The minimum number of rivets for the connection of a gusset plate, is (A) 1 (B) 2 (C) 3 (D) 4

The minimum number of rivets for the connection of a gusset plate, is
(A) 1
(B) 2
(C) 3
(D) 4
by

1 Answer

Answer :

(B) 2
by

Related questions

Failure of riveted joints is due to (A) Tearing of the plates between the rivet hole and the edge of the plate (B) Tearing of plates between rivets (C) Shearing of rivets (D) All the above

Description : Failure of riveted joints is due to  (A) Tearing of the plates between the rivet hole and the edge of the plate  (B) Tearing of plates between rivets  (C) Shearing of rivets  (D) All the above 

Last Answer : (D) All the above 

Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%? (A) Small punches, broaches reamers and springs (B) Cutlery, screws, rivets and files (C) Mandrels, twist drills, small lathe tools and razors (D) Forgings like can shaft, structural steel plate, threading dies and drawing dies

Description : Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%? (A) Small punches, broaches reamers and springs (B) Cutlery, screws, rivets and files (C) ... lathe tools and razors (D) Forgings like can shaft, structural steel plate, threading dies and drawing dies

Last Answer : (A) Small punches, broaches reamers and springs

Renewal of slack rivets should be taken up in steel girder bridges: a) All rivets which are hand loose or which have lost 50% of their head by corrosion. b) All hammer loose rivets where corrosion has set in between the head and the plate. c) In end stiffeners when the percentage of hammer loose rivets is >30% d) All the above*

Description : Renewal of slack rivets should be taken up in steel girder bridges: a) All rivets which are hand loose or which have lost 50% of their head by corrosion. b) All hammer loose rivets where corrosion has set ... . c) In end stiffeners when the percentage of hammer loose rivets is >30% d) All the above*

Last Answer : d) All the above*

The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Description : The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Last Answer : d) 2.5 x d*

The minimum edge distance for rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.5 x d* d) 2.5 x d

Description : The minimum edge distance for rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.5 x d* d) 2.5 x d

Last Answer : c) 1.5 x d*

The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Description : The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Last Answer : (A) Pitch

When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Description : When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Last Answer : (D) Double riveted double cover butt joint

If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Description : If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Last Answer : (C) Diamond riveting

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

In flange splices when the number of hammer and hand loose rivets is 30% or more of the total rivets on any side of the splice location, a) Need no be renewed b) wait for 100% loose rivets c) all the rivets should be renewed.* d) None of the above

Description : In flange splices when the number of hammer and hand loose rivets is 30% or more of the total rivets on any side of the splice location, a) Need no be renewed b) wait for 100% loose rivets c) all the rivets should be renewed.* d) None of the above

Last Answer : c) all the rivets should be renewed.*

Where can I find these briolette jewel rivets?

Description : Where can I find these briolette jewel rivets?

Last Answer : Have you tried Rio Gems/Findings?

How do you remove rivets?

Description : How do you remove rivets?

Last Answer : Find a drill bit a little smaller than the rivets. Drill the rivet out. It should come right out as soon as it gets through the middle of the rivet. The original hole is left as it was. This is ... back together. You can put the same sized rivets back in the holes if you have a rivet gun and rivets

How many rivets in the golden gate bridge?

Description : How many rivets in the golden gate bridge?

Last Answer : 600,000 in each of the two towers

Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Description : Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Last Answer : (B) Boiler plates, rivets etc.

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature of 40°C C. minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Description : One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature ... . minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Last Answer : Answer: B

For a distillation column operating at minimum reflux, the (A) Concentration of liquid and vapour leaving a plate will be same (B) Reflux ratio will be maximum (C) Number of plates required will be maximum

Description : For a distillation column operating at minimum reflux, the (A) Concentration of liquid and vapour leaving a plate will be same (B) Reflux ratio will be maximum (C) Number of plates required will be maximum

Last Answer : (C) Number of plates required will be maximum

In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Description : In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Last Answer : (A) Total

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

What is the minimum bandwidth required for broadband connection: a) 128 kbps b) 256 kbps c) 512 kbps d) None of These

Description : What is the minimum bandwidth required for broadband connection: a) 128 kbps b) 256 kbps c) 512 kbps d) None of These

Last Answer : b) 256 kbps

The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the Vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto (A) 5" (B) 10" (C) 15" (D) 20"

Description : The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the Vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto (A) 5" (B) 10" (C) 15" (D) 20"

Last Answer : (D) 20"

In horizontal angles, the error due to imperfect levelling of the plate bubble is (A) Large when sights are nearly level (B) Large for long sights (C) Less for steeply inclined sights (D) Large for steeply inclined sights

Description : In horizontal angles, the error due to imperfect levelling of the plate bubble is (A) Large when sights are nearly level (B) Large for long sights (C) Less for steeply inclined sights (D) Large for steeply inclined sights

Last Answer : (D) Large for steeply inclined sights

If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is given by (A) (b + d)/b (B) (b - d)/b (C) (d - b)/d (D) (b - d)/d

Description : If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is  given by  (A) (b + d)/b (B) (b - d)/b (C) (d - b)/d (D) (b - d)/d

Last Answer : (B) (b - d)/b

According to Unwin's formula, the diameter of a rivet of plate of thickness is : (A) d = 6.05 t (B) d = 1.5 t + 4 (C) d = t(D) d = t + 1.5

Description : According to Unwin's formula, the diameter of a rivet of plate of thickness is :  (A) d = 6.05 t (B) d = 1.5 t + 4  (C) d = t (D) d = t + 1.5 

Last Answer : (A) d = 6.05 t

The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is (A) Less than one (B) Equal to one (C) More than one (D) Equal

Description : The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is  (A) Less than one  (B) Equal to one  (C) More than one  (D) Equal 

Last Answer : (D) Equal 

From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Description : From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Last Answer : (A) 0.5 cm

A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Last Answer : (C) 50 mm

In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Last Answer : (B) Between 300 mm and 750 mm

Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug out whose size is kept equal to the size of the test plate (C) Bottom level of the hole dug at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Description : Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug ... at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Last Answer : Answer: Option D

A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Description : A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of ... (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Last Answer : Answer: Option B

01. Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, at right angles to the direction of flow of the liquid is known as lift. A) True B) False

Description : 01. Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, at right angles to the direction of flow of the liquid is known as lift. A) True B) False

Last Answer : A

Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Description : Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Last Answer : Answer: Option B

Which of the following instrument can be used for measuring speed of a submarine moving in deep sea? (A) Venturimeter (B) Orifice plate (C) Hot wire anemometer (D) Pitot tube

Description : Which of the following instrument can be used for measuring speed of a submarine moving in deep sea? (A) Venturimeter (B) Orifice plate (C) Hot wire anemometer (D) Pitot tube

Last Answer : Answer: Option D

Which of the following instrument can be used for measuring speed of an aeroplane? (A) Venturimeter (B) Orifice plate (C) Pitot tube(D) Rotameter

Description : Which of the following instrument can be used for measuring speed of an aeroplane? (A) Venturimeter (B) Orifice plate (C) Pitot tube (D) Rotameter

Last Answer : Answer: Option C

Which of the following instruments is used to measure flow on the application of Bernoulli's theorem? (A) Venturimeter (B) Orifice plate (C) Nozzle (D) All of the above

Description : Which of the following instruments is used to measure flow on the application of Bernoulli's theorem? (A) Venturimeter (B) Orifice plate (C) Nozzle (D) All of the above

Last Answer : Answer: Option D

Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Description : Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Last Answer : Answer: Option D

When a plate is immersed in a liquid parallel to the flow, it will be subjected to a pressure __________ that if the same plate is immersed perpendicular to the flow. (A) Less than (B) More than (C) Equal to (D) None of these

Description : When a plate is immersed in a liquid parallel to the flow, it will be subjected to a pressure __________ that if the same plate is immersed perpendicular to the flow. (A) Less than (B) More than (C) Equal to (D) None of these

Last Answer : Answer: Option A

Bullet proof glass is made of thick glass sheet sandwiched by a layer of (A) Steel (B) Stainless steel (C) High test plastic (D) Chromium plate

Description : Bullet proof glass is made of thick glass sheet sandwiched by a layer of (A) Steel (B) Stainless steel (C) High test plastic (D) Chromium plate

Last Answer : Answer: Option C

If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted with complete dewatering continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Description : If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted ... continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Last Answer : (c) Test should be conducted with complete dewatering continuously throughout the test duration

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

Consider the following assumption made in the analysis of a jet impinging normally on a moving plate to introduce the principle of moment of momentum: 1. Friction between jet and plate is neglected. 2. Flow is steady 3. Impinging momentum of jet is uncharged. 4. Plate moves at a constant velocity. Which of these statements are relevant? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 & 4

Description : Consider the following assumption made in the analysis of a jet impinging normally on a moving plate to introduce the principle of moment of momentum: 1. Friction between jet and plate is neglected. 2. Flow is steady 3. Impinging momentum of ... b) 1, 2 & 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 & 4

Last Answer : (a) 1, 2 & 4 only

Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the footing. 3. Size effects in plate load tests are more important in case of cohesionless soils. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the ... , 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (d) 1 & 3 only

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Description : The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Last Answer : d/85

In case of Magnel- Blaton system of prestressing, each sandwich plate can generally anchor (a) 6 wires (b) 8 wires (c) 10 wires (d) 16 wires

Description : In case of Magnel- Blaton system of prestressing, each sandwich plate can generally anchor (a) 6 wires (b) 8 wires (c) 10 wires (d) 16 wires

Last Answer : (a) 6 wires

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness