Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln

Which of the following is a directly fired intermittent furnace?
(A) Walking beam reheating furnace
(B) Reverberatory furnace
(C) Tower furnace
(D) Tunnel kiln
by

1 Answer

Answer :

(B) Reverberatory furnace
by

Related questions

An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Last Answer : (A) Walking beam

Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Last Answer : (C) Soaking pit

Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Description : Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Last Answer : (D) Boiler furnace

Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Last Answer : (C) Boiler furnace

Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Last Answer : (A) Cold rolled steel coil annealing

The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Last Answer : (B) 40

Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Last Answer : (A) By-product coke oven

Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Description : Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Last Answer : (B) Annealing furnace

Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Last Answer : (C) Tunnel kiln

Cement Kiln is a (A) Rotary Kiln (B) Tunnel Kiln (C) Natural draft furnace (D) Batch furnace

Description : Cement Kiln is a (A) Rotary Kiln (B) Tunnel Kiln (C) Natural draft furnace (D) Batch furnace

Last Answer : (A) Rotary Kiln

In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Description : In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Last Answer : (C) Radiation of heat from the roof of the combustion chamber

Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting

Description : Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting

Last Answer : (A) Roasting/reduction of ores

Calcination of limestone to produce lime is done in a __________ kiln. (A) Tunnel (B) Rotary (C) Vertical shaft (D) Both (B) and (C)

Description : Calcination of limestone to produce lime is done in a __________ kiln. (A) Tunnel (B) Rotary (C) Vertical shaft (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Choose the correct option the code regarding roasting process. (I) It is the process of heating the ore in air in a reverberatory furnace to obtain th

Description : Choose the correct option the code regarding roasting process. (I) It is the process of heating the ore in air in a reverberatory furnace to obtain th

Last Answer : Choose the correct option the code regarding roasting process. (I) It is the process of heating the ore in air ... III and IV D. I , II , III and IV

Assertion: Wrough iron is prepared from cast iron by oxidising impurities in a reverberatory furnace lined with haematite. Reason: Haematite oxidises

Description : Assertion: Wrough iron is prepared from cast iron by oxidising impurities in a reverberatory furnace lined with haematite. Reason: Haematite oxidises

Last Answer : Assertion: Wrough iron is prepared from cast iron by oxidising impurities in a reverberatory furnace lined ... -1 is false but Statement -2 is true

When copper ore is mixed with silica in a reverberatory furnace, copper matte is produced. The copper matter contains__________

Description : When copper ore is mixed with silica in a reverberatory furnace, copper matte is produced. The copper matter contains__________

Last Answer : When copper ore is mixed with silica in a reverberatory furnace, copper matte is produced. The copper ... sulphides of copper (I) and iron (III)

Pick up the correct statement from the following: (A) Bull's trench kiln a trench excavated in ground (B) Hoffman's kiln is constructed over ground (C) Tunnel Kiln is constructed as a tunnel (D) All the above

Description : Pick up the correct statement from the following: (A) Bull's trench kiln a trench excavated in ground (B) Hoffman's kiln is constructed over ground (C) Tunnel Kiln is constructed as a tunnel (D) All the above

Last Answer : Answer: Option D

An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Last Answer : (B) Muffle furnace

Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Last Answer : (B) Reheating furnace

__________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Last Answer : (B) Muffle furnace

Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Description : Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Last Answer : (B) Slabs

Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace(C) Steam boiler(D) Coke oven

Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven

Last Answer : (D) Coke oven

Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Description : Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Last Answer : (A) Cupola

The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Firing glass in a kiln: can a piece be fired twice?

Description : Firing glass in a kiln: can a piece be fired twice?

Last Answer : Yes. Firing at these low temperatures doesn’t make any fundamental change in the structure of the glass.

Does ceramics have to be fired in a kiln?

Description : Is it possible to do ceramic things if I don't have a kiln? For example in the oven? But it's probably low temperature huh?

Last Answer : Ceramics (depending on the type of clay and glaze) need temperatures above 1000 ° C (up to 1250 ° C) - you will reach a maximum of less than 300 ° C in the oven. If you have space, ... -mala-vysokozarna-pec-na-vypalovani-keramiky-drevem.html). If not, look around for the pottery that the kiln has.

Who makes thing from clay which are fired in a kiln?

Description : Who makes thing from clay which are fired in a kiln?

Last Answer : Feel Free to Answer

Who makes things made of clay which are fired in kiln?

Description : Who makes things made of clay which are fired in kiln?

Last Answer : Feel Free to Answer

A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these

Description : A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these

Last Answer : (B) Muffle furnace

Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter

Description : Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter

Last Answer : (B) Blast furnace

Refractory bricks having high thermal conductivity is desirable, when it is to be used in the (A) L.D. converter (B) Blast furnace (C) Rotary kiln (D) Recuperator

Description : Refractory bricks having high thermal conductivity is desirable, when it is to be used in the (A) L.D. converter (B) Blast furnace (C) Rotary kiln (D) Recuperator

Last Answer : (D) Recuperator

Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Last Answer : compressor

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 TPD GCV of coal : 4500 kcal/kg Power Purchased from Grid : 82400 kWh / day Specific Energy consumption for Kiln producing Sponge Iron: 120 kWh / ton sponge iron Calculate the following 1. Specific Energy Consumption of Induction melting furnace in terms of kWh/ton of molten steel 2. Specific Energy Consumption of the entire plant, in terms of kcal/kg of molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace,  producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten  steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Last Answer :  a) Specific Energy Consumption of Induction Melting Furnace  Molten Steel Production from the Induction melting furnace per day  = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE  = 655864000/107  = 65.586 ToE

Which of the following terms refers to leg pain that is brought on walking and caused by arterial insufficiency? a) Intermittent claudication Intermittent claudication is leg pain that is brought on by exercise and relieved by rest. b) Dyspnea Dyspnea is the patient’s subjective statement of difficulty breathing. c) Orthopnea Orthopnea is the inability of the patient to breathe except in the upright (sitting) position. d) Thromboangitis obliterans Thomroangitis obliterans is a peripheral vascular disease also known as Burger’s disease.

Description : Which of the following terms refers to leg pain that is brought on walking and caused by arterial insufficiency? a) Intermittent claudication Intermittent claudication is leg pain that is ... obliterans Thomroangitis obliterans is a peripheral vascular disease also known as Burger's disease.

Last Answer : a) Intermittent claudication Intermittent claudication is leg pain that is brought on by exercise and relieved by rest.

While the fuel fired furnace can be used upto a maximum temperature of about 1700°C, the electric furnace can be used upto a temperature of about __________ °C. (A) 2000 (B) 3000 (C) 4500 (D) 6000

Description : While the fuel fired furnace can be used upto a maximum temperature of about 1700°C, the electric furnace can be used upto a temperature of about __________ °C. (A) 2000 (B) 3000 (C) 4500 (D) 6000

Last Answer : (C) 4500

Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Description : Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Last Answer : (B) 25-30

Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Description : Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Last Answer : (A) < 2

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

rate the efficiency and quality of oil fired furnace manufacturers.?

Description : rate the efficiency and quality of oil fired furnace manufacturers.?

Last Answer : I would look it up in consumer reports if you have it or if not go to the library. Also online people rate stuff all the time and they can tell you what the good ones are and what to ... an article on that subject, and pretty soon you'll know what the most efficient quality oil fired furnace is.

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

'Flare tower' used in industry is meant for (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure (B) Absorbing the pollutant gases from the furnace exhaust (C) Cooling of furnace exhaust gases (D) None of these

Description : 'Flare tower' used in industry is meant for (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure (B) Absorbing the pollutant gases from the furnace exhaust (C) Cooling of furnace exhaust gases (D) None of these

Last Answer : (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure

Statement-1: Silica is added as a flux in reverberatory furnance, in the extraction of copper from copper pyrites. Statement-2: Silica decreases the m

Description : Statement-1: Silica is added as a flux in reverberatory furnance, in the extraction of copper from copper pyrites. Statement-2: Silica decreases the m

Last Answer : Statement-1: Silica is added as a flux in reverberatory furnance, in the extraction of copper from ... Statement-1 is false but Statement -2 is true

Describe in brief with neat sketch construction of tunnel with needle beam method

Description : Describe in brief with neat sketch construction of tunnel with needle beam method

Last Answer : In this method stout timber beam known as needle beam is used which forms the main temporary support during the excavation. Construction steps: (a) First of all a small drift of about 1 1 m is ... . (d) After excavation, the lining is provided to the tunnel section and mucking is done. 

We all know what a nuclear explosion looks like.(fireball and mushroom cloud). What would an orbital beam cannon, fired at the ground continuously for a minute, look like?

Description : We all know what a nuclear explosion looks like.(fireball and mushroom cloud). What would an orbital beam cannon, fired at the ground continuously for a minute, look like?

Last Answer : A few views here: https://www.google.com/search?rlz=1C1GCEB_enUS800US800&biw=1755&bih=1027&tbm=isch&sa=1&ei=PLzYW6KsGOGb0gKU04DwBg&q=rogue+one+death+star+firing&oq=death+star+rogue+&gs_l=img.3.3.35i39j0j0i8i30l8.108464.112049..117621. ... 180.3......1....1..gws-wiz-img.......0i67.46tMYq5Liuc#imgrc=_

Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Description : Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Last Answer : (D) None of these

A man walking along a railraod track sees a train thundering at high speed towards him. Instead of immediately jumpimg off the track, he charges directly at the train for about ten feet and only then gets off the track.Why? -Riddles

Description : A man walking along a railraod track sees a train thundering at high speed towards him. Instead of immediately jumpimg off the track, he charges directly at the train for about ten feet and only then gets off the track.Why? -Riddles

Last Answer : The man was on a bridge when he first saw the train so he couldn't jump off the track immediately.

Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Description : Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Last Answer : (B) 40