The frequency on which ATIS can be found is: a. Discrete VHF or VOR frequency b. Discrete VHF only c. VOR frequency only d. Any ATC frequency

The frequency on which ATIS can be found is:  
a. Discrete VHF or VOR frequency  
b. Discrete VHF only  
c. VOR frequency only  
d. Any ATC frequency
by

1 Answer

Answer :

a. Discrete VHF or VOR frequency
by

Related questions

The frequency on which ATIS can be found is: a. Discrete VHF or VOR frequency b. Discrete VHF only c. VOR frequency only d. Any ATC frequency

Description : The frequency on which ATIS can be found is: a. Discrete VHF or VOR frequency b. Discrete VHF only c. VOR frequency only d. Any ATC frequency

Last Answer : a. Discrete VHF or VOR frequency

In what frequency band is the ATIS normally broadcasted? a. LF b. HF c. ADF d. VHF

Description : In what frequency band is the ATIS normally broadcasted? a. LF b. HF c. ADF d. VHF

Last Answer : d. VHF

In what frequency band is the ATIS normally broadcasted? a. LF b. HF c. ADF d. VHF

Description : In what frequency band is the ATIS normally broadcasted?  a. LF  b. HF  c. ADF  d. VHF

Last Answer : d. VHF

DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Description : DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Last Answer : c. Cockpit workload is reduced

The frequency band of the ILS glidepath is: a. UHF b. VHF c. SHF d. VLF

Description : The frequency band of the ILS glidepath is: a. UHF b. VHF c. SHF d. VLF

Last Answer : a. UHF

The IRS position can be updated: a. On the ground only b. At designated positions en-route and on the ground c. On the ground and overhead VOR/DME d. At selected waypoints and on the ground

Description : The IRS position can be updated: a. On the ground only b. At designated positions en-route and on the ground c. On the ground and overhead VOR/DME d. At selected waypoints and on the ground

Last Answer : a. On the ground only

In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue the flight as per the ATC clearance received if possible b. Squawk 7500 and broadcast a warning to ATC other traffic on 121.500MHz or the frequency in use whilst maintaining the flight as cleared c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan d. If forced to deviate from the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Description : In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue ... the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Last Answer : c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan

The minimum content of a readback of the message from ATC “X-CD CHANGE FREQUENCY TO STEPHENVILLE TOWER 118.7” is: a. 118.7 b. CHANGING FREQUENCY X-CD c. TO STEPHENVILLE X-CD d. 118.7 X-CD

Description : The minimum content of a readback of the message from ATC “X-CD CHANGE FREQUENCY TO STEPHENVILLE TOWER 118.7” is: a. 118.7 b. CHANGING FREQUENCY X-CD c. TO STEPHENVILLE X-CD d. 118.7 X-CD

Last Answer : d. 118.7 X-CD

The ATC message “DISTRESS TRAFFIC ENDED” signifies that: a. All traffic are to end their transmissions b. All aircraft on the frequency are to change to another frequency c. Normal ATC is resumed after an emergency d. ATC is shutting shop

Description : The ATC message “DISTRESS TRAFFIC ENDED” signifies that: a. All traffic are to end their transmissions b. All aircraft on the frequency are to change to another frequency c. Normal ATC is resumed after an emergency d. ATC is shutting shop

Last Answer : c. Normal ATC is resumed after an emergency

An aircraft is required to intercept and home to a VOR along the 064 radial. The OBS should be set to: a. 064 to get the correct needle sense and a TO indication b. 244 to get the correct needle sense and a TO indication c. 064 to get the correct needle sense and a FROM indication d. 244 to get the correct needle sense and a FROM indication

Description : An aircraft is required to intercept and home to a VOR along the 064 radial. The OBS should be set to: a. 064 to get the correct needle sense and a TO indication b. 244 to get the ... the correct needle sense and a FROM indication d. 244 to get the correct needle sense and a FROM indication

Last Answer : b. 244 to get the correct needle sense and a TO indication

Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB b. That the aircraft is heading 330° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB c. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 050° (M) from the NDB d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Description : Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M ... 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Last Answer : d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

At a range of 200nm from a VOR, if there is an error of 1°, how far off the centreline is the aircraft? a. 3.5nm b. 1.75nm c. 7nm d. 1nm

Description : At a range of 200nm from a VOR, if there is an error of 1°, how far off the centreline is the aircraft? a. 3.5nm b. 1.75nm c. 7nm d. 1nm

Last Answer : a. 3.5nm

Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB b. That the aircraft is heading 330° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB c. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 050° (M) from the NDB d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Description : Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M ... 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Last Answer : d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

An aircraft is attempting to home to a VOR on the 064 radial. The CDI shows 4 dots fly right with a TO indication. At the same time the co-located DME shows a range of 45nm. Where is the aircraft in relation to the required track? a. 6nm right of track b. 3nm right of track c. 6nm left of track d. 3nm left of track

Description : An aircraft is attempting to home to a VOR on the 064 radial. The CDI shows 4 dots fly right with a TO indication. At the same time the co-located DME shows a range of 45nm. Where is the aircraft in relation ... right of track b. 3nm right of track c. 6nm left of track d. 3nm left of track

Last Answer : c. 6nm left of track

An aircraft wishes to track a VOR along the 274 radial. If variation is 10° W, what should be set on the OBS? a. 274 b. 264 c. 094 d. 084

Description : An aircraft wishes to track a VOR along the 274 radial. If variation is 10° W, what should be set on the OBS? a. 274 b. 264 c. 094 d. 084

Last Answer : c. 094

An aircraft is tracking inbound to a VOR beacon on the 105 radial. The setting the pilot should put on the OBS and the CDI indications are: a. 285, TO b. 105, TO c. 285, FROM d. 105, FROM

Description : An aircraft is tracking inbound to a VOR beacon on the 105 radial. The setting the pilot should put on the OBS and the CDI indications are: a. 285, TO b. 105, TO c. 285, FROM d. 105, FROM

Last Answer : a. 285, TO

The VOR indications on an RMI whose deviation is not zero: a. Are magnetic b. Are compass c. Are relative d. Must have deviation applied before being used

Description : The VOR indications on an RMI whose deviation is not zero: a. Are magnetic b. Are compass c. Are relative d. Must have deviation applied before being used

Last Answer : a. Are magnetic

A basic 2D RNAV system will determine tracking information from: a. Twin DME b. VOR/DME c. Twin VOR d. Any of the above

Description : A basic 2D RNAV system will determine tracking information from: a. Twin DME b. VOR/DME c. Twin VOR d. Any of the above

Last Answer : b. VOR/DME

Which of the following would give the best indication of speed? a. A VOR on the flight plan route b. A VOR off the flight plan route c. A DME on the flight plan route d. A DME off the flight plan route

Description : Which of the following would give the best indication of speed? a. A VOR on the flight plan route b. A VOR off the flight plan route c. A DME on the flight plan route d. A DME off the flight plan route

Last Answer : c. A DME on the flight plan route

In a Doppler VOR (DVOR) the reference signal is _____, the bearing signal is ______ and the direction of rotation of the bearing signal is ______. a. AM, FM, anti-clockwise b. AM, FM, clockwise c. FM, AM, anti-clockwise d. FM, AM, clockwise

Description : In a Doppler VOR (DVOR) the reference signal is _____, the bearing signal is ______ and the direction of rotation of the bearing signal is ______. a. AM, FM, anti-clockwise b. AM, FM, clockwise c. FM, AM, anti-clockwise d. FM, AM, clockwise

Last Answer : a. AM, FM, anti-clockwise

What radius from a terminal VOR is MSA provided? a. 25nm b. 10nm c. 15nm d. 15km

Description : What radius from a terminal VOR is MSA provided? a. 25nm b. 10nm c. 15nm d. 15km

Last Answer : a. 25nm

An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? a. When threshold and mid-runway RVRs are greater than 800m b. When all 3 RVRs are greater than 800m c. When the met viz is greater than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Description : An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? ... than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Last Answer : d. When threshold RVR is greater than 800m

With reference to Traffic Collision Avoidance Systems: a. RAs may be disregarded only when the pilot visually identifies the potentially conflicting traffic and decides that no deviation is necessary and has the clearance confirmed by ATC b. RAs may be disregarded only when the pilot visually identifies the potentially conflicting traffic and decides that no deviation is necessary and has advised ATC of the other aircraft’s proximity c. RAs must never be disregarded d. RAs may be disregarded only when the pilot visually identifies the potentially conflicting traffic and decides that no deviation is necessary

Description : With reference to Traffic Collision Avoidance Systems: a. RAs may be disregarded only when the pilot visually identifies the potentially conflicting traffic and decides that no deviation ... pilot visually identifies the potentially conflicting traffic and decides that no deviation is necessary

Last Answer : d. RAs may be disregarded only when the pilot visually identifies the potentially conflicting traffic and decides that no deviation is necessary

ATC will only report wind as gusting if: a. Gust speed exceeds mean speed by >15kts b. Gusts to over 25kts c. Gusts exceed mean speed by 10kts d. Gusts to under 25kts

Description : ATC will only report wind as gusting if: a. Gust speed exceeds mean speed by >15kts b. Gusts to over 25kts c. Gusts exceed mean speed by 10kts d. Gusts to under 25kts

Last Answer : c. Gusts exceed mean speed by 10kts

The instruction “ORBIT” from ATC means that the aircraft should: a. Carry out a go around b. Continue with 360 degree turns c. Carry out one 360 degree turn only d. Reverse the direction of the turn

Description : The instruction “ORBIT” from ATC means that the aircraft should: a. Carry out a go around b. Continue with 360 degree turns c. Carry out one 360 degree turn only d. Reverse the direction of the turn

Last Answer : c. Carry out one 360 degree turn only

If a transponder is unserviceable before an IFR departure, then the pilot: a. Has to cancel the flight b. May proceed with the flight with ATC permission c. Has to fly low level only d. Should fly for another company

Description : If a transponder is unserviceable before an IFR departure, then the pilot: a. Has to cancel the flight b. May proceed with the flight with ATC permission c. Has to fly low level only d. Should fly for another company

Last Answer : b. May proceed with the flight with ATC permission

When the aircraft carries serviceable Mode C transponder, the pilot shall continuously operate this mode: a. Only when directed by ATC b. Unless otherwise directed by ATC c. Only when the aircraft is flying within controlled airspace d. Regardless of ATC instructions

Description : When the aircraft carries serviceable Mode C transponder, the pilot shall continuously operate this mode: a. Only when directed by ATC b. Unless otherwise directed by ATC c. Only when the aircraft is flying within controlled airspace d. Regardless of ATC instructions

Last Answer : b. Unless otherwise directed by ATC

What is required for navigation in IMC? a. Radio equipment and equipment for guidance until visual point b. Anti-icing equipment c. A serviceable weather radar d. One VHF box and one HF box

Description : What is required for navigation in IMC? a. Radio equipment and equipment for guidance until visual point b. Anti-icing equipment c. A serviceable weather radar d. One VHF box and one HF box

Last Answer : a. Radio equipment and equipment for guidance until visual point

An aircraft has to communicate with a VHF station at a range of 300nm, if the ground station is situated 2,500ft amsl, which of the following is the lowest altitude at which contact is likely to be made? a. 190ft b. 1,378ft c. 36,100ft d. 84,100ft

Description : An aircraft has to communicate with a VHF station at a range of 300nm, if the ground station is situated 2,500ft amsl, which of the following is the lowest altitude at which contact is likely to be made? a. 190ft b. 1,378ft c. 36,100ft d. 84,100ft

Last Answer : c. 36,100ft

The full range of VHF frequencies used for communications is: a. 3 to 30 MHz b. 88 to 108 MHz c. 108.0 to 139.95 MHz d. 118.0 to 136.975 MHz

Description : The full range of VHF frequencies used for communications is: a. 3 to 30 MHz b. 88 to 108 MHz c. 108.0 to 139.95 MHz d. 118.0 to 136.975 MHz

Last Answer : d. 118.0 to 136.975 MHz

In the event of a precautionary landing, who is responsible for alerting the emergency services? a. ATC b. The Commander c. The local constabulary d. The Operations Dispatcher

Description : In the event of a precautionary landing, who is responsible for alerting the emergency services? a. ATC b. The Commander c. The local constabulary d. The Operations Dispatcher

Last Answer : a. ATC

On receipt of a TCAS RA, your action is to: a. Initiate the required maneuver immediately b. Make a note of the details c. Request a flight clearance deviation from ATC d. Do nothing until a TA is received

Description : On receipt of a TCAS RA, your action is to: a. Initiate the required maneuver immediately b. Make a note of the details c. Request a flight clearance deviation from ATC d. Do nothing until a TA is received

Last Answer : a. Initiate the required maneuver immediately

You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Description : You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Last Answer : c. 30 mins

The response to general call from ATC is for the aircraft to: a. Respond in alphabetic order b. Respond in numerical order c. Give no response d. Request a repeat of the message

Description : The response to general call from ATC is for the aircraft to: a. Respond in alphabetic order b. Respond in numerical order c. Give no response d. Request a repeat of the message

Last Answer : c. Give no response

The phrase “BRAKING CO-EFFICIENT 20” from ATC means that braking action: a. Poor b. Medium to poor c. Medium d. Slippery

Description : The phrase “BRAKING CO-EFFICIENT 20” from ATC means that braking action: a. Poor b. Medium to poor c. Medium d. Slippery

Last Answer : a. Poor

The message “CHECK” to an aircraft means that you should: a. Confirm that you received and understood the last message b. Pass the required information to ATC c. Stay where you are d. Examine a system or procedure

Description : The message “CHECK” to an aircraft means that you should: a. Confirm that you received and understood the last message b. Pass the required information to ATC c. Stay where you are d. Examine a system or procedure

Last Answer : d. Examine a system or procedure

Clearance limit is defined as: a. The flight level to which an aircraft is granted ATC clearance b. The time at which the ATC clearance expires c. The point to which aircraft is granted ATC clearance d. The height below which you will hit the first obstacle

Description : Clearance limit is defined as: a. The flight level to which an aircraft is granted ATC clearance b. The time at which the ATC clearance expires c. The point to which aircraft is granted ATC clearance d. The height below which you will hit the first obstacle

Last Answer : c. The point to which aircraft is granted ATC clearance

If an ATC clearance is not suitable, the PIC may: a. Offer ATC an acceptable clearance b. Request and if practicable accept an amended clearance c. Demand an alternative clearance and ATC must comply d. Decline the clearance on the grounds that it is not in accordance with the field flight plan

Description : If an ATC clearance is not suitable, the PIC may: a. Offer ATC an acceptable clearance b. Request and if practicable accept an amended clearance c. Demand an alternative clearance and ATC must ... d. Decline the clearance on the grounds that it is not in accordance with the field flight plan

Last Answer : b. Request and if practicable accept an amended clearance

Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless of the direction from which B approaches b. Aircraft B, regardless of the direction from which A approaches c. Aircraft A, if B is to the right of him d. Aircraft B, if A is to the left of him

Description : Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless ... , if B is to the right of him d. Aircraft B, if A is to the left of him

Last Answer : d. Aircraft B, if A is to the left of him

The person having overall responsibility of an aircraft during flight is the: a. Pilot in command b. Operator c. ATC controller if the aircraft is in controlled airspace d. Owner of the aircraft

Description : The person having overall responsibility of an aircraft during flight is the: a. Pilot in command b. Operator c. ATC controller if the aircraft is in controlled airspace d. Owner of the aircraft

Last Answer : a. Pilot in command

The transition from IFR to VFR is done: a. On the Captain’s initiative b. Whenever an aircraft in VMC leaves controlled airspace c. If told by ATC d. At the clearance limit, disregarding the weather situation

Description : The transition from IFR to VFR is done: a. On the Captain’s initiative b. Whenever an aircraft in VMC leaves controlled airspace c. If told by ATC d. At the clearance limit, disregarding the weather situation

Last Answer : a. On the Captain’s initiative

Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Description : Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Last Answer : b. If asked by ATC

The transition from IFR to VFR is done: a. On the Captain’s initiative b. Whenever an aircraft in VMC leaves controlled airspace c. If told by ATC d. At the clearance limit, disregarding the weather situation

Description : The transition from IFR to VFR is done: a. On the Captain’s initiative b. Whenever an aircraft in VMC leaves controlled airspace c. If told by ATC d. At the clearance limit, disregarding the weather situation

Last Answer : a. On the Captain’s initiative

When the Captain cannot comply with an ATC clearance: a. The Captain must accept the ATC clearance, because it is based on a filed flight plan b. He/she may request an amended clearance and, if executable, he/she will accept that clearance c. He/she may ask a new clearance and the appropriate ATC must grant him/her that clearance d. He/she may suggest a new clearance to ATC

Description : When the Captain cannot comply with an ATC clearance: a. The Captain must accept the ATC clearance, because it is based on a filed flight plan b. He/she may request an amended clearance and, if ... appropriate ATC must grant him/her that clearance d. He/she may suggest a new clearance to ATC

Last Answer : b. He/she may request an amended clearance and, if executable, he/she will accept that clearance

If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer correcting for wind c. Ignore the wind and proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Description : If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer ... proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Last Answer : a. Correct for the correct wind so as to stay within controlled airspace

A controlled flight is required to inform the concerned ATC unit when the average TAS at cruising level deviates or is expected to deviate compared to that given TAS in the Flight Plan by at least plus or minus: a. 10% b. 3% c. 5% d. 2%

Description : A controlled flight is required to inform the concerned ATC unit when the average TAS at cruising level deviates or is expected to deviate compared to that given TAS in the Flight Plan by at least plus or minus: a. 10% b. 3% c. 5% d. 2%

Last Answer : d. 2%

Except when cleared by an ATC unit, a VFR flight cannot enter or leave a Control Zone when the cloud base is lower than: a. 1000 feet and less than 8km visibility b. 2000 feet and less than 5km visibility c. 1500 feet or less than 5km visibility d. 1000 feet and less than 5km visibility

Description : Except when cleared by an ATC unit, a VFR flight cannot enter or leave a Control Zone when the cloud base is lower than: a. 1000 feet and less than 8km visibility b. 2000 feet and less than 5km visibility c. 1500 feet or less than 5km visibility d. 1000 feet and less than 5km visibility

Last Answer : c. 1500 feet or less than 5km visibility

When reporting a frequency the use of the word “DECIMAL” can be omitted: a. When there is no likelihood of confusion b. After the initial call c. Never d. By the ground station only

Description : When reporting a frequency the use of the word “DECIMAL” can be omitted: a. When there is no likelihood of confusion b. After the initial call c. Never d. By the ground station only

Last Answer : c. Never

The DME counters are rotating continuously. This indicates that: a. The DME is unserviceable b. The DME is trying to lock onto range c. The DME is trying to lock onto frequency d. The DME is receiving no response from the ground station

Description : The DME counters are rotating continuously. This indicates that: a. The DME is unserviceable b. The DME is trying to lock onto range c. The DME is trying to lock onto frequency d. The DME is receiving no response from the ground station

Last Answer : b. The DME is trying to lock onto range

Which frequency band is a wavelength of 1200m? a. UHF b. LF c. HF d. MF

Description : Which frequency band is a wavelength of 1200m? a. UHF b. LF c. HF d. MF

Last Answer : b. LF