Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace
Last Answer : (C) Tunnel kiln
Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace
Last Answer : (C) Soaking pit
Description : A refractory wall separating the stock and the source of heat is provided in a (A) Updraft kiln (B) Muffle furnace (C) Continuous furnace (D) None of these
Last Answer : (B) Muffle furnace
Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these
Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace
Description : Example of an indirectly heated furnace is (A) Hood annealing furnace (B) Muffle furnace (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln
Last Answer : (B) Reverberatory furnace
Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating
Last Answer : (A) Cold rolled steel coil annealing
Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns
Last Answer : (C) Boiler furnace
Description : Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace
Last Answer : (D) Boiler furnace
Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth
Last Answer : (A) Walking beam
Description : Cement Kiln is a (A) Rotary Kiln (B) Tunnel Kiln (C) Natural draft furnace (D) Batch furnace
Last Answer : (A) Rotary Kiln
Description : Refractory bricks having high thermal conductivity is desirable, when it is to be used in the (A) L.D. converter (B) Blast furnace (C) Rotary kiln (D) Recuperator
Last Answer : (D) Recuperator
Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor
Last Answer : compressor
Description : In a muffle furnace, the muffle (A) Retards the heat transfer (B) Assists in temperature equalisation in the charge (C) Permits the use of controlled atmosphere for the protection of stock (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above
Last Answer : Billet Reheating Furnace
Description : The main function of a muffle in the muffle furnace is to (A) Protect the charge from the effects of the products of combustion (B) Smooth out temperature inequalities on the combustion side of the muffle wall (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace
Last Answer : (C) Salt bath furnace
Description : Calcination of limestone to produce lime is done in a __________ kiln. (A) Tunnel (B) Rotary (C) Vertical shaft (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80
Last Answer : (B) 40
Description : Calcination reaction of limestone (CaCO3 → CaO + CO2 ) goes to completion in the rotary kiln, because (A) CaO is not dissociated (B) CO2 escapes continuously (C) Of high calcination temperature (D) CaO is more stable than CaCO3
Last Answer : (B) CO2 escapes continuously
Description : Coal tar is used as a (A) Binding material for coal briquettes (B) Fuel in rotary kiln (C) Binder in making carbon electrodes (D) All (A), (B) and (C)
Description : Rotary kiln is not involved in the production of (A) Cement (B) Lime from limestone (C) Slaked lime from quick lime (D) None of these
Last Answer : (C) Slaked lime from quick lime
Description : Calcination of limestone is not done in a __________ kiln for producing lime. (A) Vertical shaft (B) Rotary (C) Fluidised bed (D) Fixed bed
Last Answer : (D) Fixed bed
Description : Rotary lime kiln is an example of a/an __________ system. (A) Closed (B) Open (C) Isolated (D) Non-thermodynamic
Last Answer : (B) Open
Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85
Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola
Last Answer : (B) Reheating furnace
Description : Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets
Last Answer : (B) Slabs
Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven
Last Answer : (D) Coke oven
Description : Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these
Last Answer : (A) Cupola
Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)
Description : To obtain cement dry powder, lime stones and shales or their slurry, is burnt in a rotary kiln at a temperature between (A) 1100° and 1200°C (B) 1200° and 1300°C (C) 1300° and 1400°C (D) 1400° and 1500°C
Last Answer : D
Description : In the manufacture of cement, the dry of wet mixtue of calcareous and argillaceous materials is burnt in a (a) A Rotary kiln (b) A Grinder (c) Country kiln (d) All the above
Last Answer : (a) A Rotary kiln
Description : Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter
Last Answer : (B) Blast furnace
Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace
Last Answer : (A) By-product coke oven
Description : Regenerator is widely used in: a) Reheating Furnaces b) heat treatment furnaces c) Baking Ovens d) glass melting furnaces
Last Answer : glass melting furnaces
Description : The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing
Last Answer : (D) Solution annealing
Description : Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these
Last Answer : (B) Tempering
Description : The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these
Last Answer : (B) Normalising
Description : Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing
Last Answer : (B) Stress relieving
Description : Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising
Last Answer : (D) Carburising
Description : The heat treatment to which the steel wire containing > 0.25% carbon is subjected to is (A) Full annealing (B) Bright annealing (C) Patenting (D) None of these
Last Answer : C) Patenting
Description : Pick out the wrong statement. (A) Both annealing and normalising release the internal stresses of the material besides improving the mechanical properties (B) Low carbon steel does not respond to ... are also used for surface hardening (D) Martempering of a material is a hardening process
Last Answer : Option C
Description : Which is a continuous furnace? (A) Coke ovens (B) Annealing furnace (C) Glass tank furnace
Last Answer : (C) Glass tank furnace
Description : Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon ... the metal surface) cause nitride formation with increase in surface hardness (D) None of these
Last Answer : (D) None of these
Description : Protective gas used in the annealing furnace for steel coil comprises of (A) 95% N2 + 5% H2 (B) 5% H2 + 9% N2 (C) 100% CO (D) 100% H2
Last Answer : (A) 95% N2 + 5% H2
Description : Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting
Last Answer : (A) Roasting/reduction of ores
Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )
Last Answer : a) Specific Energy Consumption of Induction Melting Furnace Molten Steel Production from the Induction melting furnace per day = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE = 655864000/107 = 65.586 ToE
Description : Which furnace employs natural draft? (A) Coke oven (B) Boiler (C) Rotary kilns (D) L.D. converter
Last Answer : (A) Coke oven