  Headroom : The vertical distance between the nosing of one flight and bottom of flight immediately above is known as the headroom.

An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Description : An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Last Answer : b. 28,600 kg

An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Description : An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Last Answer : b. 28,600 kg

A good photographic print is obtained by an exposure of 2s at a distance of 1m from a 60 candela lamp. What time of exposure must be given to get equa

Description : A good photographic print is obtained by an exposure of 2s at a distance of 1m from a 60 candela lamp. What time of exposure must be given to get equa

Last Answer : A good photographic print is obtained by an exposure of 2s at a distance of 1m from a 60 candela lamp ... at a distance of 2m from a 200 cadela lamp ?

A car moving with a speed of 40 km/h can be stopped by applying brakes after at least 2m. If the same car is moving with a speed of 80 km/h., what is

Description : A car moving with a speed of 40 km/h can be stopped by applying brakes after at least 2m. If the same car is moving with a speed of 80 km/h., what is

Last Answer : A car moving with a speed of 40 km/h can be stopped by applying brakes after at least 2m. If the same car is moving ... A. 2 m B. 4 m C. 6 m D. 8 m

To perform microminiature component repair, a 2M technician must be currently certified in what area?

Description : To perform microminiature component repair, a 2M technician must be currently certified in what area?

Last Answer : Microminiature component repair.

A satellite of mass "M" is in orbit around the earth. If a second satellite of mass "2M" is to be placed in the same orbit, the second satellite must have a velocity which is: w) half the velocity of the first satellite x) the same as the velocity of the first satellite y) twice the velocity of the first satellite z) four times the velocity of the first satellite

Description : A satellite of mass "M" is in orbit around the earth. If a second satellite of mass "2M" is to be placed in the same orbit, the second satellite must have a velocity which is: w) half ... first satellite y) twice the velocity of the first satellite z) four times the velocity of the first satellite

Last Answer : ANSWER: X -- THE SAME AS THE VELOCITY OF THE FIRST SATELLITE 

What does the Sydney, Australia median house price of $1.6m AUD buy in your town?

Description : What does the Sydney, Australia median house price of $1.6m AUD buy in your town?

Last Answer : Five 3-br 1 1/5 baths houses

How much dirt is in a hole that was dug 5m deep and 6m wide? -Riddles

Description : How much dirt is in a hole that was dug 5m deep and 6m wide? -Riddles

Last Answer : There is no dirt because it was dug out.