The minimum diameter of turning besin, where ships turn by going ahead and without tug assistance should be (A) L (B) 1.5 L (C) 2.0 L (D) 4.0 L L he length of the largest ship to use the port

The minimum diameter of turning besin, where ships turn by going ahead and without tug
assistance should be
(A) L
(B) 1.5 L
(C) 2.0 L
(D) 4.0 L
L he length of the largest ship to use the port
by

1 Answer

Answer :

(D) 4.0 L
by

Related questions

Pick up the correct statement from the following: (A) An artificial barrier which makes the enclosed area safe for anchorage of ships, is known as break water (B) The break water whose inside is used as a platform for loading and unloading is called a mole (C) The length of the quay wall is governed by the length of the largest vessel likely to be berthed (D) All the abov

Description : Pick up the correct statement from the following: (A) An artificial barrier which makes the enclosed area safe for anchorage of ships, is known as break water (B) The break water whose inside is used ... wall is governed by the length of the largest vessel likely to be berthed (D) All the above

Last Answer : (D) All the above

A harbour is a place where (A) Ships get shelter and protection against destructive forces due to sea waves (B) Facilities are provided for receiving cargo and passengers (C) Port buildings are constructed for commercial purposes (D) All the above

Description : A harbour is a place where (A) Ships get shelter and protection against destructive forces due to sea waves (B) Facilities are provided for receiving cargo and passengers (C) Port buildings are constructed for commercial purposes (D) All the above

Last Answer : (D) All the above

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal a.the force applied on A must be equal to that on B b.at least one man on side B should be removed c.infinite force will be required to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Description : In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal ... to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Last Answer : c. infinite force will be required to be applied at both ends

What New York and tug hill landscape region is classified as a plateau because this region has a?

Description : What New York and tug hill landscape region is classified as a plateau because this region has a?

Last Answer : Feel Free to Answer

Why very heavy snowfall occurs in the Tug Hill Plateau region?

Description : Why very heavy snowfall occurs in the Tug Hill Plateau region?

Last Answer : Need answer

If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Description : If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Last Answer : Answer: Option D Answer: Option D

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)

Description : A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)

Last Answer : Answer: Option D

The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Description : The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Last Answer : Answer: Option D

The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Description : The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Last Answer : [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

If a ship had 26 sheep and 10 goats on board, how old is the ship's captain?

Description : If a ship had 26 sheep and 10 goats on board, how old is the ship's captain?

Last Answer : “Old enough to stick a fork in the throat of the author of this question.”

Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

When shore power is being connected to a ship in dry dock, _____________. A. the ship's generators are paralleled with the shore power to provide continuous power B. proper phase sequence must be established C. exactly 450 volts must be supplied from the shore D. exactly 60 Hz must be provided by the terminal

Description : When shore power is being connected to a ship in dry dock, _____________. A. the ship's generators are paralleled with the shore power to provide continuous power B. proper phase sequence must be ... 450 volts must be supplied from the shore D. exactly 60 Hz must be provided by the terminal

Last Answer : Answer: B

An electrical device which employs a stationary armature and a rotating electromagnetic field is used aboard ship as a ____________. A. magnetic amplifier B. ship's service alternator C. three-wire DC generator D. saturable core reactor

Description : An electrical device which employs a stationary armature and a rotating electromagnetic field is used aboard ship as a ____________. A. magnetic amplifier B. ship's service alternator C. three-wire DC generator D. saturable core reactor

Last Answer : Answer: B

In sailing ship days who often acted as the ships doctor

Description : In sailing ship days who often acted as the ships doctor

Last Answer : Cook

If N is the algebraic difference of grades, S is the minimum sight distance in metres, the length (L) of a summit curve is (A) NS/4 (B) NS²/4 (C) N²S/4(D) (NS)²/4

Description : If N is the algebraic difference of grades, S is the minimum sight distance in metres, the length (L) of a summit curve is (A) NS/4 (B) NS²/4 (C) N²S/4 (D) (NS)²/4

Last Answer : Answer: Option B

If N is the net difference of grades, S is the minimum overtaken sight distance in metres, the length (L) of a summit curve, is (A) NS/4 (B) NS²/4 (C) NS²/4.8 (D) NS²/9.6

Description : If N is the net difference of grades, S is the minimum overtaken sight distance in metres, the length (L) of a summit curve, is (A) NS/4 (B) NS²/4 (C) NS²/4.8 (D) NS²/9.6

Last Answer : Answer: Option D

Length of vehicles does not affect (A) Extra widening (B) Minimum radius of turning (C) Passing sight distance (D) Width of shoulders

Description : Length of vehicles does not affect (A) Extra widening (B) Minimum radius of turning (C) Passing sight distance (D) Width of shoulders

Last Answer : Answer: Option D

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

If h and h1 are the heights of a light house and the observer in a ship in metres above M S L then the horizontal distance from the ship to the light house in kilometres is (A) h + h1) (B) h - h1) (C) h × h1) (D) 3.86 h + h1)

Description : If h and h1 are the heights of a light house and the observer in a ship in metres above M S L then the horizontal distance from the ship to the light house in kilometres is (A) h + h1) (B) h - h1) (C) h × h1) (D) 3.86 h + h1)

Last Answer : (A) h + h1)

Minimum width of ship clearance shall be (A) B or 30 m (B) 1.5 B or 50 m (C) 1.5 B (D) 50 m

Description : Minimum width of ship clearance shall be (A) B or 30 m (B) 1.5 B or 50 m (C) 1.5 B (D) 50 m

Last Answer : (A) B or 30 m

The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above

Description : The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above

Last Answer : Answer: Option D

The king of Ceylon sent a ship carrying some gifts, some children and widow of an Arab trader. Ship was attacked at the coast of Sindh, by the pirates of the ruler of Sindh, the name of the coast was: A. Gomal B. Debul C. Port Qasim D. Gawader

Description : The king of Ceylon sent a ship carrying some gifts, some children and widow of an Arab trader. Ship was attacked at the coast of Sindh, by the pirates of the ruler of Sindh, the name of the coast was: A. Gomal B. Debul C. Port Qasim D. Gawader

Last Answer : ANSWER: B

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

The drift speed of electrons in copper wire of diameter and length `l` is `v` . If the potential difference across the wire is doubled, then the new d

Description : The drift speed of electrons in copper wire of diameter and length `l` is `v` . If the potential difference across the wire is doubled, then the new d

Last Answer : The drift speed of electrons in copper wire of diameter and length `l` is `v` . If the potential ... `2upsilon` C. `3upsilon` D. `upsilon//2`

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

A copper wire of length l and diameter d has potential difference V...

Description :  A copper wire of length l and diameter d has potential difference V applied at its two ends. The drift velocity is vd . If the diameter of wire is made d/3, then drift velocity becomes

Last Answer :  A copper wire of length l and diameter d has potential difference V applied at its two ends. The drift velocity is vd . If the diameter of wire is made d/3, then drift velocity becomes vd.

The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If the working depression head of the well is 3 m, the minimum diameter of the well, is (A) 2 m (B) 2.25 m (C) 2.50 m (D) 3.00 m

Description : The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If  the working depression head of the well is 3 m, the minimum diameter of the well, is  (A) 2 m  (B) 2.25 m  (C) 2.50 m  (D) 3.00 m 

Last Answer : (D) 3.00 m 

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

The Reynold's number of a ship is __________ to its velocity and length. (A) Directly proportional (B) Inversely proportional (C) Square root of velocity (D) None of these

Description : The Reynold's number of a ship is __________ to its velocity and length. (A) Directly proportional (B) Inversely proportional (C) Square root of velocity (D) None of these

Last Answer : Answer: Option A

A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1:25 model be towed through water? (A) 10 m/sec (B) 25 m/sec (C) 2 m/sec (D) 50 m/sec

Description : A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1:25 model be towed through water? (A) 10 m/sec (B) 25 m/sec (C) 2 m/sec (D) 50 m/sec

Last Answer : Answer: Option C

1. Critical angle of. light passing from glass to water is minimum for which colour? 2. With whose assistance was Bokaro Steel Limited established? 3. Where were the xxvii (1996) Summer Olympic games were held? 4. Why was Farakka Barrage commissioned? 5. In the Sultanate period, which was the highest rural authority for land revenue?

Description : 1. Critical angle of. light passing from glass to water is minimum for which colour? 2. With whose assistance was Bokaro Steel Limited established? 3. Where were the xxvii (1996) Summer Olympic games ... can be drawn on the earth's surface passes through where? 20. By whom was Zero invented?

Last Answer : Answer : 1. Violet colour 2. Soviet Union 3. Atlanta 4. Save Kolkata port 5. Chowdhary 6. 10% 7. Governor-General 8. 2CaSO4 .H2 O 9. Atlantic ocean 10. Caste system 11. Football 12. Excise duties ... . Government of India Act, 1858 17. Air 18. Sri Sri Ravi Shankar 19. Equator 20. An unknown Indian 

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Last Answer : (B) 12.88

The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Description : The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Last Answer : Option A

The most practical method used for resurfacing a ship's service motor commutator is to _____________. A. turn it down in the ship's lathe B. use a grinding rig C. use a hand stone D. burnish it with commutator stones

Description : The most practical method used for resurfacing a ship's service motor commutator is to _____________. A. turn it down in the ship's lathe B. use a grinding rig C. use a hand stone D. burnish it with commutator stones

Last Answer : Answer: B

The equivalent length of a column fixed at one end and free at the other end, is (A) 0.5 l (B) 0.7 l (C) 2 l (D) 1.5 l

Description : The equivalent length of a column fixed at one end and free at the other end, is (A) 0.5 l (B) 0.7 l (C) 2 l (D) 1.5 l

Last Answer : (C) 2 l

The equivalent length of a column fixed at both ends, is (A) 0.5 l (B) 0.7 l (C) l (D) 1.5 l

Description : The equivalent length of a column fixed at both ends, is  (A) 0.5 l (B) 0.7 l (C) l (D) 1.5 l

Last Answer : (A) 0.5 l

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Last Answer : (B) 102 kg

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Description : A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Last Answer : (B) 0.207 L

A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Description : A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Last Answer : Answer: Option D

To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Description : To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Last Answer : Answer: Option B

The safe length L of a valley curve for night travel is (A) 2S - (1.50 + 0.035 S)/N if L < S (B) NS²/(1.50 + 0.035 S) if L > S (C) Neither (a) nor (b)(D) Both (a) and (b

Description : The safe length L of a valley curve for night travel is (A) 2S - (1.50 + 0.035 S)/N if L < S (B) NS²/(1.50 + 0.035 S) if L > S (C) Neither (a) nor (b) (D) Both (a) and (b

Last Answer : Answer: Option D